Inhaltszusammenfassung zur Seite Nr. 1
INSTRUCTION MANUAL
Cilo C-102AV-Receiver
Inhaltszusammenfassung zur Seite Nr. 2
02
Inhaltszusammenfassung zur Seite Nr. 3
Tableofcontents TABLE OF CONTENTS OPERATION AND FUNCTIONS Table of contents 03 STANDBY 15 Selection of input source 15 IMPORTANT INSTRUCTIONS Loudspeaker setup 16 DSP, Mode, Mute and Bass Boost 16 Important safety instructions 04 Selection of input signal 17 Use of radio (tuner) 17 REMOTE CONTROL Manual and automatic tuning 18 Storing of radio stations 18 Installation of batteries 05 Selection of station and RDS 18 Using the remote control 05 Selection of digital optical/coaxial inputs 19 Remote
Inhaltszusammenfassung zur Seite Nr. 4
Impor tant safety instructions Congratulations on your new AV receiver. Please read this manual carefully to avoid malfunction and damage to the receiver and to ensure that the receiver will be a source of great pleasure to you for a very long time. Important safety instructions 1. Do not expose the receiver to direct sunlight, 10. Do not use corrosive or strong cleaning agents. high humidity, dirt, heavy vibration or extreme Make sure that no moisture penetrates the temperatures. receiver durin
Inhaltszusammenfassung zur Seite Nr. 5
Remote control Installation of batteries Remove the cover as illustrated. Replace the cover. Insert two batteries of the type AAA/R03/UM4. Make sure that the terminals correspond to the symbols shown (see bottom). Do not mix new and old batteries, and do not use different types of batteries. If the remote control is not used for prolonged periods, remove the batteries from the remote control to prevent corrosion. Using the remote control VOLUME Aim the remote control at the sensor on the STANDBY
Inhaltszusammenfassung zur Seite Nr. 6
Remote control Remote control functions 1. Standby 2. Digital Optical Input STANDBY 3. Digital Coaxial Input 4. AUX 1 5. TV 6. RDS 7. Band (FM/AM) 8. DSP mode 9. SPK mode (Speaker mode) 10. Balance 11. Center delay + 12. Center delay - 13. Tuning up SPEAKER 14. Tuning mode 15. Preset - 16. Tuning down 17. Mute 18. Volume decrease 19. AUX 2 20. Tuner 21. Memory 22. Mono/Stereo (FM) 23. Night (Dynamic Compression) 24. Test 25. Mode [Stereo/PL II Musik/ PL II Movie, DTS/Dolby Digital] 26. Surround
Inhaltszusammenfassung zur Seite Nr. 7
Front panel and connections Front panel VOLUME STANDBY MODE DSP INPUT TUNING BAND HEADPHONE SPEAKER A SPEAKER B 12 3 4 5 678 9 10 11 12 1. Standby On/Off 7. Input selector 2. Standby LED 8. Speaker B selector 3. Headphone 9. Tuning 4. Mode (Dolby Digital, 10. Band (FM/AM) DTS, PL II Movie, 11. Display PL II Music, Stereo) 12. Multijog 5. DSP Program 6. Speaker A selector Connections AV RECEIVER MODEL:CiloC-102 ITEM NO.: 11098.01 POWER SOURCE: 220-240V~50/60Hz POWER CONSUMPTION: 200W MAX SERIAL N
Inhaltszusammenfassung zur Seite Nr. 8
System setup The receiver shall not be connected to the mains supply before all other system connections have been made. Outline of audio/video connections The receiver is provided with two analogue and two digital audio/video inputs. A video or digital camera may e.g. be connected through the analogue audio/video inputs. The DVD player is connected through the digital inputs (optical or coaxial). The video signal is transmitted to the television set through the SCART connection. It is also poss
Inhaltszusammenfassung zur Seite Nr. 9
System setup Connection through analogue audio/video cable The audio/video jacks of the video camera are connected to the Cilo AV receiver through an audio/video cable. As you wish to see the film through your television set, the camera must also be connected to the television set. Use the SCART cable for this purpose (see illustration). For simplicity, the individual conductors have been marked by different colours. 3 X RCA audio video cable Stereo camcorder VHS Minidisc- or Mp3-player SCART Ca
Inhaltszusammenfassung zur Seite Nr. 10
System setup Connection through digital audio/video cable The DVD player's coaxial or optical digital output must be connected with the corresponding digital input on the AV receiver (OPT/COAX). Make sure always to use the corresponding video input! Switch to the corresponding signal source by means of the INPUT key. Video cable Coaxial cable DVD-Player Optical cable Digital satelite receiver Most DVD players with digital outputs are factory-set at the PCM data format. Make sure that the DVD pla
Inhaltszusammenfassung zur Seite Nr. 11
System setup Loudspeaker arrangement Before connecting the loudspeakers, these should be positioned correctly. Correct positioning is crucial to ensure optimal sound. The optimal location depends on the characteristics of the room and the walls. The illustration below shows an example of a speaker arrangement. 1. Listening position 5. Left front speaker 2. Right front speaker 6. Subwoofer 3. TV 7. Right surround speaker 4. Centre speaker 8. Left surround speaker The front and centre speakers sho
