Inhaltszusammenfassung zur Seite Nr. 1
SPLIT TYPE ROOM AIR CONDITIONER
OPERATION MANUAL
HSU-07RS03/R2
HSU-09RS03/R2
HSU-12RS03/R2
HSU-18RS03/R2
HSU-22RS03/R2
H2SM-18HS03/R2
HSU-09HS03/R2(DB)
HSU-12HS03/R2(DB)
HSU-18HS03/R2(DB)
HSU-22HS03/R2(DB)
HSU-12HSB03/R2(DB)
Please read this operation manual before using the air conditioner.
No.
Inhaltszusammenfassung zur Seite Nr. 2
Cautions Disposal of the old air conditioner Safety Instructions and Warnings Before disposing an old air conditioner that Before starting the air conditioner, read the goes out of use, please make sure it's inop- information given in the User's Guide caref- erative and safe. Unplug the air conditioner ully. The User's Guide contains very impor- in order to avoid the risk of child entrapment. tant observations relating to the assembly, operation and maintenance of the air It must be noticed t
Inhaltszusammenfassung zur Seite Nr. 3
Cautions 7. The appliance is not intended for use Do not obstruct or cover the ventilation by young children or infirm persons grille of the air conditoner.Do not put fingers without supervision. or any other things into the inlet/outlet and swing louver. 8. Young children should be supervised to ensure that they do not play with Do not allow children to play with the air the applience. conditioner.In no case should children be allowed to sit on the outdoor unit. 9
Inhaltszusammenfassung zur Seite Nr. 4
Cautions Safety Instruction Please read the following Safety Instructions carefully prior to use. The instructions are classified into two levels, WARNING and CAUTION according to the seriousness of possible risks and damages as follows. Compliance to the instructions are strictly required for safety use. Installation WARNING Please call Sales/Service Shop for the Installation. Do not attempt to install the air conditioner by yourself because improper works may cause electric shock, fire, wa
Inhaltszusammenfassung zur Seite Nr. 5
Cautions WARNING When abnormality such as burnt-small found, Use an exclusive power source with a immediately stop the operation button and circuit breaker contact sales shop. STRICT OFF ENFORCEMENT Connect power supply cord Use the proper voltage Do not use power supply cord to the outlet completely extended or connected in halfway STRICT STRICT PROHIBITION ENFORCEMENT ENFORCEMENT Take care not to damage Do not insert objects into the air Do not use power supply cord the power supply cord. in
Inhaltszusammenfassung zur Seite Nr. 6
Parts and Functions OPERATE COOL DRY HEAT TIMER HEALTH Indoor unit Display board GREEN RED GREEN YELLOW RED GREEN The conversion of pilot light's colors will be displayed as the figure under different operation models Display board Inlet Air filter (inside) Anion generator (inside) Inlet grille Vertical flap (Use remote controller to adjust up and down air flow. Don't adjust it manually) Horizontal louver (adjust left and right air flow) Power plug For multi-split type, the power plug is on the
Inhaltszusammenfassung zur Seite Nr. 7
Parts and Functions 11. LOCK display 12. FAN SPEED display LOW HI MED AUTO 13. TIMER ON display 14. TEMP button Used to select your desired temperature. 15. Operation mode display Operation mode AUTO COOL DRY HEAT FAN Remote controller 16. SINGAL SENDING display 17. POWER/SOFT display 18. Left/right air flow display 19. TEMP display Remote controller: to display the TEMP. setting. 20. TIMER OFF display 21. CLOCK display 31 22. FAN button Used to select fan speed: LOW,MED, HI, AUTO.
Inhaltszusammenfassung zur Seite Nr. 8
Parts and Functions Clock Set When unit is started for the first time and after replacing batteries in remote controller, clock should be adjusted as follows: 1. Press CLOCK button,"AM" or "PM" flashes. 2. Press or to set correct time. Each press will increase or decrease 1 min. If the button is kept depressed, time will change quickly. 3. After time setting is confirmed, press SET, "AM" or "PM" stop flashing, while clock starts working. Remote controller's operation When in use, pu
Inhaltszusammenfassung zur Seite Nr. 9
Operation Health Operation Remote controller 1. Unit start Link with electronic power. Press ON/OFF on the remote controller, unit starts. The liquid crystal will display the working state of last time (Except Timer, Sleep, Power/Soft and Health airflow). Then set up the comfortable working state. 2. Select operation mode Press HEALTH button. For each press, is displayed. The pilot light of healthy process on the display board is on, hence healthy process begins. When indoor fan
Inhaltszusammenfassung zur Seite Nr. 10
Operation Auto Operation 1. Unit start Link with electronic power. Remote controller Press ON/OFF on the remote controller, unit starts. The liquid crystal will display the working state of last time (Except Timer, Sleep, Power/Soft and Health airflow). 2.Select operation mode Press MODE button. For each press, operation mode changes as follows: Remote controller: AUTO COOL DRY FAN HEAT Then Select Auto operation 3.Fan speed selection Press FAN button. For each press, fan speed changes as fo
Inhaltszusammenfassung zur Seite Nr. 11
