Inhaltszusammenfassung zur Seite Nr. 1
1080I Multi-purpose
Digital Camera
AK-HC910P
Before attempting to connect, operate or adjust this product, please
read these instructions completely.
Inhaltszusammenfassung zur Seite Nr. 2
For Your Safety FCC Note: CAUTION This device complies with Part 15 of the RISK OF ELECTRIC SHOCK DO NOT OPEN FCC Rules. To assure continued compliance follow the attached instal- CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER (OR BACK). lation instructions and do not make any NO USER SERVICEABLE PARTS INSIDE. unauthorized modifications. REFER TO SERVICING TO QUALIFIED SERVICE PERSONNEL. This equipment has been tested and The lightning flash with found to comply with the lim
Inhaltszusammenfassung zur Seite Nr. 3
CONTENTS For Your Safety...................................2 Setting of Menu Items..............18 to 29 Preface ...............................................4 _ Configuration of menu display screen .........................................18 Features..............................................4 _ USER menu (Initial screen) ........19 Precautions.........................................5 ! Maintenance menu ............20 to 26 Major Operating Controls and 1 Black shading correction Their
Inhaltszusammenfassung zur Seite Nr. 4
Thank you very much for purchasing the multi-purpose digital camera. Preface This camera employs new 2/3q 2.2 million-pixel FIT CCD [1920(H)k1080(V)], realizing a compact light-weight system including the optical system. Also, the newly developed CCD having an FIT configuration suited for higher picture quality and the development of low-noise, high-speed amplifiers have enabled the realization of high sensitivity, high S/N ratio, and wide dynamic range. With the newly developed digital signal p
Inhaltszusammenfassung zur Seite Nr. 5
Precautions DON’TS DO’S • Do not attempt to disassemble the • Refer any servicing to qualified service camera or other units. In order to prevent personnel. electric shock, do not remove screws or • Handle the camera with care. covers. There are no user-serviceable • Protect the precision made lens by parts inside. placing the lens cap over when the • Do not abuse the camera. Avoid striking, camera is not in use. If the lens is not shaking, etc. The camera contains installed, protect the surface
Inhaltszusammenfassung zur Seite Nr. 6
Major Operating Controls and Their Functions _ Front Panel 3 4 1 2 1 Lens Mount 2/3q standard bayonet type (B4 mount) lens is installed. 2 Lens Fixing Ring Knob Lens is fixed by turning the knob counterclockwise. 3 Cable Clamp Used to clamp the lens cable. 4 Lens Connector [LENS] Used to connect the camera cables of the lens. Pin No. Signal Pin No. Signal 1 Return control 7 Iris follow 9 1 8 2 2 VTR-S/S 8 Iris auto selection 10 3 3 UNREG GND 9 —— 7 12 11 6 4 4 Iris manual selection 10 —— 5 5 Iri
Inhaltszusammenfassung zur Seite Nr. 7
Major Operating Controls and Their Functions 6 Camera mounting hole (1/4-20UNC) 7 Camera mounting hole (3/8-16UNC) The screw holes can be used to secure the camera for installing it on camera housing, and when using a pan/tilt head or a tripod. _ Side Panel BREAKER 8 ZOOM/ FOCUS 9 1 SDI OUT : 2 ; 1/ F 8 Breaker [BREAKER] If the breaker is operated due to over-current or the like, check the cause and eliminate the trouble, then press the breaker button. 9 Zoom/Focus Connector [ZOOM/FOCUS] Used t
Inhaltszusammenfassung zur Seite Nr. 8
Be sure to ask the dealer for the installation, How to Install adjustment and connection of this equipment. _ How to set the lens • Standard 2/3q bayonet type (B4 mount) lens of any makers can be used*. 1 Turn the lens fixing ring knob counterclockwise to remove the lens mount cap. 2 Set the lens in place, and turn the lens fixing ring knob clockwise to precisely fix the lens. 3 Connect the lens cable to the lens connector. 4 Connect the remote (zoom/focus control) cable to the zoom/focus connec
Inhaltszusammenfassung zur Seite Nr. 9
How to Set Up the System (Connection) _ Connection of remote control box • Use multi-cable for the connection of HD controller AK-HRP900 and this unit. BREAKER ZOOM/ FOCUS Coaxial Cable HD-SDI (5C-FB) 1 SDI OUT 2 D-sub 15-pin HD Monitor 1/ F AK-HC910P Video Input Multi-cable (5m) Signal AK-HDMLTCA05 HD Monitor YPbPr O I External AC Adaptor sync AW-PS505 NOTE signal Note that the monitor output is (3 value attenuated and deteriorated if sync) the cable is too long. DC Power Cable D-sub
Inhaltszusammenfassung zur Seite Nr. 10
Multi-purpose Digital Camera Control System Configuration 1 Remote (zoom/focus control) cable BREAKER ZOOM/ FOCUS HD-SDI Coaxial Cable (5C-FB) 1 SDI OUT 2 1/ F D-sub 15-pin Remote Multi-purpose controllable Digital Camera lens AK-HC910P Multi-cable (5m) AK-HDMLTCA05 HD Monitor O I AC Adaptor AW-PS505 External sync signal (3 value sync) DC D-sub 15-pin Power Cable HD Controller AK-HRP900 10
Inhaltszusammenfassung zur Seite Nr. 11
