Bedienungsanleitung IBM ThinkPad i 143K

Bedienungsanleitung für das Gerät IBM ThinkPad i 143K

Gerät: IBM ThinkPad i 143K
Kategorie: Laptop
Produzent: IBM
Größe: 2.23 MB
Datum des Hinzufügens: 8/10/2014
Seitenanzahl: 91
Anleitung drucken

Herunterladen

Wie kann man es nutzen?

Unser Ziel ist Ihnen einen schnellen Zugang zu Inhalten in Bedienungsanleitungen zum Gerät IBM ThinkPad i 143K zu garantieren. Wenn Sie eine Online-Ansicht nutzten, können Sie den Inhaltsverzeichnis schnell durchschauen und direkt zu der Seite gelangen, auf der Sie die Lösung zu Ihrem Problem mit IBM ThinkPad i 143K finden.

Für Ihre Bequemlichkeit

Wenn das direkte Durchschauen der Anleitung IBM ThinkPad i 143K auf unserer Seite für Sie unbequem ist, können sie die folgende zwei Möglichkeiten nutzen:

  • Vollbildsuche – Um bequem die Anleitung durchzusuchen (ohne sie auf den Computer herunterzuladen) können Sie den Vollbildsuchmodus nutzen. Um das Durchschauen der Anleitung IBM ThinkPad i 143K im Vollbildmodus zu starten, nutzen Sie die Schaltfläche Vollbild
  • Auf Computer herunterladen – Sie können die Anleitung IBM ThinkPad i 143K auch auf Ihren Computer herunterladen und sie in Ihren Sammlungen aufbewahren. Wenn Sie jedoch keinen Platz auf Ihrem Gerät verschwenden möchten, können Sie sie immer auf ManualsBase herunterladen.
IBM ThinkPad i 143K Handbuch - Online PDF
Advertisement
« Page 1 of 91 »
Advertisement
Druckversion

Viele Personen lesen lieber Dokumente nicht am Bildschirm, sondern in gedruckter Version. Eine Druckoption der Anleitung wurde ebenfalls durchdacht, und Sie können Sie nutzen, indem Sie den Link klicken, der sich oben befindet - Anleitung drucken. Sie müssen nicht die ganze IBM ThinkPad i 143K Anleitung drucken, sondern nur die Seiten, die Sie brauchen. Schätzen Sie das Papier.

Zusammenfassungen

Unten finden Sie Trailer des Inhalts, der sich auf den nächsten Anleitungsseiten zu IBM ThinkPad i 143K befindet. Wenn Sie den Seiteninhalt der nächsten Seiten schnell durchschauen möchten, können Sie sie nutzen.

Inhaltszusammenfassungen
Inhaltszusammenfassung zur Seite Nr. 1


S37L-5192-00
IBM Mobile Systems
ThinkPad i Series 1400 (2611)

This Manual Supports The
Following Models:

1412, 1419, 1452, 1456,
1459, 1472, 1476, 1479,
140A, 140C, 140F, 140H, 140K,
140L, 140M, 140T, 143C, 143H,
143K, 143L, 143M, 143T, 147A,
147F, 147A, 149C, 149F, 149H,
149K, 149M, 149T,

Hardware Maintenance Manual

May 1998

Inhaltszusammenfassung zur Seite Nr. 2

Before using this information and the product it supports, be sure to read the general information under “Read This First” on page 1. First Edition (May 1999) The following paragraph does not apply to the United Kingdom or any country where such provisions are inconsistent with local law: INTERNATIONAL BUSINESS MACHINES CORPO- RATION PROVIDES THIS PUBLICATION "AS IS" WITHOUT ANY WARRANTY OF ANY KIND, EITHER EXPRESS OR IMPLIED, INCLUDING, BUT NOT LIMITED TO, THE LIMITED WARRANTIES OF MERCHANTAB

Inhaltszusammenfassung zur Seite Nr. 3

Contents ThinkPad i Series 1400 Hardware Maintenance Manual . . . . . . . . . . . . . . . . . . . . . 1 Read This First .................. 1 How to Use Error Messages .......... 1 How to Diagnose Multiple FRUs ........ 1 What to Do First ................ 2 Screw Notices . . . . . . . . . . . . . . . . . 3 Power-On and Setup Password .......... 4 Check Procedures . . . . . . . . . . . . . . . . 5 Power Systems Check ............. 6 Planar Board Check .............. 8 Memory Check . . . . . .

Inhaltszusammenfassung zur Seite Nr. 4

Battery Assembly . . . . . . . . . . . . . . . 36 DIMM and DIMM Cover ............ 37 Modem Board Cover and Modem Board .... 38 Keyboard . . . . . . . . . . . . . . . . . . . 39 CPU Thermal Plate .............. 41 RTC Battery, CPU EMI Shield and Hard Disk Drive 42 PCMCIA Holder . . . . . . . . . . . . . . . . 44 LCD Assembly ................. 45 Upper Cover (Keyboard Bezel) ......... 47 CD Control Card ................ 49 Trajection Board and Modem Connector (RJ11 Cable Assembly) . . . . . . .

