Inhaltszusammenfassung zur Seite Nr. 1
F1-ACE
Digital Set-Top Box
for Free-To-Air
User's manual
Remote Control Unit 1~2
Specification
3~4
Support & Copyright
5
Safety 6
STB Connections 7~11
Reference 11
Guide of Functions 12~16
Guide of Main Menu 17~33
Motorised System 34~37
Trouble Shooting Guide 38~39
Menu Tree 40
Inhaltszusammenfassung zur Seite Nr. 2
Remote Control Unit 1.Remote Control Unit (RCU) Information key i Displays the programme information box on the screen and is also used as the RED key in the menus. Soundtrack key Selects the soundtrack list for the current service and is also used as the GREEN key in the menus. Subtitle key Selects the subtitle language list for the current service and is also used as the YELLOW key in the menus. UHF key UHF Sets the UHF menu and is used as the BLUE key in the menus. Time key Displays the curr
Inhaltszusammenfassung zur Seite Nr. 3
Remote Control Unit Standby key P+ / P- Programme Up/Down key Switches between Operation Used to tune to the next or previous and Standby mode. service. Used to move up or down a page in the menu mode. TV/SAT This key is not available for F1-ACE. Help key ? 09 ~ Numeric key Displays the Help box on the screen. Used to select the service and enter the channel information and PIN Code. Recall key RCL Selects the previously viewed channel. TV/Radio key Receiver Switches: TV/ Radio receive mode EP
Inhaltszusammenfassung zur Seite Nr. 4
Specification 2. STB’S Specification The concept OSD is for On-Screen-Display Tuner & Channel ; means that Menu displays Input Connector : F-type, IEC 169-24, Female on the Screen of TV. Frequency Range : 950 MHz to 2150 MHz Input Impedance : 75Ω unbalanced Signal Level : -25 to -65dBm IF Frequency : 480 MHz IF Band width : 36 MHz LNB Power & Polarisation : Vertical : +13.5V Horizontal : +18V Current : 500mA Max Overload Protection 22 KHz Tone : Frequency : 2
Inhaltszusammenfassung zur Seite Nr. 5
Specification A/V & Data In/Out VIDEO : RCA/Cinch Video Output(CVBS) You can use a special antenna switch AUDIO R/L : Cinch volume and Mute Control with DiSEqC commands. (Resolution : 20bit DAC, max 2 Vrms) When changing channel from ASTRA RS232C : Transfer rate 115,200 bps to EUTELSAT for example, a DiSEqC 9 pin D-sub Type command is sent with the 22KHz tone through the antenna cable. The antenna switch will change
Inhaltszusammenfassung zur Seite Nr. 6
Support & Copyright First and foremost, our knowledge of the set-top box marketplace along with technical expertise differentiates HUMAX. Moreover, we maintain very close working relationships with our customers. We take a highly disciplined engineering approach to product design, manufacture, testing, acceptance, and to technical and maintenance support. We conduct comprehensive testing of the units, provide complete documentation and support, and deliver the highest quality, most consistent
Inhaltszusammenfassung zur Seite Nr. 7
Safety This STB has been manufactured to satisfy the international safety standards. Please read the following recommended safety precautions carefully. MAINS SUPPLY : 190 ~ 250V AC 50/60Hz. OVERLOADING : Do not overload wall outlets, extension cords or adapters as this can result in fire or electrical shock. LIQUIDS : Keep liquids away from the STB. CLEANING : Disconnect the STB from the wall socket before cleaning it. Use a cloth lightly dampened with water (no solvents) to clean
Inhaltszusammenfassung zur Seite Nr. 8
STB Connection There are several ways of connecting the STB to your existing Audio/TV system. We recommend using one of the following set-up for best results: Set-up 1 TV only Connect one end of RCA/Cinch cable to the RCA/Cinch socket on the back of the STB and the other end to a RCA/Cinch socket on your TV. If your TV doesn’t have a RCA/Cinch socket, connect one end of RF cable to the RF OUT on the back of the STB and the other end to a RF input socket on your TV. Finally connect the coax
Inhaltszusammenfassung zur Seite Nr. 9
STB Connection Set-up 2 With Hi Fi System Connect an RCA/Cinch stereo cable from the AUDIO L, R sockets on the back of the STB to the LINE, AUX, SPARE OR EXTRA input sockets on your Hi Fi System. 8
Inhaltszusammenfassung zur Seite Nr. 10
STB Connection Set-up 3 TV with Terrestrial antenna Connect one end of RCA/Cinch cable to the RCA/Cinch socket on the back of the STB and the other end to a RCA/Cinch socket on your TV. If your TV doesn’t have a RCA/Cinch socket, connect one end of RF cable to the RF OUT on the back of the STB and the other end to a RF input socket on your TV. Connect one end of RF cable to the RF IN on the back of the STB and the other end to a terrestrial antenna connection or the socket for public antenna o
Inhaltszusammenfassung zur Seite Nr. 11
