Bedienungsanleitung EMC DS-xxB2

Bedienungsanleitung für das Gerät EMC DS-xxB2

Gerät: EMC DS-xxB2
Kategorie: Umschalter
Produzent: EMC
Größe: 0.92 MB
Datum des Hinzufügens: 1/15/2014
Seitenanzahl: 22
Anleitung drucken

Herunterladen

Wie kann man es nutzen?

Unser Ziel ist Ihnen einen schnellen Zugang zu Inhalten in Bedienungsanleitungen zum Gerät EMC DS-xxB2 zu garantieren. Wenn Sie eine Online-Ansicht nutzten, können Sie den Inhaltsverzeichnis schnell durchschauen und direkt zu der Seite gelangen, auf der Sie die Lösung zu Ihrem Problem mit EMC DS-xxB2 finden.

Für Ihre Bequemlichkeit

Wenn das direkte Durchschauen der Anleitung EMC DS-xxB2 auf unserer Seite für Sie unbequem ist, können sie die folgende zwei Möglichkeiten nutzen:

  • Vollbildsuche – Um bequem die Anleitung durchzusuchen (ohne sie auf den Computer herunterzuladen) können Sie den Vollbildsuchmodus nutzen. Um das Durchschauen der Anleitung EMC DS-xxB2 im Vollbildmodus zu starten, nutzen Sie die Schaltfläche Vollbild
  • Auf Computer herunterladen – Sie können die Anleitung EMC DS-xxB2 auch auf Ihren Computer herunterladen und sie in Ihren Sammlungen aufbewahren. Wenn Sie jedoch keinen Platz auf Ihrem Gerät verschwenden möchten, können Sie sie immer auf ManualsBase herunterladen.
EMC DS-xxB2 Handbuch - Online PDF
Advertisement
« Page 1 of 22 »
Advertisement
Druckversion

Viele Personen lesen lieber Dokumente nicht am Bildschirm, sondern in gedruckter Version. Eine Druckoption der Anleitung wurde ebenfalls durchdacht, und Sie können Sie nutzen, indem Sie den Link klicken, der sich oben befindet - Anleitung drucken. Sie müssen nicht die ganze EMC DS-xxB2 Anleitung drucken, sondern nur die Seiten, die Sie brauchen. Schätzen Sie das Papier.

Zusammenfassungen

Unten finden Sie Trailer des Inhalts, der sich auf den nächsten Anleitungsseiten zu EMC DS-xxB2 befindet. Wenn Sie den Seiteninhalt der nächsten Seiten schnell durchschauen möchten, können Sie sie nutzen.

Inhaltszusammenfassungen
Inhaltszusammenfassung zur Seite Nr. 1

EMC Departmental Switch
DS-xxB2
Guide for Installation of Switches
Into Third-Party Racks
P/N 300-000-267
Rev. A02
November 7, 2002
This document describes the requirements for installing EMC
Deparmental Switches (DS-xxB2) into both EMC and non-EMC
third-party racks.
Major sections discussed in this guide are as follows:
 Overview ................................................................................................2
 Device Power, Cooling, and Weight Information.................

Inhaltszusammenfassung zur Seite Nr. 2

Overview Overview The Departmental Switch Models DS-16B2 and DS-32B2 are fibre channel gigabit switches that support link speeds up to 2 Gb/s. Each port can automatically negotiate to the highest common speed of all devices connected to the port. The ports are compatible with small form factor pluggable media (SFPs), are universal, self configuring, and are capable of individually becoming a fabric-enabled port (F_Port), fabric loop enabled port (FL_Port), or an expansion port (E_Port). T

Inhaltszusammenfassung zur Seite Nr. 3

Device Power, Cooling, and Weight Information Device Power, Cooling, and Weight Information Table 2 lists the power and cooling requirements and weight information for the DS-16B2 and DS32B2 switches. Table 2 Device Power, Cooling, and Weight Information Cooling Requirements Device Power Requirements (Heat Dissipation) Maximum Weight DS-16B2 switch Voltage: 100 to 240 V ac, 47 to 63 Hz 368.5 BTU/hr 12.9 kg (28.5 lbs) DS-32B2 switch Voltage: 100 to 240 V ac, 47 to 63 Hz 1876 BTU/hr 16.2 kg (35

Inhaltszusammenfassung zur Seite Nr. 4

Device Placement Requirements Device Placement Requirements There are no restrictions on the location of the DS-xxB2 switch in the rack/cabinet. Switches are typically located at the top of the rack/cabinet. Power distribution must support the number of outlets required for the switch and the switch power rating listed in Table 2 on page 3. Front Rear EMC2056S Figure 2 Sample Cabinet Installation 4 EMC Departmental Switch DS-xxB2 Into Third-Party Racks

