Inhaltszusammenfassung zur Seite Nr. 1
MultiSync MT 1020G /820G
LCD Projector
User’s Manual
English
Inhaltszusammenfassung zur Seite Nr. 2
IMPORTANT INFORMATION Precautions Please read this manual carefully before using your NEC MultiSync MT1020G/820G LCD Projector and keep the manual handy for future reference. Your serial number is located next to the main power switch on the back of your MultiSync MT1020G/ 820G . Record it here: CAUTION LASER RADIATION- DO NOT STARE INTO BEAM WAVE LENGTH: 670 nm MAX. OUTPUT: 1 mW CLASS II LASER PRODUCT CAUTION TO PREVENT SHOCK, DO NOT OPEN THE CABINET. NO USER-SER- VICEABLE PARTS INSIDE. REFER
Inhaltszusammenfassung zur Seite Nr. 3
Important Safeguards These safety instructions are to ensure the long life of your LCD Lamp Replacement projector and to prevent fire and shock. Please read them carefully • Be sure to replace the lamp when the Status light comes on. If you and heed all warnings. continue to use the lamp after 2000 hours of use, the lamp bulb may shatter, and pieces of glass may be scattered in the lamp Installation case. Do not touch them as the pieces of glass may cause injury. 1. For best results, use your L
Inhaltszusammenfassung zur Seite Nr. 4
TABLE OF CONTENTS 1. Introduction Introduction To The MultiSync MT1020G/820G LCD Projector ..................E-5 How Do You Get Started? ............................................................................... E-6 What’s In The Box? .........................................................................................E-6 Getting To Know Your MultiSync MT1020G/820G LCD Projector .............E-7 Front Features .............................................................................
Inhaltszusammenfassung zur Seite Nr. 5
1 INTRODUCTION • The "image capture" enables you to use the entire picture This section introduces you to your new MultiSync as a background image or to create an image loop. MT1020G(XGA) or MT820G(SVGA) LCD Projector, pro- vides a list of materials that comes with your projector and • An image can be projected from in front or behind a describes the features and controls. screen, and the projector can even be installed on the ceiling. Congratulations On Your Purchase Of The 2 • Supports most IB
Inhaltszusammenfassung zur Seite Nr. 6
MultiSync MT1020G/820G
LCD Projector User's Manual
Bedienungsanleitung
Manuel d'utilisation
Manuale dell'utente
Manual de uso
Bruksanvisning How Do You Get Started? The fastest way to get started is to take your time and do everything right the first time. Taking a few minutes now to review the manual may save you hours later on. At the beginning of each section of the manual you'll find an overview. If the section doesn't apply, you can skip it. What’s In The Box? Make sure your box conta
Inhaltszusammenfassung zur Seite Nr. 7
Getting To Know Your MultiSync MT1020G/820G LCD Projector Front Features Rear Features Slot for Kensington MicroSaver Security System Terminal Panel Remote Sensor Remote Sensor Lens And Lens Cap PC
DC12V/400mA
REMOTE CONTROL CONTROL OUTPUT INPUT OUTPUT VIDEO INPUT AUDIO INPUT L / MONO
R
S-VIDEO INPUT AUDIO OUTPUT L / MONO
R
RGB INPUT 1 AUDIO RGB MONITOR OUTPUT RGB INPUT 2 AUDIO One-Touch Tilt buttons K Filter Vent Main Power Switch Rear Feet Front Feet AC Input Connect the supplied power
Inhaltszusammenfassung zur Seite Nr. 8
Top Features 1 Power Button FOCUS 7 Use this button to turn the power on and off when Main ZOOM 6 Power Switch is on and the LCD projector is on standby. ADJUST 5 (When this button is pressed and held for at least two ENTER seconds, the “Display Mute” mode will be canceled.) 4 SELECT 3 2 Menu Button MENU 2 Displays the on- screen menu. 1 3 Select Button PUSH POWER
STATUS ON/OFF 9 After you press the “Menu” button, use this button to 8 select the menu icon of the item you wish to adjust. 4 Enter
Inhaltszusammenfassung zur Seite Nr. 9
Terminal Panel Features This panel is located in the rear and is where you connect your cables. 1 Remote Control Jacks 1 a 1 b 2 3 a. Remote Control Input Jack Connect your remote control cable here for wired opera- PC
DC12V/400mA
REMOTE CONTROL tion. CONTROL OUTPUT INPUT OUTPUT b. Remote Control Output Jack This terminal enables you to operate up to five LCD projectors with the same remote control. VIDEO INPUT AUDIO INPUT L / MONO
R When your remote mouse receiver is connected here, the
Inhaltszusammenfassung zur Seite Nr. 10
6 RGB Input 1 Connector (D-Sub 15 pin) Connect your PC or other RGB equipment such as IBM or compatible computers. Use the NEC MultiCable that's PC
DC12V/400mA
REMOTE CONTROL CONTROL OUTPUT supplied to connect to a PC. INPUT OUTPUT RGB 1 Audio Input Mini Jack VIDEO INPUT AUDIO INPUT This is where you connect RGB audio output from a L / MONO
R
computer or another RGB source. 7 RGB Input 2 Connector (Mini D-Sub 15 pin) S-VIDEO INPUT AUDIO OUTPUT Connect a Macintosh or compatible computer here
Inhaltszusammenfassung zur Seite Nr. 11
