Inhaltszusammenfassung zur Seite Nr. 1
Owner’s Manual
5.5 Horsepower
2400 PSI
2.2 GPM
PRESSURE WASHER
Model No.
919.672241
Safety Guidelines
Assembly
Operation
Maintenance
Storage
Troubleshooting
Repair Parts
CAUTION: Read the Safety Guidelines
and All Instructions Carefully Before
Operating.
Sold by Sears Canada, Inc. Toronto, Ont. M5B 2B
D28235 Rev. 1 6/16/03
Inhaltszusammenfassung zur Seite Nr. 2
TABLE OF CONTENTS WARRANTY . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2 SPECIFICATION CHART . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3 SAFETY GUIDELINES- DEFINITIONS . . . . . . . . . . . . . . . . . . . . . . . . .3 CONSUMER SAFETY INFORMATION . . . . . . . . . . . . . . . . . . . . . . . . .3 IMPORTANT SAFETY INSTRUCTIONS . . . . . . . . . . . . . . . . . . . . . . .3-7 BOX CONTENTS . . . . . . . . . . . . . . . . . .
Inhaltszusammenfassung zur Seite Nr. 3
SPECIFICATION CHART Model No. 919-672241 Pressure Washer Pressure 2400 PSI Flow Rate 2.2 GPM Cleaning Units (PSI x GPM) 5280 Engine RPM 3600 Rated Horsepower 5.5 Spark Plug Gap .030” (0.76mm) Gasoline Capacity .29 gallons (1.1 liters) Oil .58 quarts ( .55 liters) capacity SAE 30 weight SAFETY GUIDELINES - DEFINITIONS This manual contains information that is important for you to know and understand. This information relates to protecting YOUR SAFETY and PREVENTING EQUIPMENT PROBLEMS. To help you
Inhaltszusammenfassung zur Seite Nr. 4
IMPORTANT SAFETY INSTRUCTIONS Read Operators Manual. Do not operate equipment until you have read operators Manual for Safety, Assembly, Operation, and Maintenance Instructions. READ AND SAVE THESE INSTRUCTIONS HAZARD RISK OF EXPLOSION OR FIRE WHAT CAN HAPPEN HOW TO PREVENT IT Spilled gasoline and it’s vapors can be- Shut off engine and allow it to cool before come ignited from cigarette sparks, adding fuel to the tank. electrical arcing, exhaust gases, and hot Use care in filling tank to
Inhaltszusammenfassung zur Seite Nr. 5
HAZARD RISK OF INJURY OR PROPERTY DAMAGE WHEN TRANSPORTING OR STORING WHAT CAN HAPPEN HOW TO PREVENT IT Fuel or oil can leak or spill and could If pressure washer is equipped with a fuel result in fire or breathing hazard, serious shut-off valve, turn the valve to the off injury or death can result. Fuel or oil leaks position before transporting to avoid fuel will damage carpet, paint or other leaks. If pressure washer is not equipped surfaces in vehicles or trailers. with a fuel shut-off va
Inhaltszusammenfassung zur Seite Nr. 6
HAZARD RISK OF UNSAFE OPERATION WHAT CAN HAPPEN HOW TO PREVENT IT Unsafe operation of your pressure washer Do not use chlorine bleach or any other could lead to serious injury or death to corrosive compound. you or others. Become familiar with the operation and con- trols of the pressure washer. Keep operating area clear of all persons, pets, and obstacles. Do not operate the product when fatigued or under the influence of alcohol or drugs. Stay alert at all times. Never defeat the s
Inhaltszusammenfassung zur Seite Nr. 7
HAZARD RISK OF INJURY FROM SPRAY WHAT CAN HAPPEN HOW TO PREVENT IT Always wear ANSI approved Z87 safety High velocity fluid spray can cause glasses.Wear protective clothing to protect objects to break, propelling particles at against accidental spraying. high speed. Never point wand at, or spray people or Light or unsecured objects can become animals. hazardous projectiles. Always secure trigger lock when wand is not in service to prevent accidental operation. Never permanently secur
Inhaltszusammenfassung zur Seite Nr. 8
ASSEMBLY 1. Place handle assembly onto frame Remove and connect handle to frame. NOTE: Knobs are assembled to inside of frame. Loosen c. Place grooves in accessories 2. Connect wand to gun. Tighten panel assembly onto screws securely. and slide panel assembly into place. Screws 3. Attach high pressure hose to gun. Tighten securely. 5. To Assemble Accessories Panel d. Place screws (removed a. Remove top screws on earlier) into the top holes and handle assembly. secure accessories panel b. Loosen
Inhaltszusammenfassung zur Seite Nr. 9
OPERATION READ THIS OPERATION MANUAL AND SAFETY RULES BEFORE OPERATING YOUR UNIT. Compare the illustrations with your unit to familiarize yourself with the location of various controls and adjustments. Save this manual for future reference. Chemical Hose Choke High Control Spray Pressure Gun Hose Throttle Control Hand Grip Fuel Valve Engine Air Filter Lever Multi- Adjustable Spray Wand High Pressure Pump PRESSURE WASHER Chemical Hose: Feeds cleaning agents into the pump to mix with the High Pres
Inhaltszusammenfassung zur Seite Nr. 10
PRESSURE WASHER TO ADJUST PRESSURE TERMINOLOGY The pressure setting is preset at the factory to achieve optimum pressure PSI: Pounds per Square Inch. The unit and cleaning. If you need to lower the of measure for water pressure. Also pressure, it can be accomplished by used for air pressure, hydraulic these methods. pressure, etc. 1. Back away from the surface to be GPM: Gallons Per Minute. The unit of cleaned. The further away you are, measure for the flow rate of water. the less the pressure
Inhaltszusammenfassung zur Seite Nr. 11