Inhaltszusammenfassung zur Seite Nr. 5

Switch Mounting Kit (DS16B2RKLS) Switch Mounting Kit (DS16B2RKLS) The switch mounting kit includes rails, and brackets as listed inTable 4. Table 4 Switch Mounting Kit Component Use 2 switch mounting brackets (see Figure 15 on page 17) 2 per switch 2 short rail assemblies (20.5 inches to 27 inches) 2 per switch 2 long rail assemblies (27 inches to 34 inches) 2 per switch Figure 3 illustrates these components. Switch Front Mounting Rails Brackets Short Long Rear Rear Rails Rails EMC2042S Figure

Inhaltszusammenfassung zur Seite Nr. 6

Switch Mounting Kit (DS16B2RKLS) Screws, Nuts and Washers Table 5 lists all the securing hardware that is included in the switch mounting kit. Table 5 Screws, Nuts and Washers Component Use #10 flat washer (Qty. 4) 2 per rail assembly to secure adjustable rail to the “C” channel. M5 keps nut (Qty. 4) 2 per rail assembly to secure adjustable rail to the “C” channel. 8-32 x 5/16-in. pan-head screw (Qty. 6) 3 per mounting bracket to secure mounting bracket to switch. M5 x 10-mm pan-head screw (

Inhaltszusammenfassung zur Seite Nr. 7

Switch Mounting Kit (DS16B2RKLS) Tools Required for Installation You will need the tools shown in Figure 4 to complete the installation of the rails and one or more switches. Tools Required: #1 Phillips 6-mm (1/4-in.) 8mm (5/16-in.) Screwdriver Nut Driver Nut Driver EMC2065 Figure 4 Tools Required for Installation EMC Departmental Switch DS-xxB2 Into Third-Party Racks 7

Inhaltszusammenfassung zur Seite Nr. 8

Installing the DS-xxB2 Rails Installing the DS-xxB2 Rails This section describes the installation procedures for the DS-xxB2 rails. Figure 5 shows a view of the rails installed in a 39 U rack/cabinet. Rear Door Removed for Clarity EMC2071S Front Rear Figure 5 View of the Rails Installed in a 39 U Rack/Cabinet 8 EMC Departmental Switch DS-xxB2 Into Third-Party Racks

Inhaltszusammenfassung zur Seite Nr. 9

Installing the DS-xxB2 Rails DS-xxB2 Rails Installation There are two different length rails, see Figures 6 and 7. The short rails range between 20.5 inches and 27 inches. The long rails range between 27 inches and 34 inches. If your rail kit contains two different length rear rail mounts, be sure to use the rail length that is appropriate for your rack/cabinet. To the rear of the cabinet EMC2059 Figure 6 DS-xxB2 Short Rear Rails To the rear of the cabinet EMC2060 Figure 7 DS-xxB2 Long Rear

Inhaltszusammenfassung zur Seite Nr. 10

Installing the DS-xxB2 Rails The front and rear flanges of the DS-xxB2 rails have three screw holes. See Figures 8 and 9. Front Rails Screw Holes EMC2069 Figure 8 Front Flange of the DS-xxB2 Rails Screw Holes Screw Holes Short Rear Rails Long Rear EMC2070 Rails Figure 9 Rear Flange of the DS-xxB2 Rails 10 EMC Departmental Switch DS-xxB2 Into Third-Party Racks

Inhaltszusammenfassung zur Seite Nr. 11

Installing the DS-xxB2 Rails Select the appropriate length rails, and follow the steps below to install them. The rails assembly consists of a front rail, an adjustable rear rail, and two washers and keps nuts. Figure 10 illusrates the complete assembly. Keps Nut (2) #10 Flat Washer (2) Short Rear Rail Front Rail #10 Flat Washer Keps Nut Front Short (2) (2) Rail Rear Rail EMC2044S Figure 10 DS-xxB2 Rails Assembly EMC Departmental Switch DS-xxB2 Into Third-Party Racks 11

Inhaltszusammenfassung zur Seite Nr. 12

Installing the DS-xxB2 Rails Assembling the Rails To assemble the rails: 1. Place the front rail down on a table. 2. Insert the slots of the rear adjustable rail onto the threaded posts on the front rail. Be sure that the lip on the top of the rear adjustable rail slides over the top of the slot on the front rail, thereby capturing the ac power cord. 3. Secure the adjustable rail to the front rail with two #10 flat washers and M5 keps nuts. Leave the keps nuts finger tight (see Figure 11).