STB Connection Set-up 4 TV with Motorised System (DiSEqC 1.2) Connect one end of RCA/Cinch cable to the RCA/Cinch socket on the back of the STB and the other end to a RCA/Cinch socket on your TV. If your TV doesn’t have a RCA/Cinch socket, connect one end of RF cable to the RF OUT on the back of the STB and the other end to a RF input socket on your TV. Connect one end of your coaxial cable to the LNB IN connector on the STB and the other end to the REC or Receiver connector on the DiSEqC 1.2
Inhaltszusammenfassung zur Seite Nr. 12
Reference Set-up 5 TV with Motorised System and Positioner Connect one end of RCA/Cinch cable to the RCA/Cinch socket on the back of the STB and the other end to a RCA/Cinch socket on your TV. If your TV doesn’t have a RCA/Cinch socket, connect one end of RF cable to the RF OUT on the back of the STB and the other end to a RF input socket on your TV. Connect the coaxial cable from the LNB of your motorised system to the LNB IN socket on the STB. Connect the motor cables to your positioner. (p
Inhaltszusammenfassung zur Seite Nr. 13
Guide of Functions LED of STB The message of the LEDs(Lighting-Emitting Diode) on the STB is explained as below. Upgrade via Satellite and Personal Computer To maintain the STB up-to-date, it will be possible to upgrade the software of the STB via satellite and personal computer. New versions of the software may include new or improved functions for the current one. If you want to download and upgrade the software via satellite, first of all tune your signal to ASTRA Satellite. When the STB
Inhaltszusammenfassung zur Seite Nr. 14
Guide of Functions Information Box (I-Plate) I-Plate displays when the i key is pressed or when the service is changed. It shows the service part and event part. When you move to another service, the I-Plate should be displayed automatically. The time the I-Plate is displayed on screen is controlled in the Other Setting menu. SERVICE PART The contents of the service part are as follows: - I-Plate Icon, Current Time - Service Name, Service Number and Service Icon - Subtitle( ), Telet
Inhaltszusammenfassung zur Seite Nr. 15
Guide of Functions Service Change To change the service, enter the number by using the 0 ~ 9 keys. It is also possible to change the service by using the P+/P- keys, / keys, Recall, Service list or EPG mode. To switch between the video and audio service, press the key. To select the previously viewed service list, press the RCL key in the normal A/V playback mode. Volume Control To control the volume, press the / keys. Select the mute mode by pressing the key and t
Inhaltszusammenfassung zur Seite Nr. 16
Guide of Functions Subtitle The display of the subtitle are tramitted from the EBU teletext specification and DVB Bitmap. Press the key to bring up the subtitle language list for the current service. Use the / keys to select the desired language. Then press the OK key to select the highlighted language, the subtitles will now be displayed. To cancel the subtitle mode, press the key or EXIT key again. Teletext To view the teletext, you have to use your TV remote control
Inhaltszusammenfassung zur Seite Nr. 17
Guide of Functions In the advanced Service List, it is possible to list All or Favourite service list by using the colour keys as follows: i (red) key - Service List All (green) key - Favourite A. Service All The / keys moves the highlight bar to the previous or next service, using the / keys moves the higlight bar forwards or backwards by 10 services. Select the desired move the cursor service by using the / / / keys. Press the OK key previous or next page to view t
Inhaltszusammenfassung zur Seite Nr. 18
Guide of Main Menu Main Menu The contents of main menu are as follows: move the cursor open the sub menu go to the selected menu exit from the menu screen page 18~19 1. TV GUIDE It shows the programme information and the timer programming process of the service. Select the TV Guide mode by pressing the EPG key in the Video/Audio playback mode. page 19 2. PARENTAL CONTROL It is possible to control access to certain programmes by set- ting the parental level or changing the PIN code. To relea
Inhaltszusammenfassung zur Seite Nr. 19
Guide of Main Menu 1. TV GUIDE You can set the reservation and view the programme (event name) for each service in the TV Guide mode. To access this mode press the EPG key or select the TV Guide in the Main Menu. Change between the TV Guide and Radio Guide by pressing the key. In the TV guide mode, you can select between four different modes. i (red) key - Shows Now or Next programmes for the day. (green) key - Shows programme list for one week. (yellow) key - Shows the Reser
Inhaltszusammenfassung zur Seite Nr. 20
Guide of Main Menu TV GUIDE-Quick mode. This mode shows in the A/V playback mode. The red line represents the current time and shows the programme progress status using a Black/White progress bar. The time range of the bar is made up from the past one hour and the next two hours. 2. PARENTAL CONTROL In the Parental Control Menu, you can set the censorship classification or change the PIN code. Enter the PIN Code 0 0 0 0 . Censorship classification : Set the parental level. If the level disp