Inhaltszusammenfassung zur Seite Nr. 12
System setup Installation of AM antenna Install the AM antenna by mounting it on the fixing device (see illustration). Place the antenna in the position where the best signal is received, as far away from the system, the television set and the cables as possible. If the signal quality is not satisfactory, an outdoor antenna may be required. Connection of AM antenna Connect the two loop antenna wires to the inputs marked AM (see illustration). Press the corresponding button (1), insert the bare c
Inhaltszusammenfassung zur Seite Nr. 13
System setup Installation and connection of FM antenna Connect the FM indoor antenna to the antenna connection marked FM 75. For this purpose, place the cable shoe on the pin in the middle of the connecting bush. Tune in to a station and place the antenna in the position where the best and clearest signal is received. If the signal quality is not satisfactory, an outdoor antenna may be required. FM cable connection If you have cable television, the cable network radio connection may also be conn
Inhaltszusammenfassung zur Seite Nr. 14
System setup Connection to the mains supply AV RECEIVER MODEL: Cilo C-102 ITEM NO.: 11098.01 POWER SOURCE: 220-240V~50/60Hz POWER CONSUMPTION: 200W MAX SERIAL NO.: FM-ANTENNA-AM RL RL SPEAKER A SPEAKER B CEN. SW SR SL FRONT SPEAKER OUTPUT OPT. VIDEO COAX VIDEO AUX 1 AUX 2 SUB SCART INPUT/OUTPUT SPEAKER OUTPUT Do not connect the receiver to the mains supply before all system connections have been made correctly. Check that all connections have been made correctly before connecting the receiver to
Inhaltszusammenfassung zur Seite Nr. 15
Operation and functions Standby 1 Press the STANDBY key of the remote control to switch to standby mode. The display is switched off and all functions are reduced to a minimum. Thus the power consumption of the receiver is reduced to a minimum. In standby mode the receiver only responds to the STANDBY key of the remote control. STANDBY STANDBY MODE DSP INPUT TUNING BAND 1 1 C-102 HOME THEATRE RECEIVER DIGITAL DVD/SAT 2 1 TV AUX 1 AUX 2 TUNER Consider the environment and switch off the unit after
Inhaltszusammenfassung zur Seite Nr. 16
Operation and functions Loudspeaker setup 1 Press the VOL+ key to increase the volume, press the VOL- key to decrease the volume. BAND RDS MEMORY MONO 2 Turn Multijog to the right to increase the volume and SPK DSP to the left to decrease the volume MODE MODE NIGHT TEST 3 4 Press the BALANCE key repeatedly and then the CENTER BALANCE MODE REAR VOL+/- keys to adjust the volume for all channels. + + 3 DELAY SPEAKER DELAY This way you control the balance of the front - - speakers and the volume of
Inhaltszusammenfassung zur Seite Nr. 17
Operation and functions Selection of input signal Press the DIGITAL 1/DIGITAL 2/TUNER/AUX1/AUX2/TV key to select the corresponding input. Press the INPUT key on the front panel repeatedly to switch between the following inputs: DIGITAL STANDBY 1/DIGITAL 2/TUNER/AUX1/AUX2/TV. DIGITAL DVD/SAT 1 2 TV AUX 1 AUX 2 TUNER BAND RDS MEMORY MONO STANDBY MODE DSP INPUT TUNING BAND SPK DSP MODE MODE NIGHT TEST C-102 HOME THEATRE RECEIVER Use of radio (tuner) Press the TUNER key on the remote control or the
Inhaltszusammenfassung zur Seite Nr. 18
Operation and functions Manual and automatic tuning SPK DSP TEST MODE MODE NIGHT CENTER BALANCE MODE REAR Press the TUNING key to switch between "TUN + + SPEAKER DELAY DELAY STEP" (manual) and "TUN SCAN" (automatic). - - Press either the TUNING UP key or the TUNING TUNING + DOWN key to start searching. MANUAL PR - PR + The search function may also be activated directly AUTO from the front panel. Press the TUNING key and start BASS searching by means of the Multijog. MUTE TUNING - BOOST VOLUME St
Inhaltszusammenfassung zur Seite Nr. 19
Operation and functions Selection of digital optical / coaxial inputs Press the DIGITAL 1/DIGITAL 2 keys to activate the DIGITAL DVD/SAT digital inputs. Check that the Setup (digital output) of 2 1 the peripheral devices are set at RAW and bitstream respectively. TV AUX 1 AUX 2 TUNER Depending on the size of the room, the speakers may BAND RDS MEMORY MONO be configured through CENTRE DELAY and SURROUND DELAY. SPK DSP MODE MODE NIGHT TEST Selection is also possible through the front panel by pres
Inhaltszusammenfassung zur Seite Nr. 20
Te c h n i c a l d a t a Frequency respons 20-20.000Hz S/N >105dB THD <0.1% Digital inputs Optical and coaxial Analog input RCA Video input RCA Power 220-240V~50/60Hz Power consumption 200W Music power 5x60W+1x 100W Measures 430 x 68 x 330mm Weight ca. 6kg. We reserve the right to change the technical data and design without notice as a result of further development. 20
