Inhaltszusammenfassung zur Seite Nr. 1
ULTRA HIGH EFFICIENCY COMMERCIAL GAS WATER HEATER
(EF Series Models)
WARNING: If the information in
these instructions is not followed
exactly, a fire or explosion may
result causing property damage,
personal injury or death
- Do not store or use gasoline or other
flammable vapors and liquids in the
vicinity of this or any other appliance
- WHAT TO DO IF YOU SMELL GAS
• Do not try to light any appliance.
Inhaltszusammenfassung zur Seite Nr. 2
SECTION I: IMPORTANT INFORMATION READ CAREFULLY This gas-fired water heater is design certified by CSA International under the American National Standard, Z21.10.3 (as indicated on the rating plate) and CAN/CGA 4.3-M (as indicated on the rating plate) available from CSA Standards Association, 178 Rexdale Blvd., Etobicoke, Ontario, Canada M9W 1R3. This water heater must be installed in accordance with local codes. In the absence of local codes, it must be installed in
Inhaltszusammenfassung zur Seite Nr. 3
DANGER DO NOT store or use gasoline or other flammable, combustible, or corrosive vapors and/or liquids in the vicinity of this or any other appliance. DO NOT install any damaged venting system components. If damage is evident then please contact the supplier where the water heater was purchased or the manufacturer listed on the rating plate for replacement parts. Use only vent terminals provided or factory authorized terminals for venting this water heater. This water heater is equ
Inhaltszusammenfassung zur Seite Nr. 4
WARNING This water heater needs fresh air for safe operation and must be installed so there are provisions for adequate combustion and ventilation air. Insufficient air supply will cause a recirculation of combustion products resulting in contamination that may be hazardous to life. This will result in carboning or sooting of the combustion chamber, burners, and flue tubes and creates a risk of asphyxiation. This water heater requires its own separate venting system. DO NOT connect t
Inhaltszusammenfassung zur Seite Nr. 5
SECTION II: SPECIFICATIONS Figure 1. Dimensional Layout Recovery GPH DIMENSIONS ( INCHES ) At Degree Rise 1st Hr. D E F Del. C H Front Space Stg. Flr to Flr to Fl. to Gal. G Gas Relief Shpg. Input Therm. Flr to Inlet T&P Outlet Fl. to Wtr. Heating At Cap. A B Vent Wtr. Valve Wtr. Fl. to Air Gas Conn. Conn. Conn. Valve Wt. Rate 100°F U.S. Eff. 40°F 100°F 140°F Outlet Conn Conn Conn Intake Conn. Dia. Dia. Dia. Open. (LBS) Model No. BTU/h Gal. % Ht. Dia. Rise E
Inhaltszusammenfassung zur Seite Nr. 6
SECTION III: GENERAL INFORMATION FEATURES This water heater contains the following features: MAIN POWER ON/OFF SWITCH – The front panel of this water heater has a lighted ON/OFF switch, which is illuminated when the main power is turned on to indicate power to the water heater. COMBUSTION SYSTEM –This water heater is equipped with a self-compensating negative pressure pre-mix combustion system. As the blower operates, air is drawn in through the air intake and into a venturi
Inhaltszusammenfassung zur Seite Nr. 7
LATCHES – The latches allow easy access for servicing the water heater from the top. Simply remove the two latches for servicing and re-latch upon completion. No tools are required to obtain access to the top of the water heater. TEMPERATURE AND PRESSURE RELIEF VALVE – WARNING Keep clear of the combination temperature and pressure relief valve discharge line outlet. The discharg e may be hot enough to cause scald injury
Inhaltszusammenfassung zur Seite Nr. 8
Figure 2. Condensate Elbow With Loop CLEANOUT – All models are equipped with a cleanout opening to aid in removal of hard water deposits from the tank bottom. If this water heater operates under hard water conditions, the following should be performed at least every 3 months: Turn off water supply and drain the water heater. Remove the cleanout jacket cover and tank cover. When cleaning the tank, care must be taken to avoid trying to break deposits loose as this could damage t
Inhaltszusammenfassung zur Seite Nr. 9
SECTION IV: INSTALLATION INSTRUCTIONS WARNING INSTALLATION OF THIS WATER HEATER REQUIRES ABILITY EQUIVALENT TO THAT OF A LICENSED TRADESMAN IN THE FIELD INVOLVED. PLUMBING, AIR SUPPLY, VENTING, GAS SUPPLY AND ELECTRICAL WORK ARE REQUIRED. DO NOT ATTEMPT TO LIGHT ANY GAS APPLIANCE IF YOU ARE NOT CERTAIN OF THE FOLLOWING: • Liquefied petroleum gases/propane gas and natural gas have an odorant added by the gas supplier that aids in detection of
Inhaltszusammenfassung zur Seite Nr. 10
UNPACKING INSPECT SHIPMENT carefully for any signs of damage. 1. All equipment is carefully manufactured, inspected and packed. 2. Any claims for damage or shortage in shipment must be filed immediately with Bradford White Corporation and noted on the Bill of Lading. 3. Remove all venting components from the combustion assembly compartment by removing the latches. NOTICE The vent terminals and the condensate elbow that is supplied with this water heater are stored at the top in th