Remote Control Features You can use your remote control with the cable or wireless 1 to operate your MultiSync MT1020G/820G LCD Projector. With the remote mouse receiver connected to your com- 2 puter, you can also use the projector's remote control to operate your computer's mouse wireless, too. (See page E- 20 to connect the remote mouse receiver to your computer.) If you want to use your remote control with the cable, connect one end of the cable to the jack on the remote control and the othe
Inhaltszusammenfassung zur Seite Nr. 12
B Menu Button Use this button to call up the On-Screen Menu so you can adjust and set the image. After you press this button, it OFF ON POWER will light up. During this time you can use the mouse pointer and right / left click buttons to make menu selec- VIDEO S-VIDEO VOLUME tions. If no buttons are pressed within 10 seconds while it + illuminates, the light goes out. To return to the main menu RGB 1 RGB 2 from a sub menu, press this button again. –
MENU LASER C Mouse Pointer Buttons B Works as
Inhaltszusammenfassung zur Seite Nr. 13
2 INST ALLA TION This section describes how to set up your MultiSync Carrying handle MT1020G/820G LCD projector and how to connect video and audio sources. Setting Up Your MultiSync MT1020G/820G LCD Projector Push to release the Your MultiSync MT1020G/820G LCD Projector is simple handle. to set up and use. But before you get started, you must first: 1. Determine the image size 2. Set up a screen or select a non-glossy w
Inhaltszusammenfassung zur Seite Nr. 14
(A) Top view Using A Tabletop Or Cart Screen 1. Place your LCD projector on a flat level surface at the optimal distance from the screen or wall so you realize the size image you want. (Avoid having bright room lighting or sun light directly on the screen or wall where you'll be projecting the image.) 2. Connect the power cable, remove the lens cap and turn the projector on. (If no input signal is available, the projector will display a background image.) (B) Side view Screen 3. Ensure that the
Inhaltszusammenfassung zur Seite Nr. 15
Screen size = diagonal(inch) Optical axis center line 235”-300” 165”-222” 115”-150” 77”-100” 47”-60” 20”-27” 0.5 mm 0 Screen center line 6.5° (Telephoto) 8.5° 1 m 2.4 m Screen center line (Wide) 4 m 6 m 8 m 12.2 m 4 mm 12 11 10 9 8 7 6 5432 1 0 (m) Distance from lens surface Note: Distances may vary ± 5%. • Ensure that you have adequate ventilation around your WARNING LCD projector so heat can dissipate. Do not cover the • Only use your LCD projector on a solid, level surface. If vents on t
Inhaltszusammenfassung zur Seite Nr. 16
Wiring Diagram DC12V/400mA
PC
REMOTE CONTROL CONTROL OUTPUT INPUT OUTPUT Document Camera VIDEO INPUT AUDIO INPUT L / MONO
R
S-VIDEO INPUT AUDIO OUTPUT To video, S-video, L / MONO
R
and audio inputs on RGB INPUT 1 AUDIO To AC power the LCD projector. RGB MONITOR OUTPUT © VCR or LaserDisk Player RGB INPUT 2 AUDIO output IBM/MAC MultiCable To mini D-Sub 15-pin or D-Sub 15-pin connector on the LCD Projecto
Inhaltszusammenfassung zur Seite Nr. 17
Connecting Your PC Or Macintosh Computer Connecting your PC or Macintosh computer to your MultiSync MT1020G (XGA) / 820G (SVGA) LCD Projector will enable you to project your computer's screen image for an impressive presenta- tion. All of these following display standards are supported: VGA 6402480 for graphics VGA 6402400 for graphics VGA 6402350 for graphics VGA 7202400 for text VGA 7202350 for text SuperVGA 8002600 XGA 10242768* Macintosh at 10242768* Macintosh at 6402480 Macintosh at 8322624
Inhaltszusammenfassung zur Seite Nr. 18
Changing Video Resolutions Windows 3.1 Depending on your computer's graphic capability, you may 1. Click on the "Main" icon and open "Control Panel." be able to select one of several resolutions. Generally a 2. Select "Change System Settings" and click on "Option." computer- either a PC or Macintosh- with 1 meg. of memory 3. Choose "Change Display Settings." will run: 4. Select the resolution you want. 640 x 480 at 16.7 million colors (24 bit Truecolor) 5. Choose the current drive or another. 80
Inhaltszusammenfassung zur Seite Nr. 19
Connecting Your Document Camera You can connect your MultiSync MT1020G/820G LCD Projector to a document camera. To do so, simply: 1. Turn off the power to your LCD projector and document camera. 2. Use a standard video cable to connect your document camera to the Video input on your projector. 3. Turn on the LCD projector and the document camera. NOTE: Refer to your document camera's owner's manual for more information about your camera's video output requirements . Connecting Your VCR Or Lase
Inhaltszusammenfassung zur Seite Nr. 20
Connecting Your Remote Mouse Receiver The remote mouse receiver enables you to operate your computer's mouse functions from the NEC MultiSync MT1020G/820G remote control. It is a great convenience for clicking through your computer-generated presentations. To connect the remote mouse receiver: 1. Turn off your computer. 2. For PCs: Remove your current mouse and connect the serial cable from the remote mouse receiver to your PC's mouse port. (Use the 6-pin adapter for connecting to a PS/2 compute