Inhaltszusammenfassung zur Seite Nr. 5

ThinkPad i Series 1400 Hardware Maintenance Manual Read This First Before you go to the check procedures, be sure to read this section. Important Notes Ÿ Only certified trained personnel should service the computer. Ÿ Read the FRU service procedures before replacing any FRUs. Ÿ Be extremely careful during write operations such as copying, saving, or formatting. Drives in the computer that you are servicing might have been rearranged or the drive startup sequence might have been altered. If you s

Inhaltszusammenfassung zur Seite Nr. 6

What to Do First The servicer must include the following in the parts exchange form or parts return form that is attached to the returned FRU: 1. Name and phone number of servicer. 2. Date of service. 3. Date when part failed. 4. Date of purchase. 5. Failure symptoms, error codes appearing on display, and beep symptoms. 6. Procedure index and page number in which failing FRU was detected. 7. Failing FRU name and part number. 8. Machine type, model number and serial number. 9. Customer's name and

Inhaltszusammenfassung zur Seite Nr. 7

If the following symptoms are present, they may indicate damage caused by non-warranted activity: Ÿ Missing parts may be a symptom of unauthorized service or modification. Ÿ HDD spindles can become noisy if subjected to excessive force or by being dropped. Screw Notices The computer uses special nylon-coated screws with the following characteristics: Ÿ They maintain tight connections. Ÿ They do not easily come loose, even with shock or vibration. Ÿ They need additional force to tighten. Ÿ They

Inhaltszusammenfassung zur Seite Nr. 8

Power-On and Setup Password To clear a password from the system, first identify the system password switch by referring to “Switch Locations” on page 74, then follow these steps: 1. Turn off the computer. 2. Unplug the AC Adapter and remove the battery. 3. Remove the keyboard by referring to “Keyboard” on page 39, and the thermal plate by referring to “CPU Thermal Plate” on page 41. 4. Move the password switch (SW3, switch 4) from OFF to ON to bypass the password. Note: SW2 has four switches. It

Inhaltszusammenfassung zur Seite Nr. 9

Check Procedures Use the following procedure as a guide for computer prob- lems. Notes: 1. The diagnostic tests are intended to test only IBM products. Non-IBM products, prototype cards, or mod- ified options can give false errors and invalid system responses. 2. Some test items require tools as shown below: Ÿ Audio wrap cable (P/N: 65G5180) Ÿ FDD: Erasable 2HD diskette Ÿ Parallel: Wrap plug (P/N: 72X8546) Ÿ Parallel: Test cable (P/N: 05K2580) Ÿ Serial: Wrap plug (P/N: 72X8546) Ÿ PCMCIA: PC te

Inhaltszusammenfassung zur Seite Nr. 10

Symptoms (Verified) Go to Other symptoms Appropriate check instructions in this section, then use appropriate tables in “Symptom-to-FRU Index” on page 17. Power Systems Check To verify the symptom of the problem, power on the com- puter using each of the power sources as follows: 1. Remove the battery pack, diskette drive, and hard disk drive. 2. Connect the AC Adapter and check that power is sup- plied. 3. Install the diskette drive or hard disk drive one at a time, and check that power is supp

Inhaltszusammenfassung zur Seite Nr. 11

Ÿ If the measured voltage is correct, replace the planar board. Ÿ If the problems still persist, go to “Undetermined Problems” on page 25. Ÿ If the voltage is not correct, go to the next step. 2. Unplug the AC Adapter cable from the AC power outlet and wait for five minutes or longer to allow the over-voltage protection circuit of the AC Adapter to be fully discharged and initialized. 3. Plug the AC Adapter cable into the AC power outlet. 4. Measure the output voltage of the AC Adapter. 5. If th

Inhaltszusammenfassung zur Seite Nr. 12

Terminal Signal / Voltage (V dc) 4 Reserved 5 Thermal 6 Sense 7 Ground Note: Signal lines, not used in these steps, are used for communication between the system and the battery. 3. If the voltage is less than +8 V dc, recharge the battery pack. If the voltage is still less than +8 V dc after recharging, replace the battery. Planar Board Check The planar board performs processing functions. Thus, the planar board can cause processor problems. To verify the problem, do the following: 1. Boot from

Inhaltszusammenfassung zur Seite Nr. 13

DIMM DIMM Total Memory 128MB 64MB 192MB 64MB 128MB 192MB 128MB 128MB 256MB CAUTION: This system cannot work without DIMM memory. Memory errors might stop system operation, show error messages on the screen, or hang the system. Use the following procedure to isolate memory problems: Note: Make sure that the DIMM is properly installed into the connector. A loose connection can cause an error. 1. Power off the computer and replace the DIMM. 2. Boot from the diagnostics diskette and start the PC Doc

