Inhaltszusammenfassung zur Seite Nr. 1
User’s Guide
W1942SM
W2042SM
W2242SM
Make sure to read the Important Precautions before using the product.
Keep the User's Guide(CD) in an accessible place for future reference.
See the label attached on the product and give the information to your
dealer when you ask for service.
Inhaltszusammenfassung zur Seite Nr. 2
Important Precautions This unit has been engineered and manufactured to ensure your personal safety, however improper use may result in potential electrical shock or fire hazards. In order to allow the proper operation of all safeguards incorporated in this display, observe the following basic rules for its installation, use, and servicing. On Safety Use only the power cord supplied with the unit. In case you use another power cord, make sure that it is certified by the applicable national stan
Inhaltszusammenfassung zur Seite Nr. 3
Important Precautions On Installation Do not allow anything to rest upon or roll over the power cord, and do not place the display where the power cord is subject to damage. Do not use this display near water such as near a bathtub, washbowl, kitchen sink, laundry tub, in a wet basement, or near a swimming pool. Displays are provided with ventilation openings in the cabinet to allow the release of heat generated during operation. If these openings are blocked, built-up heat can cause failures wh
Inhaltszusammenfassung zur Seite Nr. 4
Connecting the Display Before setting up the monitor, ensure that the power to the monitor, the computer system, and other attached devices is turned off. Connecting the stand 1. Place the monitor with its front facing downward on a soft cloth. 2. Assemble the Stand Body into the product in the correct direction as shown in the picture. Make sure you push it until you hear it “click”. Hinge Body Stand Body 3. Assemble the Stand Base(Front, Rear) into the Stand Body in the correct direction. St
Inhaltszusammenfassung zur Seite Nr. 5
Connecting the Display Disassembling the stand 1. Put a cushion or soft cloth on aflat 2. Place the monitor face Down on surface. the cushion or soft cloth. 3. Change your lock on the product as it follows and turn it in the arrow direction. If you can't release the stand base even the locking knob is at a release position, Please push the indicated knob down and retry it. 4. Pull out the Stand to remove. A4
Inhaltszusammenfassung zur Seite Nr. 6
Connecting the Display 5. Pushing the PUSH button, Take the stand base from stand body. Warning: You can hurt your finger. Good Position Bad Position Before setting up the monitor, ensure that the power to the monitor, the computer system, and other attached devices is turned off. Positioning your display 1. Adjust the position of the panel in various ways for maximum comfort. Tilt Range : -5˚~20˚ 20 Ergonomic It is recommended that in order to maintain an ergonomic
Inhaltszusammenfassung zur Seite Nr. 7
Connecting the Display Using the Computer 1. Make sure to turn off the computer and product. Connect the cable as below sketch map form 1 to 2 . A Connect Audio Cable B Connect Dsub Cable (PC) C Connect Dsub Cable (Mac) Power Cord Analog signal Audio signal Headphone/Earphone Input Wall-outlet type Automatically mutes the speaker volume when the headphones are plugged in. PC-outlet type Mac adapter For Apple Macintosh use, a separate plug adapter is needed to change the 15 pin high density (
Inhaltszusammenfassung zur Seite Nr. 8
Control Panel Functions Front Panel Controls Control Function MUTE Button Use this button to mute the speaker volume. Use this button to save the adjusted speaker volume. Use this button to enter or exit the On Screen Display. . MENU Button OSD LOCKED/UNLOCKED This function allows you to lock the current control settings, so that they cannot be inadvertently changed. Press and hold the MENU button for several seconds. The message "OSD LOCKED" should appear. You can unlock the OSD controls at a
Inhaltszusammenfassung zur Seite Nr. 9
Control Panel Functions Control Function Use these buttons to select or adjust functions in the On Screen Display. For more information, refer to page A15. VOLUME Use these buttons to select or adjust functions in the On Screen Display. Use buttons to decrease or increase the speaker volume. Use this button to enter a selection in the On Screen AUTO/SET Display. Button AUTO IMAGE ADJUSTMENT When adjusting your display settings, always press the AUTO/SET button before entering the On S
Inhaltszusammenfassung zur Seite Nr. 10
On Screen Display (OSD) Control Adjustment Screen Adjustment Making adjustments to the image size, position and operating parameters of the display is quick and easy with the On Screen Display Control system. A short example is given below to familiarize you with the use of the controls. The following section is an outline of the available adjustments and selections you can make using the OSD. NOTE Allow the display to stabilize for at least 30 minutes before making image adjustments. To make a
Inhaltszusammenfassung zur Seite Nr. 11
