Inhaltszusammenfassung zur Seite Nr. 1
GFU19 Multi-Tech CDMA Quick Guide
July, 2005
GFU19 Multi-Tech CDMA Modem
This guide describes how to configure your GPS1200
sensor and Multi-Tech CDMA for connection to a network
using a Verizon Wireless Internet data plan.
Topics • (Over the air) OTA Activation Using Your Internet Data Plan
• Setting Up the Multi-Tech CDMA Modem
• Connecting to a Network Using the Multi-Tech CDMA Modem
Inhaltszusammenfassung zur Seite Nr. 2
GFU19 Multi-Tech CDMA Modem Table of Contents Introduction..........................................................................................................................3 OTA Activation Using Your Internet Data Plan ...................................................................4 Setting Up the Multi-Tech CDMA Modem ...........................................................................8 Connecting to a Network Using the Multi-Tech CDMA Modem .........................
Inhaltszusammenfassung zur Seite Nr. 3
GFU19 Multi-Tech CDMA Modem Introduction This Quick Guide is designed to provide a step by step guide to configuring the About this GPS1200 sensor and Multi-Tech CDMA for connection to a network using a Verizon Quick Guide Wireless Internet data plan. This Quick Guide assumes that the user is familiar with general GPS surveying procedures and real time applications. Note: Please setup an Internet Data plan from Verizon Wireless and have it activated before using this manu
Inhaltszusammenfassung zur Seite Nr. 4
GFU19 Multi-Tech CDMA Modem OTA Activation Using Your Internet Data Plan Activate your Follow the steps below to configure and activate your Verizon Wireless Internet plan for use with the GPS1200 sensor and the Multi-Tech CDMA modem. Internet plan Step Action Display 1 Begin with the sensor turned off. • Attach your CDMA module to Port 1 or 3 on the sensor. • Press the ON (PROG) button to turn on the sensor. • Select 5 Config… from the Main Menu. This
Inhaltszusammenfassung zur Seite Nr. 5
GFU19 Multi-Tech CDMA Modem OTA Activation Using Your Internet Data Plan Step Action Display 4 From the CONFIGURE Real-Time Mode screen: • Ensure that the R-Time Mode and R- Time Data fields are set appropriately. • Select the port to which your modem is attached in the Port field. • Press the F5 (DEVCE) button. This takes you to the CONFIGURE Devices screen. 5 From the CONFIGURE Devices screen: • Press the F6 (PAGE) button once to access the “Modems
Inhaltszusammenfassung zur Seite Nr. 6
GFU19 Multi-Tech CDMA Modem OTA Activation Using Your Internet Data Plan Step Action Display 6 From the CONFIGURE Interfaces screen: • Highlight Real-Time and press the F4 (CTRL) button. This takes you to the CONFIGURE GPRS/Internet Connection screen. 7 In the CONFIGURE GPRS/Internet Connection screen: • Press the SHIFT button and the following screen appears. • Press the F3 (REG) button This takes you to the CONFIGURE CDMA Registration screen.
Inhaltszusammenfassung zur Seite Nr. 7
GFU19 Multi-Tech CDMA Modem OTA Activation Using Your Internet Data Plan Step Action Display 9 During the modem activation process: • Press the F4 (OK) button when the Information box shown on the right appears. The activation might take up to a few minutes. The modem will be ready for use a few minutes after activation. 10 If the modem activation process fails: • Re-enter your phone number and Retry. Note: If modem activation still fails, refer to
Inhaltszusammenfassung zur Seite Nr. 8
GFU19 Multi-Tech CDMA Modem Setting Up the Multi-Tech CDMA Modem Follow the steps below to setup the GPS1200 sensor to use the GFU19 Multi-Tech Set up the CDMA modem. Multi-Tech CDMA Modem Step Action Display 1 Begin with the sensor turned off. • Attach your CDMA module to Port 1 or 3 on the sensor. • Press the ON (PROG) button to turn on the sensor. • Select 5 Config… from the Main Menu. This takes you to the GPS1200 Configuration screen. 2 From
Inhaltszusammenfassung zur Seite Nr. 9
GFU19 Multi-Tech CDMA Modem Setting Up the Multi-Tech CDMA Modem Step Action Display 4 From the CONFIGURE Internet Interface screen: • Set Internet to Yes. • Set the Port to 1 or 3 as applicable. • Set the IP Address to Dynamic or Static, depending on your plan. Note: If you are using a Static IP Address, be sure to obtain it from Verizon Wireless and enter it in the Set IP Adr field. • Press the F5 (DEVCE) button. This takes you to the CONFIGURE GPRS In