Inhaltszusammenfassung zur Seite Nr. 14

Ÿ Replace the planar board. The following external input devices are supported for this computer: Ÿ Numeric keypad Ÿ Mouse (PS/2 compatible) Ÿ Keyboard If any of these devices do not work, reconnect the cable connector and repeat the failing operation. If the problem still exists, replace the device, and then the planar board. Audio Function Check Do as follows: 1. Boot from the diagnostics diskette and start the PC Doctor program (please refer to “Running the PC Doctor Diagnostics Program” on

Inhaltszusammenfassung zur Seite Nr. 15

If either the pointing stick or the click button does not work, do the following actions one a time to correct the problem. Do not replace a non-defective FRU. 1. Reconnect the keyboard flexible cables and the TrackPoint flexible cable. 2. Replace the TrackPoint board. 3. Replace the keyboard. 4. Replace the planar board. Diskette Drive Check Do the following to isolate the problem to a controller, drive, or diskette. A scratch, write-enabled, non-defective, high-density (2HD) diskette is requir

Inhaltszusammenfassung zur Seite Nr. 16

If an error occurs, reconnect the connector on the planar board. If the error still remains: 1. Reconnect the CD-ROM/DVD-ROM drive cable. 2. Replace the CD-ROM/DVD-ROM drive cable. 3. Replace the CD-ROM/DVD-ROM drive. 4. Replace the planar board. Modem Board Check Do the following to isolate the problem to the system internal modem: 1. Boot from the diagnostics diskette and start the PC Doctor program (please refer to “Running the PC Doctor Diagnostics Program” on page 29). 2. Select Diagnostic

Inhaltszusammenfassung zur Seite Nr. 17

BIOS Utility Your computer has a BIOS Utility that allows you to con- figure the computer an its hardware settings. Note: The computer is also bundled with a Windows- based computer management utility similar in func- tion with the BIOS Utility called the Notebook manager. The computer is already correctly configured for you. If you make any changes to the computer or you receive an Equipment Configuration Error message (error code 246) after you turn on the computer, you need to run the BIOS

Inhaltszusammenfassung zur Seite Nr. 18

Navigating the BIOS Utility Keep in mind the following when using the BIOS Utility: Ÿ From the main menu screen, press the up or down arrow keys to move from one menu item to another; then press Enter to enter the selected menu. Ÿ Parameters displayed in low brightness (grayed out) are not user-configurable. The computer detects and sets the values for these parameters. Ÿ Press the up or down arrow keys to move from one parameter to another. Press the left or right arrow keys to change parameter

Inhaltszusammenfassung zur Seite Nr. 19

Power Management Features Two power management modes are available in the com- puter system to reduce power consumption and to prolong battery life. Screen Blanking Mode When in screen blanking mode, the following occurs: Ÿ The LCD backlight turns off. Events that cause the computer to enter screen blanking mode: Ÿ Screen blanking requested by the Fn key (Fn+F3). Standby Mode When in standby mode, the following occurs: Ÿ The LCD backlight turns off. Ÿ The hard disk motor stops. Ÿ CPU stops the

Inhaltszusammenfassung zur Seite Nr. 20

Note: If the computer enters standby mode and the com- puter is using a communication or I/O PC Card, the PC Card and application program remain active. Hibernation Mode When in hibernation mode, the following occurs: Ÿ The system status, RAM, VRAM, and setup data are stored on the hard disk. Ÿ The system is powered off. Events that cause the computer to enter hibernation mode: Ÿ Function combination key (Fn+F12) is pressed. Ÿ The battery power is at a critically-low level. Note: Before enterin


Ähnliche Anleitungen
# Bedienungsanleitung Kategorie Herunterladen
1 IBM 1300 Handbuch Laptop 23
2 IBM 39T9401 Handbuch Laptop 7
3 IBM 770 Handbuch Laptop 41
4 IBM 4400 Handbuch Laptop 4
5 IBM 560E Handbuch Laptop 17
6 IBM 390E Handbuch Laptop 52
7 IBM 8413 Handbuch Laptop 3
8 IBM 92P1703 Handbuch Laptop 1
9 IBM 39T9414 Handbuch Laptop 1
10 IBM 4693 DBCS FAMILY Handbuch Laptop 0
11 IBM A Series Handbuch Laptop 12
12 IBM 4694 DBCS FAMILY Handbuch Laptop 6
13 IBM AC453A Handbuch Laptop 0
14 IBM 8414 Handbuch Laptop 3
15 IBM Dock I Handbuch Laptop 1
16 Sony CG-FX120K Handbuch Laptop 13
17 Sony FX120K Handbuch Laptop 8
18 Sony DG1 Handbuch Laptop 4
19 Sony BX540-BTO Handbuch Laptop 2
20 Sony FX150K Handbuch Laptop 2