Multi-purpose Digital Camera Pan/Tilt Head Compatible System Configuration 1 Remote controllable BREAKER FOCUS ZOOM/ lens HD-SDI Coaxial Cable (5C-FB) 1 SDI OUT 2 1/ F Multi-cable (5m) Multi-purpose Digital AK-HDMLTCA05 Camera AK-HC910P Remote (zoom/focus control) cable O I AC Adaptor AW-PS300 DC Power Cable DC12V CONTROL IN IN HD Monitor 1394 IP/RP CSOP G/L IN Pb OUT Pr /SDI Y/VIDEO OUT OUT O I Pan/Tilt Head AW-PH300A AC Adaptor AW-PS505 External sync signal NOTE: (3 value sync)
Inhaltszusammenfassung zur Seite Nr. 12
Multi-purpose Digital Camera Control System Configuration 2 (System for remotely monitoring picture control) Remote (zoom/focus control) cable Multi-cable (5m) AK-HDMLTCA05 BREAKER ZOOM/ FOCUS HD-SDI Coaxial Cable (5C-FB) 1 SDI OUT 2 Relay box 1/ F AK-HTF900 Remote Multi-purpose controllable Digital Camera Transfer lens AK-HC910P DC Power O I Cable AC Adaptor AW-PS505 Multi-cable (5m) AK-HDMLTCA05 HD Monitor O I AC Adaptor AW-PS505 DC Power Cable HD Controller AK-HRP900 12
Inhaltszusammenfassung zur Seite Nr. 13
Multi-purpose Digital Camera Pan/Tilt Head Compatible System Configuration 2 (System for remotely monitoring picture control) Remote Multi-cable (5m) controllable AK-HDMLTCA05 BREAKER ZOOM/ FOCUS lens HD-SDI Coaxial Cable (5C-FB) 1 SDI OUT 2 Relay box 1/ F AK-HTF900 Multi-purpose Digital Remote Camera AK-HC910P Transfer (zoom/focus control) cable O I AC Adaptor AW-PS505 Multi-cable (5m) AK-HDMLTCA05 DC12V CONTROL IN IN HD Monitor 1394 IP/RP CSOP DC Power G/L IN Pb OUT Pr /SDI Y/VIDEO
Inhaltszusammenfassung zur Seite Nr. 14
Operation Procedure 1 Turn on the power of each 5 Adjust the black balance. equipment. • This adjustment is needed when the camera is used for the first time or 2 Properly adjust the light for the after leaving unused for a long time. object. • The adjustment is necessary when the ambient temperature is greatly 3 Adjust the flange back of the lens, changed or at the change of season. the iris and the focus. • After adjusting the black balance once, re-adjustment is not needed • Flange back must
Inhaltszusammenfassung zur Seite Nr. 15
How to Adjust _ Flange back adjustment (for zoom lens) The adjustment is to adjust the focus in all the range from the maximum zoom to the widest angle of the zoom lens. 1 Shoot a dark object to open the iris. 2 Adjust the distance from the object to 6.6 ft. (2 m) at least, then loosen the flange back fixing knob of the lens. 3 Set the lens to the maximum zoom and adjust the focus by turning the focus ring. 4 Set the lens to the widest angle and adjust the focus by turning the flange back adjust
Inhaltszusammenfassung zur Seite Nr. 16
How to Adjust _ White balance adjustment Adjust the white balance after shooting a white object by at least 50% of the screen. NOTE: If the white signal level is over 100% or less than 50%, the white balance may not be normally adjusted. _ Color temperature and while balance adjustment (reference) When carbon is burnt, it develops 10000K various colors of light depending on the Blue sky temperature. Natural light can be 9000K Rainy specified by color temperature reflecting to the color developed
Inhaltszusammenfassung zur Seite Nr. 17
How to Adjust _ Black balance adjustment • Adjust it with the lens closed. When the motor drive lens is controlled from the camera, adjusting the black balance causes the lens to be automatically closed. _ Gen lock adjustment When multiple cameras are used or the camera is combined with other equipment, it is necessary to adjust the phase for phase matching by external synchronization. • Horizontal phase adjustment Observe the waveforms of externally synchronizing signal input (black burst signa
Inhaltszusammenfassung zur Seite Nr. 18
Setting of Menu Items _ Configuration of menu display screen USER MENU Maintenance menu 1.MAINTENANCE MAINTENANCE 2.SETTING °° 3.CAM ID 1.BLACK SHADING 2.PED,GAMMA,FLARE 4.FILE MENU 3.KNEE,WHITE CLIP 4.R/B GAIN 5.DTL 6.GAIN,AUTO IRIS 7.S.GAIN 1 8.S.GAIN 2 9.S.GAIN 3 10.MATRIX 11.COLOR CORRECTION1 12.COLOR CORRECTION2 USER MENU Using condition setting menu SETTING °° °° 1.MODE 2.SHUTTER 3.H.PHASE Camera ID s
Inhaltszusammenfassung zur Seite Nr. 19
Setting of Menu Items _ USER menu (Initial screen) The readout data at start of power supply USER MENU is the data just before cutting off the power supply, and the operation is started with 1.MAINTENANCE the data. 2.SETTING 3.CAM ID 1. MAINTENANCE 4.FILE MENU It sets various adjusting data. 2. SETTING It sets various modes. 3. CAM ID It sets the camera ID. 4. FILE MENU It executes file loading and saving, and makes the basic setting of data display. Menu operation is executed by
Inhaltszusammenfassung zur Seite Nr. 20
Setting of Menu Items ! Maintenance menu • Move the cursor (arrow mark) to the item MAINTENANCE °° to be adjusted and press the MENU key, 1.BLACK SHADING then it enters the adjustment menu 2.PED,GAMMA,FLARE thereunder. 3.KNEE,WHITE CLIP 4.R/B GAIN • Move the cursor to MAINTENANCE and 5.DTL press the MENU key, then it returns to 6.GAIN,AUTO IRIS 7.S.GAIN 1 USER MENU. 8.S.GAIN 2 9.S.GAIN 3 10.MATRIX 11.COLOR CORRECTION1 12.COLOR CORRECTION2 1 Blac
