Inhaltszusammenfassung zur Seite Nr. 1
TM
Tiger MP
S2460
User’s Manual
Revision 1.03
Copyright © Tyan Computer Corporation, 2001. All rights reserved. No part of this manual may be repro-
duced or translated without prior written consent from Tyan Computer Corp.
All registered and unregistered trademarks and company names contained in this manual are property of
their respective owners including, but not limited to the following.
Tyan, Tiger MP S2460 are trademarks of Tyan Computer Corporation.
AMD, AMD Athlon, AMD-760, AMD-762, and
Inhaltszusammenfassung zur Seite Nr. 2
Table of Contents Before you begin... .................................................................... Page 4 ....................................................................... 5 Chapter 1: Introduction 1.1 Congratulations! .........................................................................................................5 1.2 Tiger MP System Block Diagram ...............................................................................6 1.3 Hardware Specifications .................
Inhaltszusammenfassung zur Seite Nr. 3
3.1 Main Setup ...............................................................................................................33 3.1-A Master and Slave Screens .......................................................................................34 3.2 Advanced Setup .......................................................................................................36 3.2-A Chipset Configuration Screen ..................................................................................38 3.2-B
Inhaltszusammenfassung zur Seite Nr. 4
Before you begin... Check the box contents! The retail motherboard package should contain the following: Tiger MP motherboard 34-pin floppy cable UltraDMA-100/66/33 IDE cable Tiger MP user’s manual Tyan driver CD If any of these items are missing, please contact your vendor/dealer for replacements before continuing with the installation process. http://www.tyan.com 4
Inhaltszusammenfassung zur Seite Nr. 5
Chapter 1: Introduction 1.1 Congratulations! You are now the owner of the world’s first dual AMD processor platform! - CONSUMER EDITION! The Tyan Tiger MP™ is a direct descendent of the Thunder K7, the most critically acclaimed and deco- rated system board in the history of Tyan. Aimed directly at the power-user and enthusiast market, the Tiger MP is a high performance workstation platform designed for development and performance applica- tions that require the power of dual AMD Athlon™ MP p
Inhaltszusammenfassung zur Seite Nr. 6
1.2 Tiger MP System Block Diagram S2K 200/ S2K 200/ AMD Athlon MP AMD Athlon MP 266MHz bus 266MHz bus Processor 0 Processor 1 Socket 462 Socket 462 Dual-channel 200/266MHz 64-bit / DDR SDRAM 33MHz bus PCI bus AMD-762 System Controller AGP 4x bus 184-pin Registered PCI slots DDR DIMMs #1 - 5 AGP slot 64-bit / 33MHz AMD-766 SMBus PCI bus Peripheral Winbond 83782D H/W Bus Controller LPC bus Winbond Floppy Device Hardware Monitoring W83627HF Serial LPT Ports http://www.tyan.com 6
Inhaltszusammenfassung zur Seite Nr. 7
1.3 Hardware Specifications Processor Information Dual PGA462 ZIF sockets Supports dual AMD Athlon MP processors Two onboard VRMs 200MHz and 266MHz system bus support Expansion Slots One AGP slot supports 2x/4x modes Four 64/32-bit 33MHz 5V PCI v2.2 slots Two 32-bit 33MHz 5V PCI v2.2 slots Total of seven usable slots Chipset Information AMD-760 MP chipset AMD-762 System Controller AMD-766 Peripheral Bus Controller Winbond W83627HF Super I/O ASIC Hardware Monitoring Winbond W83782D hardware monit
Inhaltszusammenfassung zur Seite Nr. 8
