Bedienungsanleitung InFocus DV 18V

Inhaltszusammenfassung zur Seite Nr. 1

Impact Drill
Model DV 18V
Handling instructions
Note:
Before using this Electric Power Tool, carefully read through these
HANDLING INSTRUCTIONS to ensure efficient, safe operation. It is
recommended that these INSTRUCTIONS be kept readily available
as an important reference when using this power tool.

Inhaltszusammenfassung zur Seite Nr. 2

17. Avoid unintentional starting. Do not carry a plugged- GENERAL OPERATIONAL PRECAUTIONS in tool with a finger on the switch. Ensure switch is off when plugging in. WARNING! When using electric tools, basic safety 18. Use outdoor extension leads. When tool is used precautions should always be followed to reduce the outdoors, use only extension cords intended for risk of fire, electric shock and personal injury, including outdoor use. the following. 19. Stay alert. Watch what you are doing. Use

Inhaltszusammenfassung zur Seite Nr. 3

SPECIFICATIONS Voltage (by areas)* (110V, 220V, 230V, 240V) Power input 690 W* Speed change 1 2 -1 -1 Forward rotation 0 – 1000 min 0 – 3000 min No load speed -1 -1 Reverse rotation 0 – 600 min 0 – 1800 min Steel 13 mm 8 mm Capacity Concrete 18 mm 13 mm Wood 40 mm 25 mm -1 -1 Full load impact rate 8400 min 27300 min Weight (without cord) 2.0 kg *Be sure to check the nameplate on product as it is subject to change by areas. 5. Mounting and dismounting of the bit. STANDARD ACCESSORIES For keyed ch

Inhaltszusammenfassung zur Seite Nr. 4

NOTE To attach a depth gauge on the side handle, insert When the sleeve does not become loose any further, the gauge into the U-shaped groove on the side fix the side handle to retaining ring, hold side handle handle, adjust the position of the depth gauge in firmly, then turn the sleeve to loosen by hand. (Fig. 4) accordance with the desired depth of the hole, and firmly tighten the side handle grip. (Fig. 7) Retaining ring Depth gauge Loosen Sleeve Side handle Side handle Loosen Tighten Fig. 4

Inhaltszusammenfassung zur Seite Nr. 5

9. High-speed/Low-speed changeover: 2. Drilling Prior to changing speed, ensure that the switch is in
When drilling, start the drill slowly, and gradually the OFF position, and the drill has come to a complete increasing speed as you drill. stop.
Always apply pressure in a straight line with the bit. To change speed, rotate the gear shift dial as indicated Use enough pressure to keep drilling, but do not by the arrow in Fig. 9. The numeral “1” engraved on push hard enough to stall the motor

Inhaltszusammenfassung zur Seite Nr. 6

MODIFICATION: Hitachi Power Tools are constantly being improved and modified to incorporate the latest technological advancements. Accordingly, some parts may be changed without prior notice. NOTE Due to HITACHI’s continuing program of research and development, the specifications herein are subject to change without prior notice. 6

Inhaltszusammenfassung zur Seite Nr. 7

7 1 2 3 3 Item Code No. Item Code No. 6 Remarks Remarks 4 No. No. Used No. No. Used 7 8 5 1 995-344 1 M6×25 40 322-862 1 9 2 987-576 1 41 322-853 1 10 11 31 321-814 1 13VLRB-D 42 322-854 1 12 32 322-357 1 13VLRH-N 43 321-630 1 100L 4 322-857 1 44 1 322-517 1 220V-240V 5 939-556 1 44 2 322-518 1 “GBR (110V)” 6 322-851 1 45 999-041 2 13 19 7 620-2DD 1 6202DDCMPS2L 46 955-203 2 22 14 ____ 21 8 322-850 1 47 1 30 13 20 31 9 984-101 1 48 994-273 1 10 959-150 1 D6.35 49 992-635 1 32 15 11 322-845 1 50

Inhaltszusammenfassung zur Seite Nr. 8

Hitachi Koki Co., Ltd. 404 Code No. C99131611 Printed in China