Bedienungsanleitung Metra Electronics 95-7331

Inhaltszusammenfassung zur Seite Nr. 1

INSTALLATION INSTRUCTIONS FOR PART 95-7331
APPLICATIONS
KIA Amanti
2007-2009
95-7331
KIT FEATURES
• Double DIN Radio Provision
• Stacked ISO Mount Units Provision
KIT COMPONENTS
A) Radio Housing B) Double DIN Brackets
A
B
TOOLS REQUIRED:
Small Flat Blade Screwdriver/ Panel Removal Tool
• Phillips Screwdriver • Socket set
1-800-221-0932 www.metraonline.com
© COPYRIGHT 2007-2008 METRA ELECTRONICS CORPORATION

Inhaltszusammenfassung zur Seite Nr. 2

95-7331 TABLE OF CONTENTS Dash Disassembly - KIA Amanti 2007-2009.... ........ ....... ........ ........ ....... 1,2 Kit Assembly - Double DIN Radio Provision /Stacked ISO Mount Units Provision . . . . . . . . .3 Final Assembly . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 *Note: Refer also to the instructions included with the aftermarket radio. KNOWLEDGE IS POWER Enhance your installation and fabrication skills by enrolling in the most recognized and

Inhaltszusammenfassung zur Seite Nr. 3

95-7331 DASH DISASSEMBLY KIA AMANTI 2007-2009 1 Disconnect the negative battery ter- A minal to prevent an accidental short circuit. 2 Unclip the top half of the shift knob and remove the “C” clip securing the shifter. Pull up on shifter to remove. (Figure A) Unclip and remove the panel surround- 3 3 1 2 ing the shifter. (Figure B) Unclip and remove top half of center 4 console including the cup holders. (Figure C) B Open center console and remove 5 screw cover in bottom. (Figure D) Remove (2) 1

Inhaltszusammenfassung zur Seite Nr. 4

95-7331 DASH DISASSEMBLY KIA AMANTI 2007-2009 7 Unclip the rear trim panel from the E center console including a/c vents. Unplug and remove the rear trim panel. (Figure E) 8 Remove (1) Phillips screw from each side at the rear of the center console. (Figure E) Unclip the side panels from the front of 9 the center console. It is not necessary to remove these panels. (Figure F) Remove (4) Phillips screws securing 10 center console then lift and slide the center console back out of the way. F Note:

Inhaltszusammenfassung zur Seite Nr. 5

95-7331 KIT ASSEMBLY DOUBLE DIN RADIO PROVISION STACKED ISO MOUNT UNITS PROVISION *Note: Refer also to the instructions included with the aftermarket radio. 1 Snap the switches into the radio hous- A ing in the same location as removed from the factory radio. (Figure A) 2 Snap the Double DIN brackets to the inside edge of the Radio Housing. (Figure B) 3 Slide the Double DIN Radio or stacked ISO Mount units into the bracket/radio housing assembly and secure to the assembly using the screws supp

Inhaltszusammenfassung zur Seite Nr. 6

95-7331 FINAL ASSEMBLY FINAL ASSEMBLY A (A) Strip wire ends back 1/2" B B) Twist ends together C) Solder D) Tape C D 1 Locate the factory wiring harness in the dash. Metra recommends using the proper mating adapter and making connections as shown. (Isolate and individ- ually tape off the ends of any unused wires to prevent electrical short circuit.) 2 Re-connect the negative battery terminal and test the unit for proper operation. 3 Reassemble radio and dash assemblies in reverse order of disas

Inhaltszusammenfassung zur Seite Nr. 7

95-7331 NOTES 5

Inhaltszusammenfassung zur Seite Nr. 8

95-7331 INSTRUCTIONS 1-800-221-0932 www.metraonline.com REV. 09/12/08 © COPYRIGHT 2007-2008 METRA ELECTRONICS CORPORATION INST95-7331