Bedienungsanleitung BEA FALCON DR

Inhaltszusammenfassung zur Seite Nr. 1

FALCON DR / FALCON XL-DR

USER’S GUIDE

MOTION SENSORS FOR INDUSTRIAL DOORS

FALCON DR: double relay / high mount • FALCON XL-DR: double relay / low mount

Technology : Microwave and Hold time : 0.5s to 9s (adjustable)
TECHNICAL microprocessor Temperature range : -22°F to +122°F (-30°C to +60°C)
Transmitter frequency : 24.125 GHz Degree of protection : IP65
SPECIFICATION
Transmitter radiated power : <20 dBm EIRP Norm conformity : R&TTE 1999/5/EC
Transmitte

Inhaltszusammenfassung zur Seite Nr. 2

OPENING AND CLOSING THE SENSOR • Loosen the retaining nut until the cable slides easily into • Connect the quick disconnect terminal block to the main electronic the grommet ; circuit ; • Partially unscrew the 2 front cover screws ; • Slide the main electronic circuit into the 2 housing slot guides and • Pull out the front cover with the 2 front cover screws. pull the main cable gently at the same time ; • Gently push the front cover and make sure that the external housing is pr

Inhaltszusammenfassung zur Seite Nr. 3

SENSING FIELD DIMENSIONS FALCON (Mounting height: 16.5’ (5m) 6 3 0 3 6 6 3 0 3 6 The sensing fields here on The sensing fields the left correspond to the 3 3 here on the left 3 3 following adjustments: correspond to the 6 6 6 following adjustments: 6 • Tilt angle: 9 9 15°, 30°, 45° 9 9 • Tilt angle: 30° • Sensitivity: 9 • Sensitivity: 12 12 12 12 9,6,3

Inhaltszusammenfassung zur Seite Nr. 4

1. DESCRIPTION OF THE INFRARED REMOTE CONTROL CONFIGURATION WITH REMOTE CONTROL • Open the battery compartment at the back of the remote control ; • Insert two AAA batteries supplied with the remote control as shown beside ; • Close the battery compartment. (10) Not used 0-9 Number keys (1) (11) Not used (12) Not used (13) Not used Output redirection (2) (14) Not used Plus (3) (15) Check Values Unlock (4) (16) Lock Minus (5) Holdtime (6) (17) Output configu

Inhaltszusammenfassung zur Seite Nr. 5

Note: All parameters or functions listed in the following tables are only accessible if the sensor is in adjustment session. The red LED is then slowly flashing. During an adjustment session each parameter may be checked or changed at any time in the following way: PARAMETERS ACTIONS CHECK Press the key corresponding to the parameter to be checked and then press the CHECK VALUES key (15). VALUES Count the number of times the green LED flashes, which corresponds to the value of the

Inhaltszusammenfassung zur Seite Nr. 6

OUTPUT Key 2: towards or away mode detection Towards or away mode detection only works if the detection REDIRECTION Motion towards the detector triggers relay 1. parameter is set to 1 (bi-directional). Otherwise the sensor Motion away from the detector triggers relay 2. does not detect any motion anymore. This works also if pedestrian rejection is enabled (immunity parameter set to 3,4 or 5) OUTPUT Press the OUTPUT CONFIGURATION key (17). CONFIGURA- Use the NUMBER keys 1-4 (1) to se

Inhaltszusammenfassung zur Seite Nr. 7

SYMPTOM PROBABLE CAUSE CORRECTIVE ACTION TROUBLE- SHOOTING The door will not open and The sensor power is off. Check the wiring and the power supply. no red LED lights up. The door opens and closes The sensor "sees" the door moving. Increase the tilt angle and/or reduce the sensitivity. constantly. When closing the door creates vibrations Ensure that the sensor is correctly fixed. picked up by the sensor. If the rejection mode is set at level 1, set this parameter to level 2. Redu