Inhaltszusammenfassung zur Seite Nr. 1
USER’S MANUAL
A42W64AT4
Thank you very much for choosing the Envision Series Plasma TV.
We recommend that you take a few minutes to read carefully through this manual before
installing and using the TV.
Inhaltszusammenfassung zur Seite Nr. 2
CONTENT IMPORTANT SAFETY INSTRUCTIONS .....................................................................................1 Precautions and Reminders……………………………………………………………………………..2 Features and Function………………………………………………………….…………………….….4 Front Panel Control……………………………………………………………………………………….5 Basic Installation…………………………………………………………………………………………..6 Connection to other equipment………………………………………………………………………….7 Remote Control Function ......................................................
Inhaltszusammenfassung zur Seite Nr. 3
IMPORTANT SAFETY INSTRUCTIONS Read before operating equipment 1. Read and follow all instructions. 14. Tilt/Stability- All televisions must comply with recommended 2. Do not operate this apparatus near water. international safety standards for tilt and stability properties of its 3. Do not install near any heat sources such as radiators, heat registers, cabinet design. stoves, or other apparatus (including amplifiers) that produce heat. • Do not compromise these design standa
Inhaltszusammenfassung zur Seite Nr. 4
Precautions and Reminders Do not place unit on uneven surfaces. Do not place the TV in confined spaces or in a box when using it. Unplug immediately if there is any malfunction, Unplug immediately if other foreign materials like no video, no audio, smoke or a bad odor. are put inside TV box or if the TV fell down. Do not throw any object like metals or flammable materials into the TV set. Prohibit/Avoid opening T
Inhaltszusammenfassung zur Seite Nr. 5
Precautions and Reminders DO NOT use liquid cleansers or aerosol Avoid direct sunlight, dusty, high humidity and cleansers to clean the plasma display. Dilute a smoky areas. neutral detergent with water and wipe with a soft cloth or gently clean with some absorbent cotton. Remember to unplug the AC mains cord before cleaning the display. Make sure to unplug the unit when not in use Call service personnel to clean the internal part for a long period of time (2 days). of the TV o
Inhaltszusammenfassung zur Seite Nr. 6
Features and Function 42 inch（107cm）Large Screen Flat Panel Plasma Display Panel Resolution: WVGA 852 x 480 Pixels 2 MAX Brightness of Panel: 1500 Cd/m MAX Contrast Ratio of Panel: 10000:1 View Angle: Greater than 160° Internal TV Tuner, Air：69 channels Cable：135 channels Frequency Range：55.25MHz to 859.25MHz ATSC receiver, MPEG-2 decoder NTSC receiver, Video decoder Dual Video, Dual S-Video Dual Y Pb Pr （480i, 480P, 720P, 1080i）HDTV Ready PC D-SUB 15Pin INPUT D-SUB V
Inhaltszusammenfassung zur Seite Nr. 7
Front Panel Control MENU MODE - CH + - VOL + ⑦ ⑥ ⑤ ④ ③ ② ① Mode: Press to select input signal modes or use as Enter in Menu operation. ① MODE Menu: Press to enter Menu or exit Menu. ② MENU Left: Press to decrease the sound volume level or move Left in Menu operation. ③- VOL + Right: Press to increase the sound volume level or move Right in Menu operation. Down: Press to select the next lower Programme numb
Inhaltszusammenfassung zur Seite Nr. 8
Basic Installation 1. Connect TV Cable and Power Cord to this PDP TV Set. 2. Plug Power Cord to your home power outlet. 3. Check front panel LED for proper power connection: Blue color indicates this TV set is powered on; Red color indicates this TV set is in standby state. 4. Push POWER KEY on Remote Control or Power key on POWER KEY Front panel controls to switch the TV from stand by state to ON state.
