Inhaltszusammenfassung zur Seite Nr. 1
PRODUCT GUIDE
MODEL 463231711
IMPORTANT: Fill out the product record information below.
Serial Number
See rating label on grill for serial number.
Date Purchased
For support and to register your
grill, please visit us at
www.charbroil.com
If you have questions or need
assistance during assembly,
please call 1-888-430-7870.
Estimated assembly time: 30 minutes
The following are trademarks registered by W.C. Bradley Co. in the U.S. Patent and Trademark Office: Caldera®; Charcoal2Go®; Char-Br
Inhaltszusammenfassung zur Seite Nr. 2
TABLE OF CONTENTS DANGER For Your Safety . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-3 If you smell gas: Use and Care . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-9 Limited Warranty. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10 1. Shut off gas to the appliance. Parts List . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11 2. Extinguish any open flame. 3. Open lid. Parts Di
Inhaltszusammenfassung zur Seite Nr. 3
WARNING CAUTION CALIFORNIA PROPOSITION 65 Using pots larger than 6 quarts in capacity could 1. Combustion by-products produced when using exceed weight limit of the this product contain chemicals known to the State of side burner shelf or side shelf, California to cause cancer, birth defects, and other reproductive harm. resulting in failure 2. This product contains chemicals, including lead of grill cart components. and lead compounds, known to the State of California to cause cancer, birth
Inhaltszusammenfassung zur Seite Nr. 4
LP Cylinder USE AND CARE •The LP cylinder used with your grill must meet the following requirements: •Use LP cylinders only with these required measurements: 12" DANGER (30.5cm) (diameter) x 18" (45.7 cm) (tall) with 20 lb. (9 kg.) capacity maximum. • NEVER store a spare LP cylinder under or near •LP cylinders must be constructed and marked in accordance the appliance or in an enclosed area. with specifications for LP cylinders of the U.S. Department of Transportation (DOT) or for Cana
Inhaltszusammenfassung zur Seite Nr. 5
e s i w k LP Cylinder Exchange Connecting Regulator to the LP Cylinder •Many retailers that sell grills offer you the option of replacing 1.LP cylinder must be properly secured onto grill. (Refer to your empty LP cylinder through an exchange service. Use only assembly section.) those reputable exchange companies that inspect, precision fill, 2.Turn all control knobs to the OFF position. test and certify their cylinders. Exchange your cylinder only for an OPD safety feature-equipped cylinder
Inhaltszusammenfassung zur Seite Nr. 6
Straight Leak Testing Valves, Hose and Regulator 1.Turn all grill control knobs to OFF. 2.Be sure regulator is tightly connected to LP cylinder. 3.Completely open LP cylinder valve by turning hand wheel counterclockwise. If you hear a rushing sound, turn gas off immediately. There is a major leak at the connection. Correct before proceeding. 4.Brush soapy solution onto areas circled below, or other similar Hold coupling nut and regulator fittings on your grill. as shown for proper connection
Inhaltszusammenfassung zur Seite Nr. 7
Safety Tips s Before opening LP cylinder valve, check the coupling nut for WARNING tightness. s When grill is not in use, turn off all control knobs and LP cylinder valve. For Safe Use of Your Grill and to Avoid Serious s Never move grill while in operation or still hot. Injury: s Use long-handled barbecue utensils and oven mitts to avoid • Do not let children operate or play near grill. burns and splatters. s Maximum load for sideburner and side shelf is 10 lbs. • Keep grill area clear an
Inhaltszusammenfassung zur Seite Nr. 8
Ignitor Lighting (continued) Burner Flame Check 8. For grills equipped with ELECTRONIC IGNITION at • Remove cooking grates and flame tamers. Light burners, rotate each burner: knobs from HI to LOW. You should see a smaller flame in Repeat steps 4 through 6 to light each burner. LOW position than seen on HI. Perform burner flame check 9. Once each burner has ignited, turn knobs to desired setting. on sideburner, also. Always check flame prior to each use. If only low flame is seen refer to "S
Inhaltszusammenfassung zur Seite Nr. 9
3. Remove carryover tubes and burners. 4. Detach electrode from burner. CAUTION NOTE: Removal/Detachment method will depend on the burner configuration. See different configurations in SPIDER ALERT! illustrations below. 5. Carefully lift each burner up and away from valve openings. We suggest three ways to clean the burner tubes. Use the one SPIDER AND WEBS INSIDE BURNER TUBE easiest for you. (A) Bend a stiff wire (a light weight coat hanger works well) into a small hook. Run the hook throug
Inhaltszusammenfassung zur Seite Nr. 10
LIMITED WARRANTY This warranty only applies to units purchased from an authorized retailer. Manufacturer warrants to the original consumer-purchaser only that this product shall be free from defects in workmanship and materials after correct assembly and under normal and reasonable home use for the periods indicated below beginning on the date of purchase*. The manufacturer reserves the right to require that defective parts be returned, postage and or freight pre-paid by the consumer for re