On Screen Display(OSD) Selection and Adjustment The following table indicates all the On Screen Display control, adjustment, and setting menus. Main menu Sub-menu A Reference BRIGHTNESS PICTURE To adjust the brightness, contrast and gamma of the CONTRAST screen GAMMA sRGB To customize the color of COLOR PRESET 6500K the screen 9300K RED GREEN BLUE To adjust the position of the HORIZONTAL screen VERTICAL CLOCK TRACKING To improve the clarity and PHASE stability of the sc
Inhaltszusammenfassung zur Seite Nr. 12
On Screen Display(OSD) Selection and Adjustment You were introduced to the procedure of selecting and adjusting an item using the OSD system. Listed below are the icons, icon names, and icon descriptions of the all items shown on the Menu. Press the MENU Button, then the main menu of the OSD appears. Main Menu MENU : Exit - + : Adjust (Decrease/Increase) SET : Enter : Select another sub-menu Button Tip Menu Name Sub-menus Icons NOTE OSD (On Screen Display) menu languages on the m
Inhaltszusammenfassung zur Seite Nr. 13
On Screen Display(OSD) Selection and Adjustment Main menu Sub menu Description PICTURE PICTURE BRIGHTNESS To adjust the brightness of the screen. To adjust the contrast of the screen. CONTRAST Set your own gamma value. : -50/0/50 GAMMA On the monitor, high gamma values display whitish images and low gamma MENU : Exit values display high contrast images. : Decrease - + : Increase SET : Select another sub-menu COLOR COLOR Select the screen color. PRESET • sRGB: Set the screen color to fit t
Inhaltszusammenfassung zur Seite Nr. 14
On Screen Display(OSD) Selection and Adjustment Main menu Sub menu Description TRACKING TRACKING HORIZONTAL To move image left and right. VERTICAL To move image up and down. CLOCK To minimize any vertical bars or stripes visible on the screen background. The horizontal screen size will also change. PHASE To adjust the focus of the display. This item allows you to remove any horizontal noise and clear or sharpen MENU : Exit the image of characters. - : Decrease + : Increase SET : Select anot
Inhaltszusammenfassung zur Seite Nr. 15
On Screen Display(OSD) Selection and Adjustment Main menu Sub menu Description LANGUAGE To choose the language in which the SETUP control names are displayed. SETUP OSD To adjust position of the OSD window POSITION on the screen. WHITE If the output of the video card is different BALANCE the required specifications, the color level may deteriorate due to video signal distortion. Using this function, the signal level is adjusted to fit into the standard output level of the video card in order to
Inhaltszusammenfassung zur Seite Nr. 16
On Screen Display(OSD) Selection and Adjustment The OSD screen will appear when you touch the button on the left side of the monitor. Menu Name Icons Sub-menu Name Main menu Sub menu Description This feature lets you easily select the best desired MOVIE image condition optimized to the environment INTERNET (ambient illumination, image types etc). MOVIE: For animation images in videos or movies INTERNET: For text images (Word processing etc.) USER User You can manually adjus
Inhaltszusammenfassung zur Seite Nr. 17
Troubleshooting Check the following before calling for service. No image appears No image appears ● Is the power cord of the • Check and see if the power cord is connected display connected? properly to the power outlet. ● Is the power on and the • Adjust the brightness and the contrast. power indicator blue or green? ● Is the power indicator • If the display is in power saving mode, try moving amber? the mouse or pressing any key on the keyboard to bring up the screen. • Try to turn on the PC.
Inhaltszusammenfassung zur Seite Nr. 18
Troubleshooting Display image is incorrect ● Display Position is • Press the AUTO/SET button to automatically incorrect. adjust your display image to the ideal setting. If the results are unsatisfactory, adjust the image position using the H position and V position icon in the on screen display. • Press the AUTO/SET button to automatically ● On the screen adjust your display image to the ideal setting. background, vertical If the results are unsatisfactory, decrease the bars or stripes are vert
Inhaltszusammenfassung zur Seite Nr. 19
Troubleshooting Display image is incorrect ● The screen color is • Check if the signal cable is properly connected mono or abnormal. and use a screwdriver to fasten if necessary. • Make sure the video card is properly inserted in the slot. • Set the color setting higher than 24 bits (true color) at Control Panel - Settings. • Check if the screen is set to interlace mode and if ● The screen blinks. yes, change it to the recommend resolution. Have you installed the display driver? ● Have you insta
Inhaltszusammenfassung zur Seite Nr. 20
Specifications W1942SM Display 19 inches (48.14 cm) Flat Panel Active matrix-TFT LCD Anti-Glare coating 19 inches viewable 0.285*0.285 mm pixel pitch Horizontal Freq. 28 - 83 kHz (Automatic) Sync Input Vertical Freq. 56 - 75 Hz (Automatic) Input Form Separate TTL, Positive/Negative SOG (Sync On Green) Signal Input 15 pin D-Sub Connector Video Input Input Form RGB Analog (0.7 Vp-p/ 75 ohm) Resolution Max VESA 1440 x 900 @ 75 Hz
