Bedienungsanleitung Jenn-Air Dual Fuel Cooktop

Inhaltszusammenfassung zur Seite Nr. 1

EXPRESSIONS WUENN-AIR
DUAL FUEL COOKTOP 403 WE FOURTH STSTFtEET flORTHe , tAS flE3 020 NT8 ON,
IMPORTANT: Installation should be performed only by a Jenn-Air AuthorizedServicer orother qualified installer.Read safety
precautions inthe Use & Care Manual before usingthis appliance.
imensions shown in beth inches and centimeters.)
• 31 7/8" +1 9/16" _:1/16"
[80.96 ¢m] [52.23 cm]
7/8"
22.54 crn_ 36.67
2 1/4 ° MIN.
GAS CONNECTION [2.54 ¢m] [5.71 cm]
AXIS -'7 MIN.
I CLEARANCE
8 7/8"
[22.54 ¢m]
5 13/16

Inhaltszusammenfassung zur Seite Nr. 2

Location Of Your Jenn-Air Appliance Preparation Of Countertop Locatethis applianceaway from combustiblematerials such The cutout inthe countertop intowhich the applianceis to be as window curtains and combustible wall decorations. The installed should be prepared according to the cutout minimum horizontal clearance between the edge of the dimensions given on page 1 of these instructions. applianceand adjacentcombustibleconstructionis: • 0.75 inches (1.90cm) at rear; CAUTION: Cutout dimensions ar

Inhaltszusammenfassung zur Seite Nr. 3

Connecting Appliance To Electricity Connecting Appliance To Gas Supply Electrical Wiring Information A TRAINED SERVICEMAN OR GAS APPLIANC INSTALLER MUST MAKE THE GAS SUPP[ The neutral of this unit is grounded to the frame through the CONNECTION. Leak testing of the appliance shall t green grounding wire. If local conditions do not permit conducted by the installer according to the instructior grounding of the neutral, untwist or disconnect the green wire given. and connect the green wire to grou

Inhaltszusammenfassung zur Seite Nr. 4

NOTE: In Canada, gas utilization codes prohibit use of street Step 3: Trim a small piece of masking tape to the size of elbows. Use standard pipe elbows and make modifications to a dime and affix it over the end of a 5/16" nut these instructions as necessary, driver. Pressure Testing Step 4: Firmly press the nut driver over the orifice spud (figure 5) and loosen spud by turning This appliance must be isolated from the gas supply piping counterclockwise. Carefully lift nut driver out of system by

Inhaltszusammenfassung zur Seite Nr. 5

Installation of LP Orifice Spuds With a quarter, engage slot and rotate cap 1/8 of a tL counterclockwise. To remove cap, turn cap over and reinst_ _ . (_ = ° 00 NaturalSetting LP Setting L Figure8: Conversionof Harper-Wyman P"" 0 Appliance PressureRegulator // "_ _ _ After conversion, steps A and B have been completed, che¢ ART#9215-033-0 the appearance of each burners' flame at the Hi and L small, review all steps to make sure they were complete correctly. settings against figure 9. If the flam

Inhaltszusammenfassung zur Seite Nr. 6

To Convert Appliance For Use With Installation of Natural Gas Orifice Spuds Natural Gas This appliance is equipped for electronic auto-reignition by Ifthis appliance has been converted for use with LP gas, each means of a spark igniter located at the side of each burner. The of the following modifications must be performed to convert burners are designed to light at any valve rotation that admits the unit back to natural gas. sufficient gas flow to support a flame and to automatically re-light f