Operation Cool Operation 1. Unit start Link with electronic power. Remote controller Press ON/OFF on the remote controller, unit starts. The liquid crystal will display the working state of last time (Except Timer, Sleep, Power/Soft and Health airflow). 2.Select operation mode Press MODE button. For each press, operation mode changes as follows: Remote controller: AUTO COOL DRY FAN HEAT Then Select COOL operation 3.Select temp.setting Press TEMP. button Every time the button is pressed, temp
Inhaltszusammenfassung zur Seite Nr. 12
Operation Dry Operation 1. Unit start Link with electronic power. Press ON/OFF on the remote controller, unit starts. Remote controller The liquid crystal will display the working state of last time (Except Timer, Sleep, Power/Soft and Health airflow). 2.Select operation mode Press MODE button. For each press, operation mode changes as follows: Remote controller: AUTO COOL DRY FAN HEAT Then Select DRY operation 3.Select temp.setting Press TEMP. button Every time the button is pressed, temp.s
Inhaltszusammenfassung zur Seite Nr. 13
Operation Fan Operation 1. Unit start Remote controller Link with electronic power. Press ON/OFF on the remote controller, unit starts. The liquid crystal will display the working state of last time (Except Timer, Sleep, Power/Soft and Health airflow). 2.Select operation mode Press MODE button. For each press, operation mode changes as follows: Remote controller: AUTO COOL DRY FAN HEAT Then Select FAN operation 3.Fan speed selection Press FAN button. For each press, fan speed changes as fol
Inhaltszusammenfassung zur Seite Nr. 14
Operation Heat Operation 1. Unit start Remote controller Link with electronic power. Press ON/OFF on the remote controller, unit starts. The liquid crystal will display the working state of last time (Except Timer, Sleep, Power/Soft and Health airflow). 2.Select operation mode Press MODE button. For each press, operation mode changes as follows: Remote controller: AUTO COOL DRY FAN HEAT Then Select HEAT operation 3.Select temp.setting Press TEMP. button Every time the button is pressed, temp
Inhaltszusammenfassung zur Seite Nr. 15
Operation Air Flow Direction Adjustment 1.Status display of air sending direction Vertical flap Horizontal louvers Pos.1 Pos.1 Pos.2 Pos.2 Pos.3 Pos.3 Pos.4 Pos.4 Pos.5 Pos.5 Pos.6 Pos.6 (Auto swing) Pos.7 Pos.8 2.Up and down air flow direction For each press of button, air flow direction on remote controller displays as follows according to different operation modes: COOL/DRY/FAN: Pos.1 Pos.2 Pos.3 Pos.4 Pos.6 remote controller: HEAT: remote controller: Pos.5 Pos.4 Pos.3 Pos.2 Pos.1 Po
Inhaltszusammenfassung zur Seite Nr. 16
Operation Sleep Operation Before going to bed, you can simply press the SLEEP button and unit will operate in SLEEP mode and bring you a sound sleep. SLEEP operation starts SLEEP operation stops Use of SLEEP function Approx.6hrs After the unit starts, set the operation status, then press SLEEP button before which the Rises 1OC 1 hr clock must be adjusted and time being set. Operation Mode Rises 1OC 1 hr 1. In COOL,DRY mode 1 hours after SLEEP mode starts, temp. will Unit stop Temp.setting be
Inhaltszusammenfassung zur Seite Nr. 17
Operation Timer On/Off Operation Set clock correctly before starting TIMER operation. Remote Controller 1. After unit starts, select your desired operation mode Operation mode will be displayed on LCD. 2. Timer mode selection Press TIMER button to change TIMER mode. Every time the button is pressed, display changes as follows: Remote controller: BLANK TIMER ON TIMER OFF TIMER ON-OFF Then select your desired TIMER mode (TIMER ON or TIMER OFF). " "or " "will flash. 3.T
Inhaltszusammenfassung zur Seite Nr. 18
Operation Timer On-Off Operation Set clock correctly before starting TIMER operation. Remote Controller 1. After unit starts, select your desired operation mode Operation mode will be displayed on LCD. 2. Timer mode selection Press TIMER button to change TIMER mode. Every time the button is pressed, display changes as follows: Remote controller: BLANK TIMER ON TIMER OFF TIMER ON-OFF Then select your desired TIMER mode (TIMER ON - OFF). " "will flash. 3.Time setting Press
Inhaltszusammenfassung zur Seite Nr. 19
Operation POWER/SOFT Operation POWER Operation When you need rapid heating or cooling, you can use this function. Selecting of POWER operation Press POWER/SOFT button. Every time the button is pressed,display changes as follows: BLANK POWER SOFT Stop the display at In POWER operation status: In HEAT or COOL mode, fan speed automatically runs in HI mode for 15 min then returns to original status setting. To cancel POWER operation Press POWER/SOFT button twice ,POWER/SOFT disappears. SOFT Operatio
Inhaltszusammenfassung zur Seite Nr. 20
Operation Health airflow Operation 1.Press ON/OFF to starting The liquid crystal will display the working state of last time (Except timer, sleeping, power/soft and health airflow). Setting the comfort work conditions. 2.The setting of health airflow function 1).Press the button of health airflow, appears on the display. The nether inlet and outlet grills of the air conditioner are closed and the airflow is blown horizontally from the above inlet and outlet grills. Avoid the strong airflo
