Bedienungsanleitung Chief Manufacturing KTP-Series

Inhaltszusammenfassung zur Seite Nr. 1

INSTALLATION INSTRUCTIONS
Horizontal And Vertical Table Stands
and Accessories
Model: KTP-Series
The KTP-Series is a free standing, pole mount solution for multiple displays.
KTP-320
KTP-220 / KTP-225
KTP-440 / KTP-445
KTP-230
BEFORE YOU BEGIN
CAUTION!
To prevent damage to the Kit, which could affect or void the Factory warranty, and to the equipment that will be
attached to it, thoroughly study all instructions and illustrations before you begin the installation.
 If you have any questions abo

Inhaltszusammenfassung zur Seite Nr. 2

Model: KTP-Series Installation Instructions TOOLS REQUIRED FOR INSTALLATION WEIGHT CAPACITIES  Phillips Head Screw Driver  3/4" Wrench KTP-220 / KTP-225: 35 lbs. per monitor  3/32" Hex Key (provided) KTP-230: 35 lbs. per moniter  5/32" Hex Key (provided) KTP-320: 30 lbs. per moniter  7/32" Hex Key (provided) KTP-440 / KTP-445: 20 lbs. per moniter PARTS Carefully inspect components for shipping damage . If damage is apparent, call your carrier claims agent and do not continue with installati

Inhaltszusammenfassung zur Seite Nr. 3

Installation Instructions Model: KTP-Series (160) (10 Includes 210, 220, 230) (180) (120) (200) (190) (20) (170) (130) (140) 250 260 (30) (110) (100) (40) 240 (80) (90) (50) (70) (60) Figure 1: Parts ASSEMBLY AND INSTALLATION (210) Mount Assembly (60) KTP-230 Assembly To assemble the KTP-230: (220) 1. Assemble pole (60) to base (40) using one 3/8-16 x 1" FHCS (90). (see Figure 2) (60) (230) (140) Figure 3: Mount Centris Head with Pole Clamp (90) (40) Figure 2: Assemble Pole to Base 2. Place f

Inhaltszusammenfassung zur Seite Nr. 4

Model: KTP-Series Installation Instructions NOTE: Equally tighten screws (230) against front pole Display Installation mount (210) and rear (220) pole clamps. Attach Centris Head to Flush Mount Display (see Figure 4) CAUTION! CAUTION: If display uses a screw size other than those included in the kit, DO NOT use the screws (230) provided. Using the wrong screws could result in damage to your monitor. Keep equal (220) distance between 1. Install two M4 x 12mm Phillips pan head screws (160) mount a

Inhaltszusammenfassung zur Seite Nr. 5

Installation Instructions Model: KTP-Series 3. Place display face down on a clean dry surface. Display 4. Place four 3/8" or 3/4" nylon spacers (190 or 200) Centris Head over four mounting holes in display back (see Figure 11). 5. Align Centris head mounting holes with four nylon spacers (see Figure 11). 6. Secure Centris head to display using four M4 x 20mm Phillips pan head screws (170), or four M4 x 30mm Phillips pan head screws (180) (see Figure 11). (20, 30) Phillips Pan Head Screw (160) (1

Inhaltszusammenfassung zur Seite Nr. 6

Model: KTP-Series Installation Instructions Display Pitch and Roll Adjustment To adjust display pitch or roll position: (20, 30) 1. Loosen Centris bracket front adjustment knob. (see Figure 15) End Lock 2. Tilt display up or down, or adjust display roll left or right until properly positioned. 3. Tighten Centris bracket front adjustmnent knob. Pitch/Roll Centris Head End Lock Retaining Screw Adjustment Knob Figure 13: Reinstall End Lock(s) ADJUSTMENTS Display Adjustment The KTP Series mount all

Inhaltszusammenfassung zur Seite Nr. 7

Installation Instructions Model: KTP-Series 7

Inhaltszusammenfassung zur Seite Nr. 8

Model: KTP-Series Installation Instructions 8