Inhaltszusammenfassung zur Seite Nr. 1
AR450S SECURITY APPLIANCE
QUICK INSTALL GUIDE
Software Release 2.5.2
Inhaltszusammenfassung zur Seite Nr. 2
AR450S Quick Install Guide Document Number C613-04045-01 REV A. Copyright © 2003 Allied Telesyn International, Corp. 19800 North Creek Parkway, Suite 200, Bothell, WA 98011, USA. All rights reserved. No part of this publication may be reproduced without prior written permission from Allied Telesyn. Allied Telesyn International, Corp. reserves the right to make changes in specifications and other information contained in this document without prior written notice. The information provided here
Inhaltszusammenfassung zur Seite Nr. 3
Quick Install Guide 3 Documentation Roadmap AR450S Router General Customer Support Visit www.alliedtelesyn.co.nz for AR400 Series Safety and Statutory Information the latest documentation, FAQ, AR450S Quick Install Guide and support information AR400 Series User Guide AR400 Series Software Reference AR Router Hardware Reference Printed Acrobat PDF Website Models Covered By This Guide This Quick Install Guide includes information on the following model: ■ AR450S Quick Install Guide updates can b
Inhaltszusammenfassung zur Seite Nr. 4
4 AR450S Router Selecting a Site The router should be installed on a level surface such as a desktop or bench. When installing the router, choose a site that: ■ Allows adequate airflow around the router and its vents. ■ Is free of dust and moisture. ■ Will maintain an ambient temperature range of 0 to 40º C (32 to 104º F) and a humidity range of 5 to 95% non-condensing. ■ Has a reliable and earthed (grounded) power supply circuit, preferably dedicated and filtered. ■ Does not expose cabling
Inhaltszusammenfassung zur Seite Nr. 5
Quick Install Guide 5 5. Apply power to the router. Fit the power cord retaining clip to the AC power inlet on the router’s rear panel. Connect the provided power cord to the AC power inlet and clip it in place. Switch the router’s power switch to the ON position. The Power LED will light continuously and the System LED will flash briefly. The Port LEDs may also light briefly. If the LEDs fail to light, the most likely cause is that the router is not receiving power. Check that The power
Inhaltszusammenfassung zur Seite Nr. 6
6 AR450S Router Set the communication parameters on your terminal or terminal emulation program to: Baud rate: 9600 Data bits: 8 Parity: None Stop bits: 1 Flow control: Hardware See the AR Router Hardware Reference for more information on configuring emulation software. 2. Log in and set the password. The log in prompt appears on the terminal or PC. If the log in prompt doesn’t appear, press [Enter] two or three times. When the router boots for the first time it automatically creates
Inhaltszusammenfassung zur Seite Nr. 7
Quick Install Guide 7 1. Connect the PC to a router switch port. The PC can be connected directly, or through your LAN. To connect the PC directly to the router, use a straight-through Ethernet cable to connect an Ethernet card on the PC to any one of the router’s switch ports. Note the PC’s IP address and mask. To connect via a LAN, use a straight-through Ethernet cable to connect the router’s switch port(s) to the device(s) on the LAN. Select the LAN PC from which you wish to configure the
Inhaltszusammenfassung zur Seite Nr. 8
8 AR450S Router 4. Assign an IP address to VLAN1. Assign the VLAN1 interface an IP address in the subnet that the PC uses, using the command: ADD IP INTERFACE=vlan1 IP=ipaddress MASK=mask 5. Browse to the GUI. If you access the Internet through a proxy server, set your browser to bypass the proxy for the IP address you just assigned to the VLAN1 interface. Point your web browser at the IP address of the VLAN interface. 6. Log in and set the password. At the log in prompt, enter the log in na
Inhaltszusammenfassung zur Seite Nr. 9
Quick Install Guide 9 2. Connect to the WAN. If you intend to use a firewall, configure it before you activate the WAN link. Once initial configuration is complete, use a straight-through Ethernet patch cable to connect the router’s Ethernet WAN (ETH0) port to the Ethernet port of a WAN device (such as a modem). LEDs and What They Mean LEDs indicate the router’s operational status and port activity. AR450S System LEDs LED State Function Power Green The router is receiving power and the power
Inhaltszusammenfassung zur Seite Nr. 10
10 AR450S Router Troubleshooting Installation If you have problems installing the router, try one or more of the following: No LEDs Light The most likely reason is that the router is not receiving power. Check the following: 1. Check the supply outlet’s switch is in the ON position. 2. Test the mains power outlet to verify it is working. If the problem persists, contact your authorised Allied Telesyn distributor or reseller. LEDs Light Incorrectly If the System LED stays on, the router softwar
Inhaltszusammenfassung zur Seite Nr. 11
Quick Install Guide 11 ■ The AR400 Series Router Software Reference, which provides detailed information on configuring the router and its software. ■ AT-TFTP Server for Windows, for downloading software releases. ■ Adobe Acrobat Reader, for viewing online documentation. ■ Microsoft Internet Explorer. These documents can also be downloaded from the AR400 Series Router Support Site at www.alliedtelesyn.co.nz/support/ar400/. C613-04045-01 REV A
