Inhaltszusammenfassung zur Seite Nr. 1
54/108Mbps Super G Wireless LAN
Managed Access Point
WAP-4060PE
User’s Manual
Inhaltszusammenfassung zur Seite Nr. 2
Copyright Copyright 2005 by PLANET Technology Corp. All rights reserved. No part of this publica- tion may be reproduced, transmitted, transcribed, stored in a retrieval system, or translated into any language or computer language, in any form or by any means, electronic, mechani- cal, magnetic, optical, chemical, manual or otherwise, without the prior written permission of PLANET. PLANET makes no representations or warranties, either expressed or implied, with respect to the contents
Inhaltszusammenfassung zur Seite Nr. 3
R&TTE Compliance Statement This equipment complies with all the requirements of DIRECTIVE 1999/5/CE OF THE EUROPEAN PARLIAMENT AND THE COUNCIL OF 9 March 1999 on radio equipment and telecommunication terminal Equipment and the mutual recognition of their conformity (R&TTE) The R&TTE Directive repeals and replaces in the directive 98/13/EEC (Telecommunications Terminal Equipment and Satellite Earth Station Equipment) As of April 8,2000. Safety This equipment is designed with the utmost
Inhaltszusammenfassung zur Seite Nr. 4
TABLE OF CONTENTS CHAPTER 1 INTRODUCTION..........................................................................1 1.1 Package Contents...........................................................................................1 1.2 System Requirements ....................................................................................1 1.3 Features ...........................................................................................................1 1.4 Physical Details............
Inhaltszusammenfassung zur Seite Nr. 5
4.6.2 802.1x Authentication Setup .................................................................. 49 4.7 Using 802.1x Mode (without WPA).............................................................. 52 CHAPTER 5 OPERATION AND STATUS ...................................................... 53 5.1 Operation ....................................................................................................... 53 5.2 Status Screen .............................................................
Inhaltszusammenfassung zur Seite Nr. 6
Chapter 1 Introduction 1 WAP-4060PE is an IEEE 802.11g Wireless Access Point with PoE. Catering to the enterprise demands, WAP-4060PE enhances security and management features, including multiple SSIDs, VLAN support, WPA support, RADIUS MAC authentication, rogue AP detection, and so on. The LAN port of WAP-4060PE is 802.3af compliant. Therefore, it can be installed anywhere without the constraint on power socket. Provided with one reversed-polarity SMA male connec- tor, WAP-4060PE is ea
Inhaltszusammenfassung zur Seite Nr. 7
n Provide Windows-base utility, Web, and CLI (Command Line Interface) Configuration n SNMP support 1.4 Physical Details Front panel STATUS On - Error condition. Off - Normal operation. Blinking - During start up, and when the Firmware is being upgraded. POWER On - Normal operation. Off - No power LAN On - The LAN (Ethernet) port is active. Off - No active connection on the LAN (Ethernet) port. Flashing - Data is being transmitted or received via the correspond- ing LAN (Ethernet)
Inhaltszusammenfassung zur Seite Nr. 8
3. Continue holding the Reset Button until the Status (Red) LED blinks TWICE. 4. Release the Reset Button. The factory default configuration has now been restored, and the WAP-4060PE is ready for use. Use a standard LAN cable (RJ45 connectors) to connect this port LAN (PoE) to a 10BaseT or 100BaseT hub on your LAN. Power port Connect the supplied power adapter here. 1.5 Specification Standard IEEE 802.11b, 802.11g Signal Type DSSS (Direct Sequence Spread Spectrum) OFDM with BP
Inhaltszusammenfassung zur Seite Nr. 9
Web based configuration Management RADIUS Accounting RADIUS-On feature RADIUS Accounting update CLI Message Log Access Control list file support Configuration file Backup/Restore Statistics support Device discovery program Windows Utility Super G mode Up to 108Mbps Up to 54Mbps (6/9/12/18/24/36/48/54) 802.11g Data Rate 802.11b Up to 11Mbps (1/2/5.5/11) Dimensions (L x W x 150 x 102 x 30mm H) Weight 210g Operating temperature: 0 – 40 degree C Environmental Storage temper
Inhaltszusammenfassung zur Seite Nr. 10
Moreover, the original antenna of WAP-4060PE can be replaced with other external an- tennas to extend the coverage. Please check the specification of the antenna you want to use, and make sure it can be used on WAP-4060PE. 4. WLAN type If WAP-4060PE is installed in an 802.11b and 802.11g mixed WLAN, its performance will reduced significantly. Because every 802.11g OFDM packet needs to be preceded by an RTS-CTS or CTS packet exchange that can be recognized by legacy 802.11b devices. This
Inhaltszusammenfassung zur Seite Nr. 11
