Bedienungsanleitung Bosch Appliances NWC-0700

Inhaltszusammenfassung zur Seite Nr. 1

1 en | Bosch Security Systems Megapixel IP Cameras
Important Safety Instructions
Type numbers: NWC-0700, NWC-0800, NWC-0900
Read, follow, and retain all of the following safety instructions. Heed all
warnings on the unit and in the operating instructions.
1. Clean only with a dry cloth. Do not use liquid cleaners or aerosol clean-
ers.
2. Do not install unit near any heat sources such as radiators, heaters,
stoves, or other equipment (including amplifiers) that produce heat.
3. Do not block an

Inhaltszusammenfassung zur Seite Nr. 2

Megapixel IP Cameras Quick Install Guide | en 2 CAUTION! Indicates a potentially hazardous situation. If not avoided, this may result in property damage or risk of damage to the unit. NOTICE! This symbol indicates information or a company policy that i relates directly or indirectly to the safety of personnel or protection of property. CAUTION! – U.S.A. models only - Section 810 of the National Electrical Code, ANSI/NFPA No. 70, provides information regarding proper grounding of the mou

Inhaltszusammenfassung zur Seite Nr. 3

3 en | Bosch Security Systems Megapixel IP Cameras FCC & ICES INFORMATION (U.S.A. and Canadian Models Only) This device complies with part 15 of the FCC Rules. Operation is subject to the following conditions: – this device may not cause harmful interference, and – this device must accept any interference received, includ- ing interference that may cause undesired operation. NOTICE! This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to Pa

Inhaltszusammenfassung zur Seite Nr. 4

Megapixel IP Cameras Quick Install Guide | en 4 1 Quick Install Guide 1.1 Camera installation using PoE switch Equipment needed: – PC with 100baseT or better network port – 100 baseT or better network switch with PoE capability –2 CAT5 Network cables CAUTION! Never supply power via the Ethernet connection (PoE) when ! power is already supplied via the power connector. 1. Attach camera to a PoE port of the network switch with CAT5 cable. 2. Attach (non-PoE) switch port to the PC LAN port with

Inhaltszusammenfassung zur Seite Nr. 5

5 en | Bosch Security Systems Megapixel IP Cameras 1. Attach camera to the 100 Mbps network input of the PC with the cross-link CAT 5 cable. 2. Manual iris lens: check the lens to make sure the F-Stop is between F2.8 and F4.0. 3. DC-iris lens: plug in the DC-iris cable into the iris connec- tor on the rear of the camera. 4. Plug in the camera power cord. 5. A yellow LED on the back of the camera should light up after a few seconds. – This LED indicates that a link to the computer has been es

Inhaltszusammenfassung zur Seite Nr. 6

Megapixel IP Cameras Quick Install Guide | en 6 Basic mode 1. Click Automatic. The install program will scan the network for all connected MegaPixel cameras and assign an IP address automatically within the network segment of the host PC. When all the connected cameras show 'Success' in the Results column, the installation process is complete. 2. Write down the (MAC) Ethernet address, corresponding IP address, and installed location. 3. Click Save / Exit when done. Fig. 1.1 Camera installat

Inhaltszusammenfassung zur Seite Nr. 7

7 en | Bosch Security Systems Megapixel IP Cameras Fig. 1.2 Camera installation in advanced mode showing results Advanced mode 1. Start making a list of Ethernet (MAC) addresses and IP addresses assigned to them. The Ethernet address is on the camera label. 2. Click Find Cameras. 3. Select a camera by clicking its Ethernet address. 4. Enter the IP address assigned to that camera in the New Camera IP box. 5. Click Set IP. 6. Click Automatic. 7. Wait for result to change from unchecked to succe

Inhaltszusammenfassung zur Seite Nr. 8

Megapixel IP Cameras Quick Install Guide | en 8 b. Rotate lens in or out with back focus ring until focus is obtained. c. Fasten the two set screws. Bosch Security Systems Quick Install Guide F.01U.032.595 | V 1.0 | 2007.03