Inhaltszusammenfassung zur Seite Nr. 1
Owner’s Manual
Network Set-up and Operation
Wired Setting
Projector Set-up and Operation
This is the manual for the Network function.
Read this manual thoroughly to operate the Network function.
First, read the owner's manual of the projector to understand the basic
operation of the projector and the safety instructions.
The safety instructions in the owner's manuals should be followed strictly.
Inhaltszusammenfassung zur Seite Nr. 2
Compliance Federal Communications Commission Notice This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to Part 15 of FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful i
Inhaltszusammenfassung zur Seite Nr. 3
Safety instructions CAUTION IN USING THE PROJECTOR VIA NETWORKS ●W hen you find a problem with the projector, remove the power cable immediately and inspect the unit. Using the projector with failure may cause fire or other accidents. ● If you remotely use the projector via networks, carry out a safety check regularly and take particular care to its environment. Incorrect installation may cause fire orother accidents. CAUTION IN USING N
Inhaltszusammenfassung zur Seite Nr. 4
Table of contents Compliance ....................................................................................................................................................................................2 Safety instructions .....................................................................................................................................................................3 Table of contents ....................................................................................
Inhaltszusammenfassung zur Seite Nr. 5
Chapter 1 1 Preparation Describes features and operating environment of this projector. ENGLISH ENGLISH
Inhaltszusammenfassung zur Seite Nr. 6
Chapter 1 Preparation Features Web Management function ( +p.31) With this function, you can monitor projector functions such as power status, lamp status, input mode, signal condition, lamp-use time, etc. through the network by using the web browser installed on your computer. PC1 PC2 Turn on PJ1 PJ2 PJ1 Internet PC3 PC4 Intranet PC5 E-Mail Alert function ( +p.25) The projector sends messages to the registered e-mail addresses when a lamp abnormal- ity or power failure occurs with the projecto
Inhaltszusammenfassung zur Seite Nr. 7
Computerenvironment Features Required operating environment for computers When operating the projector via networks, computers should meet the operating envi- ronment below. Windows 2000, Windows XP (32bit version), Windows Vista (32bit version), Windows 7 (32bit version) Operating System Mac OS X v 10.4 or 10.5 Windows: Pentium III 900MHz or more RecommendedCPU Macintosh : 8 00 MHz PowerPC G4 or faster,or 1.8 GHz Intel Core Processor or faster Windows : 64MB (Minimum)/ 128MB or more (Re
Inhaltszusammenfassung zur Seite Nr. 8
Chapter 1 Preparation *1 Cabling Between the Projector and a Hub or computer Use an appropriate cable when connecting the projector and a hub or computer. Connection Ethernet cable type Max. cable length 2 Projector - Hub STP straight-through category 5 * cable 100m (328feet) 2 Projector - Computer STP crossover category 5* cable 100m (328feet) *1 T here may be other limitations depending on your network environment or LAN specification. Please consult your network administrator for further
Inhaltszusammenfassung zur Seite Nr. 9
Flow of installation Flow of installation To use the projector via the networks, follow the setup procedures below. STEP 1 Connect the LAN and set the configuration. Decide depending on the LAN environment. ➔ “2. SetupP rocedures” (pp .11–16). Detailed LAN configurations need to be done with a browser later. First, complete the Wired LAN connection between computers and projec- tors, then start browser configurations. ➔ “3. Basic setting and operation” (pp .17–30). STEP 2 Network Con
Inhaltszusammenfassung zur Seite Nr. 10
Chapter 1 Preparation 10
Inhaltszusammenfassung zur Seite Nr. 11
Chapter 2 2 Setup Procedures Describes how to configure the network. 11 ENGLISH ENGLISH
Inhaltszusammenfassung zur Seite Nr. 12
Chapter 2 Setup Procedures Setting procedures and contents differ depending on the LAN installation location. When installing, consult your system administrator to set up the LAN appropriately. Connecting to an Ethernet cable To connect your projector to a hub which supports 10Base-T/100Base-TX, use a STP (Shield Twisted Pair) straight-through cable having RJ-45 connectors. 1 T urn off the Mains switch. Mains Switch 2 P lug the RJ-45 connector at one end of the cable into the LAN port. 3 P lu
Inhaltszusammenfassung zur Seite Nr. 13
Network configuration Network configuration Set the Wired LAN network through the projector menu. Detailed network settings will be made with browser. Refer to “3. Basic setting and operation” (p.17-30). First, complete the settings described in this chapter before performing steps in “3. Basic setting and opera- tion.” Setting Procedure 1. Select Network icon in the menu bar with the Point 7 8 buttons, and press SELECT button once. 2. Ma ke sure that the Network mode is set to "On". If the m
Inhaltszusammenfassung zur Seite Nr. 14
Chapter 2 Setup Procedures 3. Select "Network setting" in the Network menu with the Point ed buttons and press SELECT button, and then the LAN setting screen will appear and selected LAN settings will be displayed. Adjust each item to the setting environment. Consult your system administrator about the detailed settings. Press the Point 7 8 buttons to move the red frame to an item where you want to adjust, and adjust the figures with the Point ed buttons and move among the items with the P
Inhaltszusammenfassung zur Seite Nr. 15
Network factory default How to enter values with the screen 10-key pallet 1. Select a column with a red frame by using the Point 7 8 buttons. 2. Press the SELECT button. The screen 10-key pallet appears on the 10-key pallet screen. 3. By using the Point de7 8buttons, select numbers 0 to 9 and press SELECT button. By repeating the above to enter the complete number on the column. * To change the number in a column, select “C” and press SELECT button to clear the number in the column and
Inhaltszusammenfassung zur Seite Nr. 16
Chapter 2 Setup Procedures Network information Select "Network information" in the Network menu and press SELECT button to show LAN setting environment of the currently selected projector. (The description below is an example and different from what will be shown.) Network information screen Network information * The numerical value is a setting example. Network factory default 1. Select “Network factory default” in the Network menu and press SELECT button. 2. A confirmation box appears and se
Inhaltszusammenfassung zur Seite Nr. 17
Chapter 3 3 Basic Setting and Operation Describes basic operations and settings for controlling the projec- tor by using the web browser. It is required that computer and projector is connected to the network and the network address is properly configured. 17 ENGLISH ENGLISH
Inhaltszusammenfassung zur Seite Nr. 18
Chapter 3 Basic Setting and Operation Login the setting page of the projector [1] Enter the IP address Launch the web browser installed in your computer, enter the IP address into the "Address" on the browser and then press "Enter" key. Enter the address that you configured in item "Network configuration" ( + pp.13-14). * The numerical value is a setting example. [2] Login I f the setting page has set the password, the authentication window will appear. In this case type "user" onto the Us
Inhaltszusammenfassung zur Seite Nr. 19
Login the setting page of the projector [3] Display of main setting page The following main setting page will be displayed according to your display mode selection. Perform various kinds of settings through this page. Click on the menus to dis- play the control and setting pages. Main setting page in the display Sub menu tab Switches the sub menu tab. Setting page Main menu Displays the control and For selection of control and setting items according to setting items of the projector. t
Inhaltszusammenfassung zur Seite Nr. 20
Chapter 3 Basic Setting and Operation How to use the setting page To control and set up the projector, use the setting menus on the web browser. Describes the basic operation and procedures commonly used on this manual. Example of the setting page The setting menu appears when clicking the sub menu tab. * Each item has a valid setting range respectively. Types of setting Text box setting Enter a number or text and then click Set button. or Change a value with – or + button. Pull-down menu
