Inhaltszusammenfassung zur Seite Nr. 1
INSTRUCTIONMANUAL
1
1/2 H.P. Dust Collector
(Model 50-665)
Shown with Accessory
Dust Collector Drum
DATED 8-8-99 PART NO. 1342493
'Delta International Machinery Corp. 1999
Inhaltszusammenfassung zur Seite Nr. 2
TABLE OF CONTENTS SAFETYRULES................................................................................................................................3 IMPORTANTSAFETYRULESFORDUSTCOLLECTORS.............................................................4 INTRODUCTION................................................................................................................................4 UNPACKING..........................................................................................
Inhaltszusammenfassung zur Seite Nr. 3
IMPORTANT SAFETYRULES W oodworking can be dangerous if safe and proper operating procedures are not followed. As with all machinery, there are certain hazards involved with the operation of the product. Using the machine with respect and caution will considerably lessen the possi- bility of personal injury. However, if normal safety precautions are overlooked or ignored, personal injury to the operator may result. Safety equipment such as guards, push sticks, hold-downs, featherboards, goggles,
Inhaltszusammenfassung zur Seite Nr. 4
IMPORTANTSAFETYRULESFOR DUSTCOLLECTORS 10. D ONOTpull the dust collector by the power cord. WARNING: Basic precautions should NEVER allow the power cord to come in contact with always be followed when using your dust collector. sharp edges, hot surfaces, oil or grease. To reduce the risk of injury, electrical shock or fire, comply with the safety rules listed below: 11. D O NOT unplug the dust collector by pulling on the power cord. ALW AYS grasp the plug, not the cord. 1. READ and understand th
Inhaltszusammenfassung zur Seite Nr. 5
UNPACKING Carefully unpack the dust collector from the shipping container and check for any damaged or missing parts. Fig. 2, illustrates the components of the dust collector. 2 3 1 4 10 5 8 12 13 6 9 7 11 15 14 Fig. 2 1. Blower and Motor Assembly 10. Hardware for Mounting Cylinder to Cover, Includes: 1/4-20 x 5/8 Hex Head Screws, 2. VacuumHose Flat Washers, and Locknuts (4 ea.) 3. Cylinder 11. Reducer 4. Dust Bag Elbow 12. Inlet Elbows (2) 5. Hose Clamps (2) 13. Gasket Material 6. Dust Bag 14.
Inhaltszusammenfassung zur Seite Nr. 6
ASSEMBLY 1. Place gasket (A)Fig. 3, on bottom of motor and blower assembly (B). Align four holes in gasket with holes in motor and blower assembly and assemble cover (C) Fig. 3, to gasket and motor and blower assembly with four hex head screws, flat washers, lockwashers, and locknuts (D). B C A D Fig. 3 2. Fig. 4, illustrates the cover (C) assembled to the underside of motor and blower assembly (B). 3. Peel the adhesive paper (E) Fig. 5, from the back of C the gasket material (F) and press the g
Inhaltszusammenfassung zur Seite Nr. 7
J 5. Position the remaining inlet elbow (K) Fig. 8, at the underside of dust collector lid (C)as shown. Align the mounting holes in inlet elbows (K) Fig. 8, with screws (J) Fig. 7 assembled to upper inlet elbow (H) shown in Fig. 7, STEP4, and fasten the upper and lower inlet elbows to the cover with remaining two flat washers, lockwashers, and locknuts (J) Figs. 7 and 8. H C J K Fig. 8 6. Place the sheet metal cylinder (L)Fig. 9, onto the N underside of the cover .Align four holes in cylinder br
Inhaltszusammenfassung zur Seite Nr. 8
W V L CAUTION:Never remove safety grid for any reason except to perform maintenance procedures. There is a high speed blower wheel inside the blower housing that can amputate fingers, grab loose clothing or W neckties. Make certain the dust collector is discon- Fig. 12 nected from the power source before performing any maintenance procedures. 8. Place the entire blower and motor assembly (C) Fig. 13, into collection drum (R) (not supplied). C R Fig. 13 T V P WARNING: The dust collector has a saf
Inhaltszusammenfassung zur Seite Nr. 9
10. Insert the bag clamp (Z) Fig. 16, through the loops of the dust bag (A). Z A Fig. 16 11. Clamp dust bag (A)Fig. 17, to bag elbow (V)as shown by fastening bag clamp (Z). V Z A Fig. 17 12. Assemble reducer (B) Fig. 18, over the end of inlet elbow (H). H B Fig. 18 13. Assemble hose clamp (C) Fig. 19, over one end of hose (D). Assemble hose (D) onto reducer (B) and tighten clamp (C) to hold hose onto reducer. B C D Fig. 19 9
Inhaltszusammenfassung zur Seite Nr. 10
CONNECTING DUSTCOLLECTOR TO POWER SOURCE Before connecting your dust collector to an electrical power system, be sure the motor rating agrees with the electrical system it is to be connected to. SINGLEPHASEOPERATION If the motor on your dust collector is wired for 115 Volt, single phase, the power cord is equipped with a plug that has two flat, parallel current-carrying prongs, and one longer round or U shaped ground prong which requires a mating 3-conductor grounded type receptacle, as shown in
Inhaltszusammenfassung zur Seite Nr. 11
A B Fig. 23 LOCKINGSWITCHIN THE OFF POSITION W e suggest when the dust collector is not in use that the ON/OFF switch be locked in the OFF position. This can be done by grasping the switch toggle (B) Fig. 23, and pulling it out of the switch (A) as shown. W ith the switch toggle (B) removed, the switch will not operate. However, should the switch toggle (B) Fig. 23, be removed while the machine is running, it can be turned OFF, but cannot be restarted without inserting the switch toggle (B) back
Inhaltszusammenfassung zur Seite Nr. 12
Delta Building Trades and Home Shop Machinery Two Year Limited Warranty Delta will repair or replace, at its expense and at its option, any Delta machine, machine part, or machine accessory which in normal use has proven to be defective in workmanship or material, provided that the customer returns the product prepaid to a Delta factory service center or authorized service station with proof of purchase of the product within two years and provides Delta with reasonable opportunity to verify the