Inhaltszusammenfassung zur Seite Nr. 13

Installing the DS-xxB2 Rails Keps Nut Keps Nut EMC2045S Figure 12 Securing the Keps Nuts If the side skins are removed on the rack/cabinet, the keps nuts can be tightened after the rails have been installed. Round-Hole Channel To install the rails assembly in the round-hole channel of the rack/cabinet: 1. Align the holes of the front rail flange to the inside of the front channel. The top and bottom screw holes are used for the screws. 2. Secure the rail to a round-hole channel with 2 M5 x

Inhaltszusammenfassung zur Seite Nr. 14

Installing the DS-xxB2 Rails Align the rear rail flange to the inside of the channel. Rack Rear Align the front rail flange to the inside Rack Rear of the channel. Front M5 x 10-mm Pan Head Screw (8) Front EMC2046S Figure 13 Installing Rails in Round-Hole Channels 14 EMC Departmental Switch DS-xxB2 Into Third-Party Racks

Inhaltszusammenfassung zur Seite Nr. 15

Installing the DS-xxB2 Rails Square-Hole Channel To install the rails assembly in the square-hole channel of the rack/cabinet. 1. Align the holes of the front rail flange to the inside of the front channel. The top and bottom screw holes are used for the screws (see Figure 14 on page 16). 2. Secure the rail to a square-hole channel with two square-hole washers and M5 x 16-mm flat-head screws (see Table 5 on page 6). Leave the screws finger-tight, and tighten them after the switch is insta

Inhaltszusammenfassung zur Seite Nr. 16

Installing the DS-xxB2 Rails Align the rear rail flange to the inside Rack of the channel. Rear Align the front rail Rack flange to the inside Front of the channel. M5 x 16-mm flat head screw (Qty. 8) Square-Hole Washer (Qty. 8) EMC2047S Figure 14 Installing Rails in Square-Hole Channels 16 EMC Departmental Switch DS-xxB2 Into Third-Party Racks

Inhaltszusammenfassung zur Seite Nr. 17

Installing the DS-xxB2 Switch Installing the DS-xxB2 Switch This section describes the procedures for installing the DS-xxB2 switch in a rack/cabinet, including attaching the brackets on the switch. Mounting Bracket Installation You must attach mounting brackets to the switch before installing it on the rails. The mounting brackets slide into the “C” channel of the rails. To attach the mounting brackets to the switch: 1. Orient the L-shaped end of the bracket outward and to the power outle

Inhaltszusammenfassung zur Seite Nr. 18

Installing the DS-xxB2 Switch Installing the Switch in the Rack/Cabinet To install the switch in the rack/cabinet: 1. Lift and orient the switch so that the fan end is to the front of the rack/cabinet. 2. Align the bracket on each side of the switch with the “C” channel on each fixed rail. 3. Push the switch into the rack/cabinet until the hole in the front part of each bracket (the “L”-shaped end) aligns with the hole on the fixed rail. EMC2049S Figure 16 Placing the Switch Into the Rack/C

Inhaltszusammenfassung zur Seite Nr. 19

Installing the DS-xxB2 Switch M3 x 8-mm Pan Head Screw (2) EMC2050S Figure 17 Securing the brackets to the Rails 5. Tighten the rear screws securing the rails to the rear of the rack/cabinet (see Figure 18 on page 20). 6. Tighten the front screws securing the rails to the front of the rack/cabinet (see Figure 18). EMC Departmental Switch DS-xxB2 Into Third-Party Racks 19

Inhaltszusammenfassung zur Seite Nr. 20

Installing the DS-xxB2 Switch Rail Assembly Screw (4) Rail Assembly Screw (4) EMC2051S Figure 18 Tightening the Front and Rear Rail Assembly Screws 20 EMC Departmental Switch DS-xxB2 Into Third-Party Racks


Ähnliche Anleitungen
# Bedienungsanleitung Kategorie Herunterladen
1 EMC DS-16B2 Handbuch Umschalter 12
2 EMC DS-16B Handbuch Umschalter 1
3 EMC DS-8B Handbuch Umschalter 2
4 Sony 4-296-436-11 (2) Handbuch Umschalter 0
5 3Com 10/100BASE-TX Handbuch Umschalter 61
6 3Com 2226-SFP Handbuch Umschalter 688
7 3Com 16985ua.bk Handbuch Umschalter 10
8 3Com 10BASE-T Handbuch Umschalter 4
9 3Com 10BASE-2 Handbuch Umschalter 1
10 3Com 1000BASE Handbuch Umschalter 6
11 3Com 2226 PLUS Handbuch Umschalter 473
12 3Com 2250-SFP Handbuch Umschalter 538
13 3Com 1600 Handbuch Umschalter 0
14 3Com 2924-PWR Handbuch Umschalter 72
15 Sony BZPS-8001 Handbuch Umschalter 1