Inhaltszusammenfassung zur Seite Nr. 1
DUAL DOWEL JOINTER
120V/60hZ
Model 97427
SET Up AND OpERATINg INSTRUcTIONS
Diagrams within this manual may not be drawn proportionally.
Due to continuing improvements, actual product may differ slightly from the product described herein.
®
Distributed exclusively by harbor Freight Tools .
3491 Mission Oaks Blvd., Camarillo, CA 93011
Visit our website at: http://www.harborfreight.com
Read this material before using this product.
Failure to do so can result in serious injury.
SAVE ThIS MANUAL.
Inhaltszusammenfassung zur Seite Nr. 2
NOTIcE is used to SAVE ThIS MANUAL Notice address practices Keep this manual for the safety not related to personal injury. warnings and precautions, assembly, cAUTION, without operating, inspection, maintenance and cAUTION the safety alert cleaning procedures. Write the product’s symbol, is used to address serial number in the back of the manual near practices not related to the assembly diagram (or month and year of personal injury. purchase if product has no number). Keep thi
Inhaltszusammenfassung zur Seite Nr. 3
outlets will reduce risk of electric before plugging in. Carrying power shock. tools with your finger on the switch or plugging in power tools that have b. Avoid body contact with grounded the switch on invites accidents. surfaces such as pipes, radiators, ranges and refrigerators. There is d. Remove any adjusting key or wrench an increased risk of electric shock if before turning the power tool on. A your body is grounded. wrench or a key left attached to a rotating part of the power
Inhaltszusammenfassung zur Seite Nr. 4
the risk of starting the power tool vibration may cause temporary or accidentally. permanent physical injury, particularly to the hands, arms and shoulders. To d. Store idle power tools out of the reduce the risk of vibration-related reach of children and do not allow injury: persons unfamiliar with the power tool or these instructions to operate 1. Anyone using vibrating tools regularly the power tool. Power tools are or for an extended period should dangerous in the hands of untra
Inhaltszusammenfassung zur Seite Nr. 5
12. Use clamps (not included) or other Specific Safety Rules practical ways to secure and support 1. Maintain labels and nameplates on the workpiece to a stable platform. the tool. These carry important safety Holding the work by hand or against information. If unreadable or missing, your body is unstable and may lead contact Harbor Freight Tools for a to loss of control. replacement. 13. This product is not a toy. Keep it out 2. Always examine the workpiece for of reach of childr
Inhaltszusammenfassung zur Seite Nr. 6
approved safety equipment, such as grounded Tools: Tools with Three those dust masks that are specially prong plugs designed to filter out microscopic particles. (California Health & Safety Code § 25249.5, et seq.) 16. The warnings, precautions, and instructions discussed in this instruction manual cannot cover all possible conditions and situations that may occur. It must be understood by the operator that 3-prong plug and Outlet common sense and caution are 1. Tools marked with “
Inhaltszusammenfassung zur Seite Nr. 7
example, a 14 gauge cord can carry Double Insulated Tools: Tools a higher current than a 16 gauge with Two prong plugs cord. (See Table A.) 3. When using more than one extension cord to make up the total length, make sure each cord contains at least the minimum wire size required. (See Table A.) 4. If you are using one extension cord for more than one tool, add the Outlets for 2-prong plug nameplate amperes and use the sum to determine the required minimum 1. Tools marked “Double In
Inhaltszusammenfassung zur Seite Nr. 8
Note: For additional information regarding SpEcIFIcATIONS the parts listed in the following pages, 120 V~ / 60 Hz refer to the Assembly Diagram near 3.55 No Load Amps / 710 Watts Electrical the end of this manual. Power Plug Type: 2-Prong, Polarized Requirements Power Switch Type: Lockable for continuous run Motor RPM 16,500 Drill Bit Diameter 1/4” (Qty 2) Assembly Maximum Drilling 1-7/16” Depth Width Between To Install The Drill Bits: 1-5/16” (O
Inhaltszusammenfassung zur Seite Nr. 9
2. Loosen the Screw (47), and set the 3. Retighten the Clamping Lever (12). cutting depth by sliding the Depth (See Figure D.) Tab (48) along the Depth Ruler (49). 4. NOTE: The height must correspond (See Figure B.) to half the thickness of the workpiece. 3. Retighten the Knob Screw (47) to Also, the groove of the Guide Plate lock the adjustment in place. (See (8) must always be in the middle of Figure B.) the workpiece. knob ScREW FIgURE D (47) FIgURE B hEIghT DEpTh ADJUSTMENT TAB DEp
Inhaltszusammenfassung zur Seite Nr. 10
3. To turn off the Dowel Jointer, move 5. Push the Motor Base (16) carefully the Power Switch (74) all the way forward as far as possible. backward. (See Figure E.) 6. When finished cutting, move the Motor Base (16) backward, and turn FIgURE E the Dowel Jointer off. To Join The Workpieces: 1. When the holes in the workpieces have been made, the workpieces can be joined together. 2. Place wood glue in both grooves of the workpieces. pOWER SWITch 3. Place a dowel pin in the hole of one (74
Inhaltszusammenfassung zur Seite Nr. 11
TO pREVENT SERIOUS 2. BEFORE EAch USE, check to make INJURY FROM TOOL sure the Bits (17) are firmly secured FAILURE: in place, sharp, and free of cracks or Do not use damaged bends. equipment. If abnormal noise 3. AFTER USE, clean external surfaces or vibration occurs, have the of the tool with a clean, moist cloth problem corrected before and mild detergent. Do not use further use. solvents. Inspection, Maintenance, and 4. WhEN STORINg, keep the tool and cleaning its accessories in
Inhaltszusammenfassung zur Seite Nr. 12
pARTS LIST No Specifications Qty 46 Wood-ruff key 3×10 2 1 cross sunk-head screw M4×6 2 47 Knob Screw 1 2 front plate 1 48 Depth Tab 1 3 angle stop 1 49 Depth ruler 1 4 orientation block 1 50 square nut M5 1 5 washer 4 9 51 spring cap 2 52 spring for fixing pin 2 6 cross panhead screw M4×8 3 53 pin 2 7 hexagon bolt M5×25 1 8 guide plate 1 54 Slide bush 2 9 fixing spring 1 55 finger 1 10 lock clamp 1 56 cross panhead screw M3x6 1 11 hex nut 1 57 steel ball Ø5 1 12 Clamping Lever 1 58 Spring 1 13
Inhaltszusammenfassung zur Seite Nr. 13
ASSEMBLY DIAgRAM SKU 97427 For technical questions, please call 1-800-444-3353. Page 13
Inhaltszusammenfassung zur Seite Nr. 14
LIMITED 1 YEAR / 90 DAY WARRANTY Harbor Freight Tools Co. makes every effort to assure that its products meet high quality and durability standards, and warrants to the original purchaser that for a period of ninety days from date of purchase that the engine/motor, the belts (if so equipped), and the blades (if so equipped) are free of defects in materials and workmanship. Harbor Freight Tools also warrants to the original purchaser, for a period of one year from date of purchase, that all