Chapter 2 Installation 2 2.1 General Installation Before you proceed with the installation, it is necessary that you have enough informa- tion about the WAP-4060PE. 1. Locate an optimum location for the WAP-4060PE. The best place for your WAP- 4060PE is usually at the center of your wireless network, with line of sight to all of your mobile stations. 2. Assemble the antenna to WAP-4060PE. Try to place them to a position that can best cover your wireless network. The antenna’s position
Inhaltszusammenfassung zur Seite Nr. 12
Chapter 3 Access Point Setup 3 3.1 Overview This chapter describes the setup procedure to make the WAP-4060PE a valid device on your LAN, and to function as an Access Point for your Wireless Stations. The WAP-4060PE can be configured using either the supplied Windows utility or the Web Browser 3.2 Setup using the Windows Utility A simple Windows setup utility is supplied on the CD-ROM. This utility can be used to assign a suitable IP address to the WAP-4060PE. Using this utility is r
Inhaltszusammenfassung zur Seite Nr. 13
IP address The IP address for the WAP-4060PE. MAC Address The hardware or physical address of the WAP-4060PE. The wireless standard or standards used by the WAP-4060PE (e.g. IEEE Standard 802.11b, 802.11g) FW Version The current Firmware version installed in the WAP-4060PE. Any extra information for the WAP-4060PE, entered by the administrator. Description Note: If the desired device is not listed, check that the device is installed and powered on, then update the list by clicking th
Inhaltszusammenfassung zur Seite Nr. 14
These are the default values. The password can and should be changed. Always enter the current user name and password, as set on the Admin Login screen. 4. You will then see the Status screen, which displays the current settings and status. No data input is possible on this screen. 5. From the menu, check the following screens, and configure as necessary for your environment. Details of these screens and settings are described in the following subsections of this chapter. • Access Co
Inhaltszusammenfassung zur Seite Nr. 15
3.4 Access Control This feature allows you to block certain access from unknown or distrusted wireless stations. Click Access Control on the menu to view a screen like the following. Data - Access Control Screen Enable Use this checkbox to Enable or Disable this feature as desired. Warning: Ensure your own PC is in the "Trusted Wireless Sta- tions" list before enabling this feature. Trusted Sta- This table lists any Wireless Stations you have designated as tions "Trusted". If you hav
Inhaltszusammenfassung zur Seite Nr. 16
Data - Trusted Wireless Stations Trusted Wireless Here lists ass Wireless Stations which you have designated as “Trusted”. Stations Other Wireless Here lists all Wireless Stations detected by the WAP-4060PE, which you have not designated as "Trusted". Stations The name assigned to the Trusted Wireless Station. Use this Name when adding or editing a Trusted Station. The MAC (physical) address of the Trusted Wireless Station. Address Use this when adding or editing a Trusted Statio
Inhaltszusammenfassung zur Seite Nr. 17
Add To add a Trusted Station which is not in the "Other Wireless Stations" list, enter the required data and click this button. Clear Clear the Name and Address fields. 3.5 Security Profiles Security Profiles contain the SSID and all the security settings of this WAP-4060PE. • Up to eight (8) Security Profiles can be defined. • Up to four (4) Security Profiles can be enabled at one time, allowing up to 4 differ- ent SSIDs to be used simultaneously. 12
Inhaltszusammenfassung zur Seite Nr. 18
Data - Security Profiles Screen Profile Profile List All available profiles are listed. For each profile, the following data is displayed: • * (star sign) If displayed before the name of the profile, this indicates the profile is currently enabled. If not displayed, the profile is currently disabled. • Profile Name The current profile name is displayed. • [SSID] The current SSID associated with this profile. • Security System The current security system (e.g. WPA-PSK) is
Inhaltszusammenfassung zur Seite Nr. 19
802.11b/g Bridge Select the primary profile for 802.11b and 802.11g Bridge Mode. This setting determines the SSID and security settings Mode used for the Bridge connection to the remote AP. Isolation None If this option is selected, wireless clients using different pro- files (different SSIDs) are not isolated, so they will be able to communicate with each other. Isolate all If this option is selected, wireless clients using different pro- files (different SSIDs) are isolated from each
Inhaltszusammenfassung zur Seite Nr. 20
Data - VLAN Configuation Screen VLAN – Client Traffic Profile Each profile is listed, whether currently enabled or not. You can assign traffic from each profile (SSID) to a different VLAN if de- sired. To assign multiple profiles to the same VLAN, just enter the same VLAN ID for each profile. VLAN ID Enter the desired VLAN ID, as used on your network. IDs must be in the range 1 ~ 4095. These IDs must match the IDs used by other network devices. VLAN – AP Traffic No VLAN Tag Traffi
