Inhaltszusammenfassung zur Seite Nr. 1
PROPANE CONSTRUCTION
HEATER
OWNER'S MANUAL
Model: BLP35E
APPAREIL DE CHAUFFAGE AU
PROPANE POUR
LA CONSTRUCTION
MANUEL D’UTILISATION
Modèle : BLP35E
PROPAN-BAUSTELLEN-
HEIZGERÄT
BETRIEBSANLEITUNG
Modell: BLP35E
PROPAANKACHEL
VOOR DE BOUW
GEBRUIKERSHANDLEIDING
Model: BLP35E
Inhaltszusammenfassung zur Seite Nr. 2
Inhaltszusammenfassung zur Seite Nr. 3
PROPANE CONSTRUCTION HEATER OWNER’S MANUAL Model: BLP35E IMPORTANT Read and understand this manual before assembling, starting, or servicing heater. Improper use of heater can cause serious injury. Keep this manual for future reference.
Inhaltszusammenfassung zur Seite Nr. 4
SECTION PAGE CONTENTS Safety Information ......................................................................... 2 Unpacking...................................................................................... 3 Product Identification .................................................................... 4 Theory of Operation ...................................................................... 4 Propane Supply .............................................................................. 5 Ins
Inhaltszusammenfassung zur Seite Nr. 5
SAFETY ! WARNINGS Continued • Not for domestic use (inside living areas). Use heater for space heating only. INFORMATION • Intended for temporary heating of buildings under construction, alteration, or repair. Continued • Install and use heater with care. Follow all local ordinances and codes. • Use only in a well-vented area away from combustible materials. • Provide proper ventilation. If not, excessive levels of carbon monoxide (CO) and carbon dioxide (CO ) will form. Provide two fresh, outsi
Inhaltszusammenfassung zur Seite Nr. 6
Hot Air Outlet Shell PRODUCT (Front) Motor IDENTIFICATION Handle Fan Guard Heater Base Piezo Ignitor Button Power Automatic Cord Control Valve Button Inlet Connector Hose /Regulator Assembly Figure 1 - Model BLP35E The Fuel System: The hose/regulator assembly attaches to the propane gas THEORY OF supply. This provides fuel to the heater. OPERATION The Air System: The motor turns the fan. The fan pushes air into and around the combustion chamber. This air is heated and provides a stream of clea
Inhaltszusammenfassung zur Seite Nr. 7
User must provide propane gas and propane tank(s). PROPANE Use this heater only with a propane vapor withdrawal supply system. The amount SUPPLY of propane gas ready for use from propane tanks varies. Two factors decide this amount: 1. The amount of propane gas in tank(s) 2. The temperature of tank(s) This heater is designed to operate with a minimum 9-kg propane tank. You may need two or more tanks or one larger tank in colder weather. Use a 45-kg tank for longer operation or in very cold weath
Inhaltszusammenfassung zur Seite Nr. 8
3. Connect hose to inlet connector. Tighten firmly using a wrench. INSTALLATION IMPORTANT: Use extra hose or piping if needed. Install extra hose or piping Continued between hose/regulator assembly and propane tank. You must use the regula- tor supplied with heater. Hose Inlet Connector Figure 4 - Hose and Inlet Connector 4. Open propane supply valve on propane tank(s). 5. Check all connections for leaks. Apply mixture of liquid soap and water to gas joints. Bubbles forming show a leak that must
Inhaltszusammenfassung zur Seite Nr. 9
OPERATION ! WARNING Review and understand the warnings in the Safety Informa- tion section, pages 2 and 3. They are needed to safely oper- ate this heater. Follow all local codes when using this heater. To Start Heater 1. Follow all installation, ventilation, and safety information. 2. Locate heater on stable and level surface. Make sure strong drafts do not blow into front or rear of heater. 3. Plug heater power cord into electrical source. Motor will start. Fan will turn, forcing air out front
Inhaltszusammenfassung zur Seite Nr. 10
STORAGE ! CAUTION Disconnect heater from propane supply tank(s). 1. Store propane tank(s) in safe manner. Follow all local codes. Always store propane tanks outdoors. 2. Store in dry, clean, and safe place. Do not store hose/regulator assembly inside heater combustion chamber. 3. When taking heater out of storage, always check inside of heater. Insects and small animals may place foreign objects in heater. Keep inside of heater free from combustible and foreign objects. Remove motor and other in
Inhaltszusammenfassung zur Seite Nr. 11