The nozzle at the end of the multi- 2. Place other end of chemical hose with filter on it into container holding adjustable spray wand can be rotated chemical/cleaning solution. NOTE: to change the high pressure spray The chemical/water ratio is 7:1, for pattern from a narrow jet to a 40º fan every 7 gallons of water pumped 1 shape, as shown. Markings have been gallon of chemical/cleaning solution placed on the nozzle to help you will be used. select the spray pattern. 3. Set multi-adjustable no
Inhaltszusammenfassung zur Seite Nr. 12
BEFORE STARTING Filler cap/dipstick Read and understand all Important Safety Instructions in the front of this manual and the following Cautions and Warnings before starting the pressure washer. Never fill fuel tank completely. 3. Verify the filter screen is in water Fill tank to 1/2" below bottom of inlet of pump. NOTE: Cone side filler neck to provide space for faces out. fuel expansion. Wipe any fuel spillage from engine and Filter Screen equipment before starting engine. Never fill fue
Inhaltszusammenfassung zur Seite Nr. 13
8. Turn fuel valve to the ON position, If the engine does 1/4 turn counterclockwise. not start after two 9. Move the choke control lever to pulls, pull the trigger to relieve the the CHOKE ON position and pressure. the throttle control to the FAST 11. If the choke was used to start the position. NOTE: No choke is engine, move the choke lever to needed to start a warm engine. the OFF position. 12. Depress trigger on gun to start Choke water flow. NOTE: Stand on a Control stable surface and grip
Inhaltszusammenfassung zur Seite Nr. 14
CUSTOMER RESPONSIBILITIES TABLE Every 25 Every 50 Every 100 Before hours or hours or hours or each use MAINTENANCE TASK yearly yearly yearly ENGINE X check oil level change oil X check air filter X clean/replace spark plug X PRESSURE WASHER check/clean inlet screen X check high pressure hose X check soap and chemical X hose and filter check gun and wand for leaks X Prepare unit for storage if it is to remain idle for longer prepare for storage than 30 days ENGINE Oil Filler To Check Oil Cap/Dip
Inhaltszusammenfassung zur Seite Nr. 15
To Change Oil Air Cleaner Drain the engine oil when the engine is A dirty air cleaner will restrict air flow to warm. Warm oil drains quickly and the carburetor and cause poor engine completely. performance. Inspect the filter each time the engine is operated. Clean the 1. Turn the fuel valve to the OFF position, 1/4 turn clockwise. filter more frequently if the engine is 2. Place a suitable container next to operated in very dusty areas. the engine to catch the used oil. NOTICE: Operating the e
Inhaltszusammenfassung zur Seite Nr. 16
Clean and Replace Spark Plug 3. Pull trigger on gun handle to relieve any water pressure. Change the spark plug every 100 hours of operation or once each year, 4. Disconnect the wand from the gun. whichever comes first. This will help your engine to start easier and run 5. Remove the nozzle from the end better. of the wand with the 2mm allen wrench provided as shown. .030” (0.76 MM) Wire Gauge 6. Clean the nozzle using the nozzle Resistor cleaner provided or a straightened paper clip. Insert in
Inhaltszusammenfassung zur Seite Nr. 17
STORAGE PUMP ENGINE 1. Drain all water from high pressure IMPORTANT: It is important to prevent hose, coil it, and store it in cradle gum deposits from forming in essential of the pressure washer handle. fuel system parts such as the carburetor, fuel filter, hose or tank 2. Drain all water from spray gun and during storage. Also, experience spray wand by holding spray gun indicates that alcohol-blended fuels in a vertical position with nozzle (called gasohol or using ethanol or end pointing dow
Inhaltszusammenfassung zur Seite Nr. 18
8. Pull engine starter rope slowly 10. Reconnect spark plug wire. several times until antifreeze comes out of high pressure hose *Windshield washer fluid may also connection of pump. be used 9. Remove short hose from water inlet of pump. TROUBLESHOOTING GUIDE PROBLEM CAUSE CORRECTION Engine will not 1. No fuel. 1. Add Fuel. start 2. Pressure builds up after 2. Squeeze gun trigger to two pulls on the recoil relieve pressure. starter or after initial use. 3. Choke lever in the “No 3. Move choke
Inhaltszusammenfassung zur Seite Nr. 19
PROBLEM CAUSE CORRECTION No or low 6. Turn off the engine, then the 6. Air in hose. pressure water source. Disconnect (initial use) the water source from the (continued) pump inlet and turn the water source on to remove all air from the hose. When there is a steady stream of water present, turn water source off. Reconnect water source to pump inlet and turn on water source. Squeeze trigger to remove remaining air. 7. Choke lever in the 7. Move choke to the "No "Choke" position. Choke" positio
Inhaltszusammenfassung zur Seite Nr. 20
PROBLEM CAUSE CORRECTION No or low 1. Have replaced by AWSC. 1. Worn seal or packing. pressure (after 2. Worn or obstructed 2. Have replaced by AWSC. period of nor- valves. mal use.) 3. Worn unloader piston. 3. Have replaced by AWSC. Water leaking 1. Worn or broken o-ring. 1. Check and replace. at gun/wand connection 2. Loose hose connection. 2. Tighten. Water leaking 1. Loose connections. 1. Tighten. at pump 2. Piston packings worn. 2. Have replaced by AWSC. 3. Worn or broken o-rings. 3. Have r