Inhaltszusammenfassung zur Seite Nr. 11
REMOVE CRATE 1. Remove all banding and pry off crate sides carefully so as not to damage the water heater. 2. Carefully roll/lift the water heater from the crate base. CAUTION Do not drop water heater. Do not bump water heater jacket against floor. Do not bump exhaust vent pipe against crate or other objects. This will damage the heater and cause it to be inoperable or create nuisance problems. MOVE WATER HEATER TO PERMANENT POSITION by sliding or walking. Place drain pan und
Inhaltszusammenfassung zur Seite Nr. 12
MECHANICAL EXHAUSTING OF ROOM AIR 1. Where an exhaust fan is installed in the same room with this water heater and combustion air is drawn from inside the room, sufficient openings for air must be provided in the walls. UNDERSIZED OPENINGS WILL CAUSE AIR TO BE DRAWN INTO THE ROOM THROUGH THE WATER HEATER’S VENTING SYSTEM, CAUSING POOR COMBUSTION THAT MAY BE HAZARDOUS TO LIFE. SOOTING MAY RESULT IN SERIOUS DAMAGE TO THE WATER HEATER AND RISK OF FIRE OR EXPLOSION WHICH CAN ALSO CREATE A
Inhaltszusammenfassung zur Seite Nr. 13
TYPICAL INSTALLATION ILLUSTRATION CAUTION If building cold water supply has a back-flow preventer, check valve or water meter with check valve provisions for thermal expansion of water in the hot water system must be provided. Figure 4. Typical Front Inlet Connection Figure 5. Typical Front Inlet Connect with Storage Heater 13 INTERNET VERSION FOR REFERENCE ONLY
Inhaltszusammenfassung zur Seite Nr. 14
Figure 6. Typical Two Water Heater Connection Figure 7. Typical Three Water Heater Connection Figure 8. Typical Four Water Heater Connection 14 INTERNET VERSION FOR REFERENCE ONLY
Inhaltszusammenfassung zur Seite Nr. 15
SECTION V: WATER CONNECTIONS WARNING Failure to install and maintain a new, listed temperature and pressure relief valve will release the manufacturer from any claim, which might result from excessive temperature and pressures. Hydrogen gas can be produced in an operating water heater that has not had water drawn from the tank for a long period of time (generally two weeks or more). HYDROGEN GAS IS EXTREMELY FLAMMABLE. To prevent the possibility of injury under these conditions,
Inhaltszusammenfassung zur Seite Nr. 16
SCALDING This water heater can deliver scalding temperature water at any faucet in the system. Be careful whenever using hot water to avoid scalding injury. Certain appliances such as dishwashers and automatic clothes washers may require increased temperature water. By setting the thermostat on this water heater to obtain the increased temperature water required by these appliances, you may create the potential for scald injury. To protect against injury, you should install an ASSE ap
Inhaltszusammenfassung zur Seite Nr. 17
ALTERNATE SPACE HEATING WATER CONNECTIONS DANGER Toxic chemical, such as those used for boiler treatment, shall not be introduced into potable water used for space heating. This water heater shall not be connected to an existing heating system or component(s) previously used with a non- potable water heating appliance. All piping components connected to this water heater for space heating applications must be suitable for use with potable water. WARNING When the system requires
Inhaltszusammenfassung zur Seite Nr. 18
Figure 11. Typical Plumbing Schematic for Zoned Heating SECTION VI: VENTING WARNING The vent system must be properly installed. Failure to properly install the vent system could result in property damage, personal injury, or death. DO NOT install damaged venting system components. If damage is evident then please contact the supplier where the water heater was purchased or the manufacturer listed on the rating plate for replacement parts. Use only the vent terminals provided
Inhaltszusammenfassung zur Seite Nr. 19
NOTICE Before beginning installation of any vent pipe, read the vent pipe manufacturer’s installation instructions. Water heater must be protected from freezing downdrafts during shutdown periods Provide protection of the building materials from degradation by flue gases from the exhaust vent terminal. VENTING The venting instructions must be followed to avoid restricted combustion or recirculation of flue gases. Such conditions cause sooting or risks of fire and asphyxiation.
Inhaltszusammenfassung zur Seite Nr. 20
Vent terminals must terminate at least 3 feet (0.9 m) above any forced air inlet located within 10 feet (3.1 m). This provision does not apply to: 1. The combustion air intake of a direct vent appliance or the circulating air inlet and flue gas discharge of listed outdoor appliances. 2. The exhaust vent terminal must be installed with at least 12 inches (30 cm) clearance from any air opening into a building. 3. The bottom of the exhaust vent and combustion air intake terminals must b