TROUBLE- ! WARNING SHOOTING Never service heater while it is plugged in, connected to propane supply, operating, or hot. Severe burns and electrical shock can occur. OBSERVED FAULT POSSIBLE CAUSE REMEDY Fan does not turn No electrical power to Check current to electrical out- when heater is heater let. If current is good, check plugged in. heater power cord for breaks. Fan hitting inside of Adjust motor/fan guard to keep heater shell fan from hitting inside of heater shell. Bend fan guard if nec
Inhaltszusammenfassung zur Seite Nr. 12
SERVICE ! WARNING PROCEDURES Never service heater while it is plugged in, connected to propane supply, operating, or hot. Severe burns and Motor and Fan electrical shock can occur. 1. Remove three screws that attach fan guard to heater shell. 2. Remove motor and fan guard from heater shell (see Figure 7). 3. Use pliers to remove the fan nut from front of motor shaft (see Figure 8). 4. Remove fan. Be careful not to damage fan blade pitch. 5. Remove three nuts that attach fan guard to motor using
Inhaltszusammenfassung zur Seite Nr. 13
Ignitor 1. Remove motor and fan guard from heater (see Motor and Fan, page 10, steps 1 and 2). Piezo Ignitor 2. Remove black ignitor wire Bushing from piezo ignitor. Access Ignitor Wire ignitor wire through underside of heater base (see Figure 11). Push wire Underside of up through bushing in Heater Base heater shell. 3. Remove ignitor mounting screw from rear head using Figure 11 - Removing Ignitor Wire from Piezo Ignitor nut-driver or standard screwdriver (see Figure 12). 4. Remove ignitor fro
Inhaltszusammenfassung zur Seite Nr. 14
Thermocouple Thermocouple Nut 1. Make sure unit is unplugged. 2. Remove three screws that attach fan guard to heater shell. 3. Remove motor and fan guard from heater shell (see Figure 14). Be careful Thermocouple not to damage fan. 4. Remove thermocouple nut located inside the combus- Figure 14 - Removing Motor and Figure 15 - Thermocouple Nut Location tion chamber (see Figure Fan Guard from Heater 15). 5. Place unit on its side, and Gas Valve remove the thermocouple wire from the gas valve (see
Inhaltszusammenfassung zur Seite Nr. 15
Thermoswitch 1. Make sure unit is un- plugged. 2. Remove three screws that attach fan guard to heater shell. 3. Remove motor and fan guard from heater shell (see Figure 20). Be careful not to damage fan. 4. Remove two nuts and Figure 20 - Removing Motor and Fan Guard from Heater star washers from thermoswitch (see Figure 21). 5. Disconnect the blue Thermoswitch thermoswitch leads in Star base of heater. Washers 6. Remove the thermoswitch assembly. 7. Insert new thermoswitch wires down through ho
Inhaltszusammenfassung zur Seite Nr. 16
ILLUSTRATED PARTS BREAKDOWN 1 Rubber Washer Fan Nut 2 4 Fan 3 Motor Motor 7 Assembly 5 6 2 10 26 16 19 8 9 8 21 31 11 18 30 45 11 26 20 12 17 22 32 29 21 40 11 42 14 33 13 41 44 34 25 23 15 28 43 35 11 36 37 38 27 39 24 14 102588
Inhaltszusammenfassung zur Seite Nr. 17
This list contains replaceable parts used in your heater. When ordering parts, be sure PARTS LIST to provide the correct model and serial numbers (from the model plate), then the part number and description of the desired part. KEY PART KEY PART NO. NUMBER DESCRIPTION QTY. NO. NUMBER DESCRIPTION QTY. 1 099568-01 Inner Shell (Combustion 23 102445-01 Piezo Ignitor 1 Chamber) 1 24 078978-03 Sleeve Cap 1 2 M11084-26 Hex Tap Screw, 25 099598-04AA Base 1 #10-16 x 3/8" 7 26 100397-01 Lock Washer, #4 4
Inhaltszusammenfassung zur Seite Nr. 18
WARRANTY AND REPAIR SERVICE KEEP THIS WARRANTY LIMITED WARRANTY Van Cranenbroek B.V. warrants this product and any parts thereof, to be free from defects in materials and workmanship for six (6) months from the date of first purchase when operated and maintained in accordance with instructions. This warranty is extended only to the original retail purchaser, when proof of purchase is provided. This warranty covers only the cost of parts required to restore the product to proper operating conditi
Inhaltszusammenfassung zur Seite Nr. 19
APPAREILS DE CHAUFFAGE AU PROPANE POUR LA CONSTRUCTION MANUEL D’UTILISATION Modèle : BLP35E IMPORTANT Veiller à lire et bien comprendre ce manuel avant de monter, de mettre en marche ou d’effectuer l’entretien de cet appareil. Son usage incorrect peut résulter en des blessures graves. Conserver ce manuel pour future référence.
Inhaltszusammenfassung zur Seite Nr. 20
SECTION PAGE TABLE DES Informations concernant la sécurité.......................................... 2 MATIÈRES Déballage .................................................................................. 3 Identification du produit ........................................................... 4 Principe de fonctionnement ...................................................... 4 Alimentation en propane .......................................................... 5 Installation .......................
