Inhaltszusammenfassung zur Seite Nr. 1
Offset head dual chuck
tire inflat Or
90670
set up and Operating instructiOns
Visit our website at: http://www.harborfreight.com
read this material before using this product.
failure to do so can result in serious injury.
sa Ve this manual.
© ®
Copyright 2003, 2009 by Harbor Freight Tools . All rights reserved. No portion of this manual or
any artwork contained herein may be reproduced in any shape or form without the express written
consent of Harbor Freight Tools. Diagrams within this
Inhaltszusammenfassung zur Seite Nr. 2
nOtice is used to sa Ve this manual address practices Keep this manual for the safety not related to personal injury. warnings and precautions, assembly, cautiOn, without operating, inspection, maintenance and the safety alert cleaning procedures. Write the product’s symbol, is used to address serial number in the back of the manual practices not related to near the assembly diagram (or month personal injury. and year of purchase if product has no number). Keep this manual and t
Inhaltszusammenfassung zur Seite Nr. 3
medication. A moment of inattention dangerous in the hands of untrained while operating the tool increases the users. risk of injury to persons. e. maintain the tool with care. A b. avoid unintentional starting. Be properly maintained tool reduces sure the t rigger is off before the risk of binding and is easier to connecting to the air supply. Do control. not carry the tool with your finger on f. check for any condition that the Trigger or connect the tool to the affects the tool’s opera
Inhaltszusammenfassung zur Seite Nr. 4
Such gases are capable of explosion Specific Safety Instructions and serious injury to persons. 1. The warnings and precautions discussed in this manual cannot sa Ve these cover all possible conditions and instructiOns. situations that may occur. It must be understood by the operator that common sense and caution are sYmBOls and specific factors which cannot be built into this safetY instructiOns product, but must be supplied by the operator. Symbol Definitions 2. Obey the manual fo
Inhaltszusammenfassung zur Seite Nr. 5
specificatiOns initial tOOl set up/ assemBl Y Operating Air Pressure 120 PSI read the entire Measuring Air 10 - 120 PSI in 2 lb. impOrtant safetY Pressure Increments infOrmatiOn section Air Inlet 1/4” -18 NPT at the beginning of this 6 - 60 PSI in 2 lb. manual including all text Pocket Tire Gauge Increments under subheadings therein before set up or use of this components and controls product. Tire Pressure unpacking Hose (2) Release Pin Pocket When unpacking, make sure that Tire th
Inhaltszusammenfassung zur Seite Nr. 6
note: The air hose must be long enough coupler coupler to reach the work area with enough plug plug extra length to allow free movement t ool while working. Quick 3. Release the Trigger. Close the in-line air hose coupler on reel safety valve between the compressor and the tool. Valve filter 4. Turn on the air compressor according to the manufacturer’s directions and air compressor allow it to build up pressure until it Quick cycles off. coupler regulator with pressure gauge 5. Adju
Inhaltszusammenfassung zur Seite Nr. 7
Inflator, unthread the valve stem cap Operating instructiOns from the tire you wish to inflate, then push the Tire Chuck (1) onto the read the entire valve stem for outside tires, or pull impOrtant safetY infOrmatiOn section onto inside tire valve. Make sure that at the beginning of this the Tire Chuck fits snugly onto the manual including all text valve stem, holding it in place while adding or adjusting tire air pressure. under subheadings therein before set up or use of this note
Inhaltszusammenfassung zur Seite Nr. 8
Trigger and press the Air Release air occurs, have the problem button while the Tire Chuck is on the corrected before further use. valve stem. Hold for a short period tO preVent explOsiOn: of time, then release, and check the lubricate the tool only tire air pressure on the Stick Gauge. with specified lubricants. Repeat as needed to achieve the lubricate the air inlet using desired value. only pneumatic tool oil. 6. When the tire is inflated to the proper Other lubricants may damag
Inhaltszusammenfassung zur Seite Nr. 9
t roubleshooting problem possible causes likely solutions Decreased 1. Not enough air pressure and/ 1. Check for loose connections and make sure output. or air flow. that air supply is providing enough air flow (CFM) at required pressure (PSI) to the tool’s air inlet. do not exceed maximum air pressure. 2. Obstructed trigger. 2. clean around trigger to ensure free movement. 3. Damaged hose. 3. Have repaired or replaced by a qualified technician. Chuck valve stuck. Replace Chuck. Failure
Inhaltszusammenfassung zur Seite Nr. 10
limited 1 Year W arrantY Harbor Freight Tools Co. makes every effort to assure that its products meet high quality and durability standards, and warrants to the original purchaser that this product is free from defects in materials and workmanship for the period of one year from the date of purchase (90 days if used by a professional contractor or if used as rental equipment). This warranty does not apply to damage due directly or indirectly, to misuse, abuse, negligence or accidents, repai
