Bedienungsanleitung Metra Electronics 99-7864

Inhaltszusammenfassung zur Seite Nr. 1

INSTALLATION INSTRUCTIONS FOR PART 99-7864
APPLICATIONS
Honda Accord
2003-2007
(Equipped with Single Zone Climate Controls)
99-7864
KIT FEATURES
• DIN Radio Provision
• ISO Radio Provision
KIT COMPONENTS
A) Radio/Climate Control Housing B) ISO Brackets C) ISO Trim Plate D) PPH-1034 Screws
C D
B
WIRING AND ANTENNA CONNECTIONS (Sold Separately)
A
WIRING HARNESS:
• 70-1721 - Honda/Acura Harness 1998-up
• 70-78640Z - Accord Dual Zone Eliminator Harness 2003-07
ANTENNA ADAPTER:
Not Required
T

Inhaltszusammenfassung zur Seite Nr. 2

99-7864 TABLE OF CONTENTS Dash Disassembly - Honda Accord 2003-2007 .... ........ ........ ....... ........ .. .1,2 Kit Assembly - DIN Radio Provision ..... ........ ........ ....... ........ ... ..... . 3 - ISO Radio Provision ..... ........ ........ ....... ........ ... ..... . 4 Final Assembly . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 *Note: Refer also to the instructions included with the aftermarket radio. NOTE: To adapt dual zone climate contr

Inhaltszusammenfassung zur Seite Nr. 3

D D D D D D R R R N N N 99-7864 DASH DISASSEMBLY HONDA ACCORD 2003-2007 A 1 Disconnect the negative battery- terminal to prevent an accidental short circuit. 2 Unsnap and remove shift lever trim ring. (Figure A) Unsnap coin tray/ashtray from 3 assembly and remove. Rubber cover may come out first but entire assembly must be removed to access screws below. (Figure B) B 4 Remove (2) Phillips screws from under coin tray/ashtray and remove entire assembly. (Figure C) Continue to kit assembly. C 1

Inhaltszusammenfassung zur Seite Nr. 4

D D P R N 99-7864 DASH DISASSEMBLY HONDA ACCORD 2003-2007 *Note: Refer also to the instructions included with the aftermarket radio. D 5 Remove (2) Phillips screws from bottom of pocket assembly and unsnap and remove. (Figure D) 6 Remove (2) Phillips screws facing up under radio/climate control assembly.) (Figure E) 7 Push and hold the hazard button down. Carefully insert a flat blade screwdriver into the slot below the button and push down to release the center clip. (Figure F) 8 Unsnap and r

Inhaltszusammenfassung zur Seite Nr. 5

99-7864 KIT ASSEMBLY DIN RADIO PROVISION *Note: Refer also to the instructions included with the aftermarket radio. A 1 Snap the DIN cage into the Radio Housing and secure by bending the metal locking tabs down. (Figure A) 2 Slide the aftermarket radio into the cage and secure. (Figure B) Continue to final assembly. Programming: In order to adjust the 99-7864 to the different types of radios available in the Honda Accord, B the 99-7864 has a program fea- ture. 4 DOOR SEDAN ONLY: To program the

Inhaltszusammenfassung zur Seite Nr. 6

99-7864 KIT ASSEMBLY ISO RADIO PROVISION *Note: Refer also to the instructions included with the aftermarket radio. A 1 Mount the ISO Brackets to the head unit with the screws supplied with the unit. (Figure A) 2 Slide the head unit into the radio opening until the side clips engage. Snap the Trim plate into the Radio Housing. (Figure B) NOTE: When reinstalling the screws into the bottom of the 99-7864 use the (2) supplied Phillips screws instead of the factory screws removed in step 5 in B Da

Inhaltszusammenfassung zur Seite Nr. 7

99-7864 FINAL ASSEMBLY FINAL ASSEMBLY A (A) Strip wire ends back 1/2" B B) Twist ends together C) Solder D) Tape C D 1 Locate the factory wiring harness in the dash. Metra recommends using the proper mating adapter and making connections as shown. (Isolate and individ- ually tape off the ends of any unused wires to prevent electrical short circuit.) 2 Re-connect the negative battery terminal and test the unit for proper operation. 3 Reassemble radio and dash assemblies in reverse order of disas

Inhaltszusammenfassung zur Seite Nr. 8

99-7864 INSTRUCTIONS 1-800-221-0932 www.metraonline.com REV. 05/04/09 © COPYRIGHT 2004-2009 METRA ELECTRONICS CORPORATION INST99-7864