Inhaltszusammenfassung zur Seite Nr. 1
INSTALLATION INSTRUCTIONS
Large Flat Panel Dual Arm Wall Mount
Model PNR™
The PNR is wall-mounted, rugged, versatile, and
installer-friendly. The PNR is compatible with the
standard (14” x 14”) PSB interface bracket in which a
display can be mounted in either the landscape or
portrait position on the PNR.
The dual arms on the PNR:
Extend from the wall 25” in length
Pivot up to 90º left or right of center
The standard PNR is shipped with the support posts for
the dual arms centered in the mount.
Inhaltszusammenfassung zur Seite Nr. 2
Model PNR™ Installation Instructions IMPORTANT WARNINGS AND CAUTIONS! WARNING: A WARNING alerts you to the possibility of serious injury or death if you do not follow the instructions. CAUTION: A CAUTION alerts you to the possibility of damage or destruction of equipment if you do not follow the corresponding instructions. WARNING: Improper installation can result in serious personal injury! Make sure that the structural members can support a redundant weight factor five times the total weight
Inhaltszusammenfassung zur Seite Nr. 3
Installation Instructions Model PNR™ DIMENSIONAL DRAWING 3
Inhaltszusammenfassung zur Seite Nr. 4
Model PNR™ Installation Instructions Inspect The Unit Before Installing PARTS LIST WARNING: Watch for pinch points. Do not put your Unpack the carton and verify the contents listed in Table fingers between movable parts. 3. If you are missing any of the listed parts, contact Customer Service at: 1-800-582-6480. 1. Carefully inspect the PNR for shipping damage. If any damage is apparent, call your carrier claims agent and do not continue with the installation until the Table 3: Parts List carrie
Inhaltszusammenfassung zur Seite Nr. 5
Installation Instructions Model PNR™ NOTE: Do not tighten the lag bolts down at this time. INSTALLATION Leave enough space between the wall and lag WARNING: Improper installation can result in serious bolts to hang the PNR. personal injury! 16" WARNING: It is the responsibility of the installer to verify that the wall to which the PNR is anchored will safely support five times the combined load of all Wood Studs attached components and equipment. If not, reinforce the structure before installing
Inhaltszusammenfassung zur Seite Nr. 6
Model PNR™ Installation Instructions Install Cover Plates and End Caps Mount (Hang) the PNR on Lag Bolts NOTE: The cover plates and end caps have pressure fitting ends that lock in place with each other. 1. Install cover plate (20) over the top bracket. (See figure 5) 2. Install end cap (30) on the cover plate (20). (See figure 5) 3. Repeat steps 1 and 2 for the bottom mounting bracket. (See figure 5) Figure 2 Adjustment Nut Figure 4 End Caps (30) Use Lag Bolts and Washers to Fasten PNR to the
Inhaltszusammenfassung zur Seite Nr. 7
Installation Instructions Model PNR™ Mount the Display 1. Make sure power is not supplied (turned off) to the display before attempting to mount the display. 2. Following the instructions for mounting the PSB Remove pin interface bracket of your specific plasma display 4 and nut and panel, install the mounting bracket on your plasma move to lower holes display panel. WARNING: Watch for pinch points. Do not put your fingers between movable parts. 5 3. While supporting both sides of display, align
Inhaltszusammenfassung zur Seite Nr. 8
Model PNR™ Installation Instructions TM Centris Select Management Channel Adjustment Knob Figure 10 Figure 8 3. To lock the mount at the desired vertical tilt, tighten the vertical tilt lock screw. (See figure 11) Bottom Cable Management Channel Vertical Tilt Lock Screw Figure 11 Figure 9 Lateral Tilt Tension Adjustment CAUTION: Overtightening lateral adjustment will ADJUSTMENTS cause excessive wear and may distort adjustment components. TENSION ADJUSTMENTS 1. Using a 9/16” wrench (not provide
Inhaltszusammenfassung zur Seite Nr. 9
Installation Instructions Model PNR™ reconfiguring the mount. Use the first and third slotted holes in the top and bottom mounting brackets. Reconfiguring the Swing Arms Right of Center With some disassembly and reassembly, you can move the swing arms to the right of center by reconfiguring the Lateral Tilt mount. Use the third and fifth slotted holes in the top and Adjustment Nut bottom mounting brackets. Adjusting the Swing Arms Off Center To adjust the dual swing arm mount configuration: 1.
Inhaltszusammenfassung zur Seite Nr. 10
Model PNR™ Installation Instructions bottom) and secure using two bolts (one top and one NOTE: The display may need to be repositioned in order bottom). to gain access to the tension adjustment screw(s). 5. Install four bolts (two on the top and two on the bottom) to secure the swing arm assembly to the top 3. Using the wrench provided with the mount, turn and bottom mounting brackets (See figure 14). adjustment bar clockwise to increase swing arm tension or counterclockwise to reduce swing arm
Inhaltszusammenfassung zur Seite Nr. 11
Installation Instructions Model PNR™ Remove bolt 1 or padlock Increase 2 if used Pin in "Closed" position - move to "Open" position to remove display Figure 18 Removing Display from Mount 1. Remove bolt or padlock from faceplate (if used). 4 NOTE: The pin may have been used as a more permanent locking device. If so, remove nut and pin and move from the lower holes to the upper holes. 2. Pull back on flag on upper mounting hole and press pin down into "Open" position. (See Figure 19) WARNING: DIS
Inhaltszusammenfassung zur Seite Nr. 12
Model PNR™ Installation Instructions 12