Inhaltszusammenfassung zur Seite Nr. 11
PARTS LIST Key Qty Description Key Qty Description A 1 BOTTOM SHELF OO 2 RECTANGULAR BUMPER, F/ TOP LID B 1 TANK SCREW, F/ BOTTOM SHELF PP 1 LOGO PLATE C 2 CASTER, LOCKING QQ 1 HARDWARE F/ TOP LID D 2 CASTER, FIXED RR 1 LEFT DOOR, NO HANDLE E 1 CART LEFT SIDE PANEL SS 3 DOOR AND SB HANDLE F 1 GROMMET, F/ REGULATOR HOLE TT 1 RIGHT DOOR, NO HANDLE G 1 CART RIGHT SIDE PANEL UU 4 FLAME TAMER H 1 CART LOWER BACK PANEL VV 4 COOKING GRATE I 1 FRONT BRACE WW 1 GRIDDLE, F/ SB J 1 HEAT SHIELD, F/ TANK XX
Inhaltszusammenfassung zur Seite Nr. 12
PARTS DIAGRAM QQ BB I H WW G F E CCC C A DDD D B D C 12 FFF LL MM OO OO BBB NN YY PP FF VV ZZ GG UU L SS K XX R O J Q HH II Q P P N M JJ EE CC T DD KK AA X U EEE SS Z Y SS S Z Z Z Z RR TT V W AAA
Inhaltszusammenfassung zur Seite Nr. 13
Front ASSEMBLY Place bottom shelf upside down. Insert Bent U Pin into the caster mounting plate to lock it in place, shown A. 1 Spin the caster clockwise into the threads on the bottom shelf until secure. Remove the Bent U Pin and repeat for remaining casters. Make sure the two locking casters are secured at the rear and the non-locking casters are secured at the front. After all 4 casters are secure remove the Bent U Pin and save for future maintenance. A Fixed caster Bent U pin Locking caster
Inhaltszusammenfassung zur Seite Nr. 14
Place lower back panel between side panels at rear of bottom shelf. Make sure the slots are positioned as shown (A). Secure 3 lower back panel to side panels using four 1/4-20x1/2” screws, 7mm lock washers, and 7mm flat washers on each side. 1/4-20x1/2” screw 7mm lock washer 7mm flat washer Lower back panel A This step requires two people 4 to lift and position grill head onto cart. Carefully lower the grill head onto the cart, aligning slots at bottom of grill head with posts on cart side
Inhaltszusammenfassung zur Seite Nr. 15
On back of grill, place upper back panel between side panels and above lower back panel. 5 Secure upper back panel, in lower holes, using one 1/4-20x1½” screw, 7mm lock washer and 7mm flat washer on each side. Do not fully tighten screws until side shelf installation is complete in later steps. Upper back panel 7mm flat 1/4-20x1½” 7mm lock washer 15
Inhaltszusammenfassung zur Seite Nr. 16
Remove the two 1/4-20x3/4” screws, 7mm lock washers and 7mm flat washers factory attached to the towel bar. 6 Hang the four S hooks on towel bar. Attach towel bar to right side shelf using screws and washers that are removed from towel bar, shown A. Insert flange on right side shelf into side shelf brackets on side of firebox, shown B. Attach rear of shelf using one 1/4-20x3/4” screw, 7mm flat washer, 7mm lock washer and 1/4” nut in upper hole; using one 1/4-20x1½” screw, 7mm lock washer a
Inhaltszusammenfassung zur Seite Nr. 17
Insert tabs on left sideburner shelf assembly into rectangular slots in side of firebox, shown A. 7 Attach rear of shelf using one 1/4-20x3/4” screw, 7mm flat washer,7mm lock washer and 1/4”nut in upper hole; and using 1/4-20x1½” screw, 7mm lock washer, 7mm flat washer in lower hole, shown B/C. Attach front of shelf and fascia using two 1/4-20x3/4” screws, 7mm flat washers, 7mm lock washers and 1/4”nuts, and one #8x3/8” self-tapping screw with large washer, shown C/D/E. Now you may fully tig
Inhaltszusammenfassung zur Seite Nr. 18
Front brace Insert front brace under control panel and between cart side panels. Make sure door hinge pins are on the top side and 8 facing the front. Secure using two 1/4-20x1½” screws, 7mm lock washers, and 7mm flat washers on each side. NOTE: MAKE SURE THAT THE FRONT BRACE IS MOUNTED IN THE MOST DOWNWARD POSITION WHEN ASSEMBLED TO CART. 7mm flat washer 1/4-20x1½” 7mm lock screw washer First, remove the two screws and lock washers factory attached to the sideburner valve bracket. Position si
Inhaltszusammenfassung zur Seite Nr. 19
Insert sideburner burner into left shelf.The stud on bottom of burner fits into rear small hole in sideburner drip pan on 10 8a shelf, shown A. Secure burner to sideburner drip pan with one Wing nut, shown B. Under sideburner shelf, attach sideburner ignitor wire to electrode. Make sure burner tube engages sideburner valve, shown C. B sideburner drip pan A sideburner burner Wing nut C sideburner drip pan electrode ignitor wire Place sideburner lid onto left shelf and align holes in back of lid
Inhaltszusammenfassung zur Seite Nr. 20
. Place sideburner grate and griddle into sidebruner shelf. 12 B Griddle Sideburner grate Inside of cart, insert rear heat shield tabs(without holes) into three slots between upper and lower back panels, shown A. 13 Attach shield tabs self-tapping screws. under front brace with three #8x3/8” Then insert left and right grease tray rails into slots beneath grease tray opening in rear upper panel. Attach rails to brace with two #8x3/8” self-tapping screws, shown B. Some components not shown fo