Inhaltszusammenfassung zur Seite Nr. 9
Connection to other equipment Please connect this TV Set to other equipment as picture below. You may have many types of equipment as: DVD, VCD, VCR, Set Top Box, X-Box and so on. (View from back of the TV set,left to right) INPUT CONNECTION OF VIDEO SIGNAL(DVD/VCD/VCR) s-video Y R W B AV1-INPUT s-video Y R W 7
Inhaltszusammenfassung zur Seite Nr. 10
Connection to other equipment We have 2 component signal input jacks: Y Cb Cr and Y Pb Pr. The R / L is Audio input for every Y Cb Cr and Y Pb Pr. If your DVD or Set Top Box have Y Cb Cr or Y Pb Pr output, you can connect it to Y Cb Cr or Y Pb Pr input jack. And select to Y Cb Cr or Y Pb Pr source input. （Some DVD or Set Top Box need to set to Y Cb Cr or Y Pb Pr output） Notice: If you see that display abnormality in screen, you need to check the cable connection an
Inhaltszusammenfassung zur Seite Nr. 11
TS M Menu Remote Control Function “Wide Mode” “POWER” Normal, Zoom ,Wide, Cinema The TV Set turn on /turn off key display select POWER EPG Wide Mode “Video” “EPG” AV1 CVBS Rear /AV1 S-Video Video Digital TV Display the state, source Rear/ AV2 CVBS Side/ AV2 S-Video Side / AV3 component 1/ SLEEP “TV” AV4 component 2 TV source select, into TV state “Digital” Up “SLEEP ” VGA/DVI source input Select timer into power down left Enter right state. off→30→60→9
Inhaltszusammenfassung zur Seite Nr. 12
OSD Menu Descriptions Main Menu 1. Press “MENU” key on remote control or front panel controls to bring up Main Menu. 2. Press “ ” or “ ” to move the cursor up and down the sub menu list. 3. Press “ ” or “ ” to select sub menu item. 4. Press "Enter" to enter sub-item then use “ ” or “ ” to adjust. Setup Menu 1. Tuning Band: Select TV signal source between Air and Cable. Select Cable if you are connecting to a cable box and select Air if you
Inhaltszusammenfassung zur Seite Nr. 13
OSD Menu Descriptions Video Menu . 1. Press “ ” or “ ” to move the cursor up or down the sub-item list. 2. Press "Enter" to enter the highlighted sub-item menu. 3. Press “ ” or “ ” to adjust the value of the sub-item. 4. Press "Enter" again to exit the sub-item. Contrast: Contrast adjustment, 0 ~ 100. Brightness: Brightness adjustment, 0 ~ 100. Color: Color chroma adjustment, 0 ~ 100. Tint: Tint adjustment, 0 ~ 100. Aspect Ratio: Asp
Inhaltszusammenfassung zur Seite Nr. 14
OSD Menu Descriptions Feature Menu 1. Press “ ” or “ ” to move the cursor up or down the sub-item list. 2. Press "Enter" to enter the highlighted sub-item menu. 3. Press “ ” or “ ” to adjust the value of the sub-item. 4. Press "Enter" again to exit the sub-item. Time Set : The default time when you first set up theTV is 12:00 midnight. The internal clock starts from 12:00am. In the time set menu, first select the time zone
Inhaltszusammenfassung zur Seite Nr. 15
OSD Menu Descriptions Closed Captions section 1. Press “CC” key on remote control to select closed captions mode. NTSC TV: Off..CC1 ..CC2 .. … ATSC TV: Off ..CS1 ..CS2.. … 2. Select desired closed caption mode. CC1 3.Closed captioning for analog NTSC channels is transmitted NTSC TV as CC1/CC2/CC3/CC4.Closed captioning for digital channels is transmitted as CS1/CS2/CS3 /CS4/CS5/CS6 or occasionally CC1/CC2/CC3/CC4. You need to select the option you want for
Inhaltszusammenfassung zur Seite Nr. 16
Specifications Item Specification Screen size 42 inch plasma display panel Aspect 16:9 Display pixels 852 x 480 (WVGA) Panel Effective display size 932mm x 532mm Spec Number of color 16.7 million colors Contrast Ratio 10000:1 (in dark room) Peak brightness 1500 cd/㎡ TV Tuning 1 Tuners, Air:69 channels Cable:135 channels Sound system M TV Mode Color system ATSC / NTSC Video RCA x 1 NTSC Audio: L/R x 1 AV1 ( S_Video/Video) S-Video1 x 1 NTSC Video RCA x 1 NTSC Audio: L/
Inhaltszusammenfassung zur Seite Nr. 17
Troubleshooting Symptoms Checks •Please ensure the antenna is properly connected. Picture freezes in antenna mode. The TV does not react to remote •Please switch off the mains and switch on again. controller commands. •Re-install the channels if needed. •The TV is trying to read the HDCP code sent by the set top Picture breaks up in DVI mode, especially when a set top box is box. connected. •Please switch off the set top box and switch on again. •The signal could be weak.
Inhaltszusammenfassung zur Seite Nr. 18
Troubleshooting The plasma TV panel is manufactured using an extremely Some parts of the high level of precision technology, however, sometimes some parts of the screen may be missing picture elements screen do not light up or have luminous spots. This is not a malfunction. Do not allow a still picture to be displayed for an extended period, as this can cause a permanent after-image to After-images appear remain on the Plasma TV. Examples of still pictures include logos, vid
Inhaltszusammenfassung zur Seite Nr. 19
Envision Peripherals Inc. 47490 Seabridge Dr. Fremont, CA 94538 www.AOCdisplay.com Tech Support: 1-888-662-9888
