Bedienungsanleitung GE 206C1559P148

Inhaltszusammenfassung zur Seite Nr. 1

Installation
Built-In
Dishwasher
Instructions
BEFORE YOU BEGIN
IMPORTANT The dishwasher
Read these instructions completely and
MUST be installed to allow for future removal from
carefully .
the enclosure if service is required.
If you received a damaged dishwasher , you should
immediately contact your dealer or builder.
IMPORT ANT Observe all
—
governing codes and ordinances.
Note to Installer –  Be sure to leave these instructions
for the and In insp spe ec cto torr ′  s use.
local
Note to C

Inhaltszusammenfassung zur Seite Nr. 2

Installation Preparation PARTS SUPPLIED: Two #8 Phillips flat head wood screws, 5/8" long to secure dishwasher to underside of countertop (in literature package). 2 Wood Screws MATERIALS YOU WILL NEED : Ferrule, compression nut and 90°Elbow (3/8"NPT external thread on one end, opposite end sized to fit water supply) Hand Wire Nuts (3) Thread seal tape Shut-Off Thread 90°Elbow, UL Listed wire nuts (3) Valve Seal Tape Ferrule and Compression Nut Materials For New Installations Only: Air gap

Inhaltszusammenfassung zur Seite Nr. 3

Installation Preparation PREPARE DISHWASHER ENCLOSURE The dishwasher must be installed so that drain hose is no more than 10 feet in length for proper drainage. The dishwasher must be fully enclosed on the top, sides and back, and must not support any part of the enclosure. 32-1/2to 35" 24" Countertop CLEARANCES: When Underside of Min. installed into a corner, 4 Countertop allow 2" min. clearance Dishwasher to Floor between dishwasher and Cabinets adjacent cabinet, wall or Square other applianc

Inhaltszusammenfassung zur Seite Nr. 4

Installation Preparation PREPARE ELECTRICAL WIRING WARNING FOR PERSONAL SAFETY: Remove house fuse or open circuit breaker before beginning installation. Do not use an 1-1/2" Dia. extension cord or adapter plug with this Hole (Max.) appliance. 3" Electrical Requirements from This appliance must be supplied with 120V, 60 Hz., and Cabinet connected to an individual properly grounded branch 24" circuit, protected by a 15 or 20 ampere circuit breaker from Wall or time delay fuse. Wiring must be 2 wir

Inhaltszusammenfassung zur Seite Nr. 5

Installation Instructions BEFOR YOU BEGIN PREPARE HOT WATER LINE Locate and set aside the package containing The line may enter from Either side, rear or floor Locate set aside within the shaded area shown in Figure F. 2 phillips head countertop mounting screws 2 Phillips screws The line may pass through the same hole as the and 2 additional toekickscrews(located in and 2 in electrical cable and Drain hose. Or, Cut an additional the literature). the literature package). 1-1/2" dia. hole to

Inhaltszusammenfassung zur Seite Nr. 6

Inhaltszusammenfassung zur Seite Nr. 7

Inhaltszusammenfassung zur Seite Nr. 8

Inhaltszusammenfassung zur Seite Nr. 9

Inhaltszusammenfassung zur Seite Nr. 10

Inhaltszusammenfassung zur Seite Nr. 11

Inhaltszusammenfassung zur Seite Nr. 12

Installation Instructions STEP 16 DISHWASHER WET TEST Turn on power supply(or plug power cord into outlet, if equipped). Select N″″ ormal wash program. Close the door. Check to be sure that water enters the dishwasher.If water does not enter the dishwasher,check to be sure that water and power are turn on. Check for leaks under the dishwasher.If a leak is found,turn power supply off,then tighten connections.Restore power afterleak is corrected. Check for leaks.around the door. A leak aroun