Inhaltszusammenfassung zur Seite Nr. 10
GFU19 Multi-Tech CDMA Modem Setting Up the Multi-Tech CDMA Modem Step Action Display 6 From the CONFIGURE Edit Device: MultiTech CDMA screen: • Ensure the settings are as shown: GPRS/Internet: Yes Baud Rate: 115200 Parity: None Data Bits: 8 Stop Bit: 1 Flow Control: RTS/CTS • Press the F4 (ATCMD) button. This takes you to the CON
Inhaltszusammenfassung zur Seite Nr. 11
GFU19 Multi-Tech CDMA Modem Setting Up the Multi-Tech CDMA Modem Step Action Display 8 In the CONFIGURE Edit Device: MultiTech CDMA screen: • Press the F1 (STORE) button to save the changes. This returns you to the CONFIGURE GPRS Internet Devices screen. • Highlight MultiTech CDMA and press the F1 (CONT) button. This returns you to the CONFIGURE Internet Interfaces screen. 9 In the CONFIGURE Internet Interfaces screen: • Press the F1 (CONT) bu
Inhaltszusammenfassung zur Seite Nr. 12
GFU19 Multi-Tech CDMA Modem Connecting to a Network Using the Multi-Tech CDMA Modem Follow the steps below to connect the GPS1200 sensor to a network using the Multi- Connect with Tech CDMA modem. the Multi-Tech CDMA modem Step Action Display 1 Continuing from the previous section: • In the Main Menu select 5 Config… • In the Configuration Menu select 4 Interfaces… • In the Interfaces Menu highlight Real- Time and press the F3 (EDIT) button. This takes
Inhaltszusammenfassung zur Seite Nr. 13
GFU19 Multi-Tech CDMA Modem Connecting to a Network Using the Multi-Tech CDMA Modem Step Action Display 3 In the Interfaces screen: • Press the F4 (CTRL) button to set up your IP information. This takes you to the Set NET Port screen. 4 In the Set NET Port screen: • In the User field, select Client. • Enter the IP address and Port number of the station you are connecting to in the IP Address and TCP/IP Port fields, respectively. Note: Leave the A
Inhaltszusammenfassung zur Seite Nr. 14
GFU19 Multi-Tech CDMA Modem Connecting to a Network Using the Multi-Tech CDMA Modem Step Action Display 6 In the Survey Begin screen: • Review the job information and make any changes needed. • Press the F1 (CONT) button to begin the survey. This takes you to the Survey: Default screen. 7 In the Survey: Default screen: • Press the SHIFT -F3 (CONEC) button to establish a connection with the reference station. 8 This will establish a con
Inhaltszusammenfassung zur Seite Nr. 15
GFU19 Multi-Tech CDMA Modem Connecting to a Network Using the Multi-Tech CDMA Modem Step Action Display 9 This disables the connection with the reference station. You should see the NET1: Disconnected message at the bottom of the screen This concludes the Connecting to a Network Using the Multi-Tech CDMA section. GPS1200 GFU19 MultiTech CDMA Modem Quick Guide July, 2005 Page 15/18
Inhaltszusammenfassung zur Seite Nr. 16
GFU19 Multi-Tech CDMA Modem Appendix 1: Alternative Method of Activation Please verify all of your account information with Verizon Alternative Wireless. method Ask for both your MIN and MDM number, it is possible that they are different. MDM Number - Verizon phone number MIN - Mobile Identification Number Note: If your MIN and MDM number are different please note the numbers and follow the alternative procedure below. Step Action Display 1 This step continues
Inhaltszusammenfassung zur Seite Nr. 17
GFU19 Multi-Tech CDMA Modem Appendix 1: Alternative Method of Activation Step Action Display 2 From the CONFIGURE Send Command to Device screen: Activate you MDM number: • Enter the following commands exactly as shown and press the F3 (SEND) button after each one has been entered. The response should be OK for each entry. • AT+WSPC=1,000000 (INCLUDE COMMA!) • AT+WMDN=n Where n is your 10- digit Verizon phone number. This number may extend into the (cont) f
Inhaltszusammenfassung zur Seite Nr. 18
GFU19 Multi-Tech CDMA Modem Appendix 1: Alternative Method of Activation Step Action Display 3 During activation you may see the following messages displayed at the bottom of the screen: +WOTS: “SPL unlocked” +WOTP: “PRL download OK” +WOTM: “MDM download OK” +WOT2: “Programming Successful” Your Modem is now ready for use! GPS1200 GFU19 MultiTech CDMA Modem Quick Guide July, 2005 Page 18/18
