Inhaltszusammenfassung zur Seite Nr. 1
Kick & Play
Bouncer
Model Number: B8865
IMPORTANT! KEEP FOR FUTURE REFERENCE.
Please read these instructions before assembly and use of this product.
Adult assembly is required.
Tool required for assembly: Phillips screwdriver (not included).
Requires one LR20 (“D”) alkaline battery (not included) in the soothing unit.
Requires three LR6 (“AA”) alkaline batteries (not included) in the toy bar.
w
w
w.
fi
s
he
r
-p
r
i
c
e
.
c
o
m
Inhaltszusammenfassung zur Seite Nr. 2
Warning WARNING To prevent serious injury or death: • It is dangerous to use this reclined cradle on an elevated surface. •Never use on a soft surface (bed, sofa, cushion) since bouncer can tip over and cause suffocation in soft surfaces. •Never use as a carrier or lift while child is seated. • Always use the restraint system. •Never leave child unattended. •Never use as a car seat. • Not recommended for children who can sit up by themselves (6 months approximately, until 9 kg/20 lb). Consumer I
Inhaltszusammenfassung zur Seite Nr. 3
Parts Toy Bar Removable Teether Rings Seat Back Tube 2 Retainers Pad Footrest with Soothing Unit Right Base Wire Base Tube 3 Left Base Wire 4 #8 x 2 cm ( / ") Screw - 2 Shown Actual Size 3
Inhaltszusammenfassung zur Seite Nr. 4
Battery Installation Soothing Unit •Loosen the screw in the soothing unit battery compartment door with a Phillips screwdriver. Remove the battery compartment door. • Insert one LR20 (“D”) alkaline battery. •Replace the battery compartment door. Tighten the screw with a Phillips screwdriver. Do not over-tighten. Toy Bar •Loosen the screw in the toy bar battery compartment door with a Phillips screwdriver. Remove the battery compartment door. • Insert three LR6 (“AA”) alkaline batteries. •Replace
Inhaltszusammenfassung zur Seite Nr. 5
Battery Safety Information 1.5V x 3 LR6 ("AA") SHOWN ACTUAL SIZE 1.5V _ LR20 ("D") + SHOWN ACTUAL SIZE Batteries may leak fluids that can cause a chemical burn injury or ruin your product. To avoid battery leakage: •Do not mix old and new batteries or batteries of different types: alkaline, standard (carbon-zinc) or rechargeable (nickel-cadmium). • Insert batteries as indicated inside the battery compartment. •Remove batteries during long periods of non-use. Always remove exhausted batteries fro
Inhaltszusammenfassung zur Seite Nr. 6
Assembly IMPORTANT! Before assembly or each use, inspect this product for damaged hardware, loose joints, missing parts or sharp edges. DO NOT use if any parts are missing, damaged or broken. Contact Mattel for replacement parts and instructions if needed. Never substitute parts. CAUTION This package contains small parts in its unassembled state. Adult assembly is required. Right Base Coloured Tabs Wire Base Tube Left Base Wire 1 Base Wire Base Tube •Place the base tube on a flat surface as sho
Inhaltszusammenfassung zur Seite Nr. 7
Assembly Soothing Unit Footrest Buttons Up Flex Base Wires Inward Tabs 2 •Position the footrest so that the soothing unit buttons are upright. •While flexing the base wires toward each other, hook the footrest onto the ends of the base wires. •Push the footrest down completely to the tabs on the base wires. 7
Inhaltszusammenfassung zur Seite Nr. 8
Assembly Seat Back Tube Bends Backward Retainers Base Wire Base Wire 3 •Position the seat back tube so that it bends backward. •Fit the seat back tube completely onto the base wires. Make sure the hole in each end of the seat back tube aligns with the hole in each base wire. •Fit a retainer (rounded side inward) to one end of the seat back tube. • Insert a screw through the outside hole in the seat back tube and into the retainer. •While holding the retainer in place, tighten the screw with a
Inhaltszusammenfassung zur Seite Nr. 9
Assembly Pull Up 4 •Pull up on the seat back tube to be sure it is secure. If you can remove either end of the seat back tube, you have not assembled it correctly. Remove the screws and retainers. Re-read and repeat Assembly steps 3 and 4. 9
Inhaltszusammenfassung zur Seite Nr. 10
Assembly Pad B Footrest Seat Back Tube 5 5 •Unbuckle the restraint belts from the restraint pad. Push the restraint belts back through the slots in the pad . •Fit the pad upper pocket onto the seat back tube . B • Lift the footrest. Fit the pad lower pocket onto the footrest . Lower the footrest. 10
Inhaltszusammenfassung zur Seite Nr. 11
Assembly Restraint Belts 5 6 •Fit both restraint belts back through the pad slots, as shown. 11
Inhaltszusammenfassung zur Seite Nr. 12
Assembly 7 •Fit the ends of the toy bar into the sockets in the footrest. Hint: The square end of the toy bar fits into the square socket and the circular end of the toy bar fits into the circular socket. Assembly is now complete. •The toy bar is removable. Simply lift up to remove. 12
Inhaltszusammenfassung zur Seite Nr. 13
Set-Up & Use WARNING To prevent serious injury or death: • It is dangerous to use this reclined cradle on an elevated surface. •Never use on a soft surface (bed, sofa, cushion) since bouncer can tip over and cause suffocation in soft surfaces. •Never use as a carrier or lift while child is seated. • Always use the restraint system. •Never leave child unattended. •Never use as a car seat. • Not recommended for children who can sit up by themselves (6 months approximately, until 9 kg/20 lb). Restr
Inhaltszusammenfassung zur Seite Nr. 14
Set-Up & Use Anchored End Anchored End B B Free End Free End 2 Tighten Loosen To tighten the belts: •Feed the anchored end of the belt up through the buckle to form a loop . B •Pull the free end of the belt . •Repeat this procedure to tighten the other belt. To loosen the belts: •Feed the free end of the belt up through the buckle to form a loop . Enlarge the loop by pulling on the end of the loop toward the buckle. B •Pull the anchored end of the belt to shorten the free end of the belt . •Repe
Inhaltszusammenfassung zur Seite Nr. 15
Set-Up & Use Mode Switch Volume Switch Mode and Volume Switches Footrest Buttons (Underneath Pad) 4 Sounds and Lights Baby Activated •Slide the mode switch to for baby activated mode. •When baby kicks a footrest button, baby is rewarded with sound effects and chasing lights. After baby kicks the buttons several times in a row, baby enjoys a musical tune and twinkling lights. Parent Activated •Slide the mode switch to for parent activated mode. Baby enjoys 10 minutes of music and a light show. Of
Inhaltszusammenfassung zur Seite Nr. 16
Set-Up & Use Teethers 5 •The teethers are removable from the toy on the toy bar. Simply twist the ends of each teether slightly to remove them from the centre toy. Care The pad is machine washable. Wash the pad separately in cold water on the gentle cycle. Do not use bleach. Line dry only. The frame and toy bar and teethers can be wiped clean using a mild cleaning solution and a damp cloth. Do not immerse the soothing unit or toy bar. To remove the pad: • Lift the footrest and remove the pad low
