Inhaltszusammenfassung zur Seite Nr. 1
TK-WD310 COLOR VIDEO CAMERA
COLOR VIDEO CAMERA
INSTRUCTIONS
TK-WD310
(A)
VICTOR COMPANY OF JAPAN, LIMITED
For Customer Use:
Enter below the Serial No. which is
located on the body. Retain this
is a registered trademark owned by VICTOR COMPANY OF JAPAN, LTD.
information for future reference.
is a registered trademark in Japan, the U.S.A., the U.K. and other countries.
Model No.TK-WD310
Printed in Thailand
Serial No.
© 2004 VICTOR COMPANY OF JAPAN, LIMITED
LWT0181-001A-H
LWT0181-001A-H
These are
Inhaltszusammenfassung zur Seite Nr. 2
13. Follow all warnings and instructions marked on the appliance. 18. When replacement parts are required, be sure the service techni- 14. Do not overload wall outlets and extension cords as this can result cian has used replacement parts specified by the manufacturer that in fire or electric shock. have the same characteristics as the original part. Unauthorized 15. Never push objects of any kind into this appliance through cabinet substitutions may result in fire, electric shock, or other haza
Inhaltszusammenfassung zur Seite Nr. 3
INTRODUCTION Thank you for purchasing this product. (These instrustions are for TK-WD310U and TK-WD310E.) Before beginning to operate this unit, please read the instruction EASY INSTALLATION manual carefully in order to make sure that the best possible per- The factory default settings are intended to give easy installation. formance is obtained. Please attach a lens, a power supply, a video cable and mount the Features camera securely. You should now have good images. The additional information
Inhaltszusammenfassung zur Seite Nr. 4
INTRODUCTION Operating Precautions (continued) ● The white balance (ATW) of this device is optimally set for sunlight. ● Blemishes: Small spots are normal, the camera contains compen- Proper white balance may not be achieved for artificial lighting such sation functions for blemishes above 120 mV (p-p) in value. Please as fluorescent lighting, etc. contact your JVC authorised dealer for further information. ● If you use this camera in locations where the camera is exposed to ● For temperatures h
Inhaltszusammenfassung zur Seite Nr. 5
INTRODUCTION Names and Operations of Parts [Rear Panel] A [SET] button During normal screen display, pressing and holding this button for more than 2 seconds will display the MENU screen. DC12V SEE INST- ( Page 24) AC24V 1 2 RUCTION MANUAL 8 During MENU screen display, this button is pressed to display or CLASS 2 ONLY (U TYPE) enable the selected menu item. The input digit will change when ISOLATED POWER ONLY (E TYPE) entering the camera title. When selecting EXIT in the TOP MENU screen, press
Inhaltszusammenfassung zur Seite Nr. 6
CONNECTION/INSTALLATION Mounting the lens Mount the lens according to the procedures described below. 1. Before mounting a lens, check whether it is CS-mount lens. Dimension (b) of the lens shown in the illustration must be as shown in the table below. If (b) exceeds the value in the table, it may dam- Lens mount age the inside of the camera or correct mounting may be impos- sible; never use such lenses. The F mark indicates a focal point. Lens Flange back (c) Dimension (b) CS mount lens 12.5mm
Inhaltszusammenfassung zur Seite Nr. 7
CONNECTION/INSTALLATION Mounting the camera Camera mounting screw hole Camera mounting SEE INST- DC12V bracket AC24V 1 2 RUCTION MANUAL CLASS 2 ONLY (U TYPE) 6mm ISOLATED POWER ONLY (E TYPE) SET SELECTOR 2mm POWER VIDEO OUT LL INT M3 × 6 Rotation prevention hole Fall Prevention When mounting the camera on a fixer, pan/tilt, etc., use the camera •Exercise maximum caution when installing the unit to the wall or mounting screw hole located on the camera-mounting bracket. ceiling. You should not eng
Inhaltszusammenfassung zur Seite Nr. 8
CONNECTION/INSTALLATION Back focus adjustment Be sure to make back-focus adjustments when changing the lens mount- • With a fixed-focus lens ing method or using a different lens. If the focus can not be adjusted correctly by rotating the lens focus ring, adjust the back focus as follows. ● To make accurate back focus adjustments, carry out adjustments in a state where the lens iris is released. 1. Loosen the back focus locking screws by turning it counterclock- To open the lens iris, set MODE in
Inhaltszusammenfassung zur Seite Nr. 9
1 MENU SETTING Menu tree About menus The menu screens are structured as shown below. FOCUS ADJUST ............ Used during focus adjustment of the auto iris lens. Page 27 ( Page 27) — — — FOCUS ADJUST — — — MOD E OFF VIDEO ADJUST ............. Sets the wide dynamic range, gain, color tem- EX I T perature, white balance, etc. ( Page 28) CAMERA SETTINGS ..... Sets the DC iris, camera title and vertical Page 28 Page 29 phase. — — — ME NU — — — — — — VI DEO ADJUST — — — — — WDR CUSTOM SETTIN
Inhaltszusammenfassung zur Seite Nr. 10
MENU SETTING VIDEO ADJUST screen (continued) Item Content AGC MODE Default setting: LOW WDR BIAS Sets the low/mid luminance level of the Wide Sets the maximum gain of AGC (Auto Gain Control). Dynamic Range You can set this device to maximum gain by the use of the slow shutter. ● To brighten video with low/mid luminance: Refer to the chart below and set according to the subject. Increase the value ● To darken video with low/mid luminance: Setting : Gain Decrease the value Gain [Setting range
Inhaltszusammenfassung zur Seite Nr. 11
MENU SETTING VIDEO ADJUST screen (continued) COLOR LEVEL Default setting: NORMAL MANUAL WHITE BALANCE screen The color level of video signals is adjusted. If the entire screen appears to be reddish or bluish in color as the result ● To lighten colors: decrease the value. of automatic white balance adjustment, manually adjust the white bal- ● To darken colors: increase the value. ance. [Setting range: -5 ~ NORMAL ~ 5] Preparation — — — V IDEO ADJUST — — — ENHANCE LEVEL Default setting: NORMAL WDR
Inhaltszusammenfassung zur Seite Nr. 12
MENU SETTING FACTORY SETTINGS screen Returns set values to their factory settings. Allowed characters 8 direction (SELECTOR button) t direction Operation 1. Display the FACTORY SET- — — — — — — Space MENU TINGS screen. ( Page 24) FOCUS ADJUST.. VIDEO ADJUST.. 2. Press the SELECTOR button in CAMERA S E T TI. NGS. FACTORY SET TI. NGS. the vertical direction (6 or 7) EX I T and move the cursor (>) to CLEAR. 3. Press the SET button. ● Settings including the camera Cursor title will be restored to
