Bedienungsanleitung Chief Manufacturing Universal Slat Wall Multi Arm Mount KSY220

Inhaltszusammenfassung zur Seite Nr. 1

INSTALLATION INSTRUCTIONS
Universal Slat Wall
Multi Arm Mount
KSY220

Inhaltszusammenfassung zur Seite Nr. 2

KSY220 Installation Instructions DISCLAIMER WARNING: Failure to read, thoroughly understand, and CSAV, Inc., and its affiliated corporations and subsidiaries follow all instructions can result in serious personal injury, (collectively, "CSAV"), intend to make this manual accurate and damage to equipment, or voiding of factory warranty! It is the complete. However, CSAV makes no claim that the information installer’s responsibility to make sure all components are contained herein covers all deta

Inhaltszusammenfassung zur Seite Nr. 3

Installation Instructions KSY220 LEGEND Pencil Mark Tighten Fastener Marcar con lápiz Apretar elemento de fijación Stiftmarkierung Befestigungsteil festziehen Marcar com lápis Apertar fixador Segno a matita Serrare il fissaggio Potloodmerkteken Bevestiging vastdraaien Marquage au crayon Serrez les fixations Drill Hole Loosen Fastener Perforar Aflojar elemento de fijación Bohrloch Befestigungsteil lösen Fazer furo Desapertar fixador Praticare un foro Allentare il fissaggio Gat boren Bevestiging l

Inhaltszusammenfassung zur Seite Nr. 4

KSY220 Installation Instructions TOOLS REQUIRED FOR INSTALLATION 1/8" 3/16" 5/32" (Provided) (Provided) (Provided) PARTS B (1) C (1) A (1) E (1) D (1) F (1) G (4) H (2) 1/8" 5/32" 3/16" #8-32 X 3/8" J J ( (2) 2) M (2) P (2) K (4) N (2) L (2) UHMW 5/16-18 .320 x .563 x .018" Q (2) Q2 (4) Q3 (4) Q4 (4) Q5 (4) Q1 (4) .500 x .194 x .750 M4 x 30mm .500 x .194 x .375 M4 X 12mm M4 x 20mm 4

Inhaltszusammenfassung zur Seite Nr. 5

Installation Instructions KSY220 INSTALLATION (C) X 1 WARNING: FAILURE TO PROVIDE ADEQUATE STRUCTURAL STRENGTH FOR THIS COMPONENT CAN RESULT IN SERIOUS PERSONAL INJURY OR DAMAGE TO EQUIPMENT! It is the installer’s responsibility to make sure the structure to which this component is attached can support five times the combined weight of all equipment. Reinforce the structure as required before installing the component. OFBU and Wall Plate Installation 1. Install OFBU (C) following the instructio

Inhaltszusammenfassung zur Seite Nr. 6

KSY220 Installation Instructions (J) X 2 (M) X 2 4 (K) X 4 1 (L) X 2 (A) X 2 3 (N) X 2 2 (P) X 2 Figure 4 in the previous step) with the two top teardrop mounting Display Installation holes on the Centris cup. The mounting holes on the back of the display will be flush with the back surface, or recessed into the back. Refer to the applicable installation procedure below. CAUTION: IMPROPER INSTALLATION CAN LEAD TO Flush Mount Display Installation DISPLAY FALLING CAUSING SERIOUS PERSONAL INJURY O

Inhaltszusammenfassung zur Seite Nr. 7

Installation Instructions KSY220 Centris Cup Centris Cup (Q4 or Q5) 7 (4 places) 4 (Q3) x 2 (Q1 or Q2) 5 (4 places) Figure 6 6. Repeat display installation procedures for second display. 7. Proceed to "CABLE MANAGEMENT." Recessed Mount Display Installation Figure 7 1. Ensure Centris bracket is able to swivel and tilt easily, yet Cable Management still be tight enough to hold display in desired position. Adjust as required before proceeding. See 1. Attach all cables to display. "ADJUSTMENT" for

Inhaltszusammenfassung zur Seite Nr. 8

KSY220 Installation Instructions 2. Using Phillips screwdriver, slightly loosen or tighten the adjustment screw as necessary (See Figure 11). Adjustment Screw 2 Cable Management Bracket (in open position) Cable Path (typical) Figure 11 NOTE: Display not shown for clarity. 3. Reinstall display. See Display Installation in this Figure 9 document. 4. Close cable management bracket by sliding it back towards Swing Arm Tension Adjustment the centerline of the arm (See Figure 8). 1. Using 3/16" hex wr

Inhaltszusammenfassung zur Seite Nr. 9

Installation Instructions KSY220 9

Inhaltszusammenfassung zur Seite Nr. 10

KSY220 Installation Instructions USA/International A 8401 Eagle Creek Parkway, Savage, MN 55378 P 800.582.6480 / 952.894.6280 F 877.894.6918 / 952.894.6918 Europe A Fellenoord 130 5611 ZB EINDHOVEN, The Netherlands P +31 (0)40 2668620 F +31 (0)40 2668615 Asia Pacific A Room 30I, Block D, Lily YinDu International Building LuoGang, BuJi Town, Shenzhen, CHINA. Post Code: 518112 8832-000239 RevA 2007 Chief Manufacturing www.chiefmfg.com P +86-755-8996 9226 ; 8996 9236 ; 8996 9220 12/07 F +86-755-89