ATX 12” x 10.3” (304.80mm x 261.62mm) Form Factor One 20-pin power connector (requires 30A on +5V line) Stacked mouse & keyboard ports Stacked two USB ports Stacked one parallel, two serial ports FCC Class B (Declaration of Conformity) Regulatory European Community CE (Declaration of Conformity) 1.4 Software Specifications Windows NT/2000 OS http://www.tyan.com 8
Inhaltszusammenfassung zur Seite Nr. 9
Chapter 2: Board Installation 2.1 Installation Once you’ve checked that everything is inside the box (see p. 4 for details), you will then be ready to install your motherboard. The mounting hole pattern of the motherboard matches the ATX board specifi- cations, so your chassis must be capable of supporting an Extended ATX board (check the motherboard dimensions provided on p. 8). 2.2 How to install our products right.. the first time. Question: what’s the first thing I should do? The first thing
Inhaltszusammenfassung zur Seite Nr. 10
2.4 Quick References for Jumpers In this manual, the term “closed” and “on” are used when referring to jumpers (or jumper pins) that are active; “open” and “off” are used when referring to jumpers (or jumper pins) that are inactive. See Figure 2.0a and Figure 2.0c for examples of “on” and “off” pins and jumpers. Jumpers and pins are connected by slipping the plastic jumper connector over the top of two adjacent jumper pins (indicated by 1-2 or 2-3). The metal rod inside the plastic shell bridges
Inhaltszusammenfassung zur Seite Nr. 11
2.5 Map of Motherboard Jumpers (4) DDR DIMM Mouse port Keyboard port sockets (upper port) (lower port) 1 234 P0FAN 20-pin power connector FAN3 P1FAN CPU0 AMD-760 MP CPU1 AGP Slot J89 1 J52 J53 J15 J90 2 3 J34 BIOS 4 5 Primary IDE 6 Secondary IDE FDD Battery J48 J49 J21 J12 * Indicates an optional feature, may not be available on most Tiger MP models Tiger MP S2460 11 Serial Parallel Serial USB port 2 port port 1 Ports (2) 32-bit 33MHz (4) 64/32-bit PCI slots 33MHz PCI slots FAN1 FAN2 J36
Inhaltszusammenfassung zur Seite Nr. 12
HDD LED VCC GND GND +5VCC SWITCH no connect no connect GND SPEAKER SWITCH VCC GND no connect SWITCH GND KEYLOCK GND 2.6 Setting up Jumpers and Onboard Connectors Pinouts for certain connectors are available on the Tyan website: http://www.tyan.com 2.6-A. Front Panel Connector (J12) SLP PWR RST SW SW SW 25 23 21 19 17 15 13 11 9 7 53 1 26 24 22 20 18 16 14 12 10 8 6 4 2 KEY PWR SPEAKER LK LED Abbreviations Your chassis will usually come with connectors to install onto RST Reset the motherboard,
Inhaltszusammenfassung zur Seite Nr. 13
2.6-C. CPU Front Side Bus Jumpers (J48, J49; J52, J53) (READ NOTE BELOW) With these jumpers, the CPU FSB can be set to either 200 or 266MHz. YOU MUST SET THESE JUMPERS FOR PROPER CPU OPERATION. If your CPU can only run at 200MHz, altering these FSB jumpers will not make the CPU run at 266MHz. NOTE: Tyan takes no reponsibility and will not be held liable for damage related to opera- tion of the CPU using different settings from those of the CPU manufacturer’s specified default settings. You MUST
Inhaltszusammenfassung zur Seite Nr. 14
2.6-E. FAN Headers (P0FAN, P1FAN, FAN1, FAN2, FAN3) These headers allow for extra fans to be installed. P0FAN and P1FAN are reserved for CPU0 and CPU1 (respectively). All other fans are left to the user’s discretion. P0FAN FAN3 P1FAN FAN1 FAN2 FAN Specifications 12 3 Voltage 12V ground +12V speed Amperage 300mA The FAN connector has a 12V, 300mA limitation. Tyan takes no responsibility NOTE: and will not be held liable for damage related to the misuse of any FAN header. 2.6-F. Chassis Intrusion
Inhaltszusammenfassung zur Seite Nr. 15
2.6-G. SMBus Connector* (J89) This is a reserved feature for specific functions not usually required for normal board operation. J59 2.6-H. Reserved Jumper* (J34) (RESERVED) This is a reserved feature* for debugging purposes only. DO NOT ADJUST OR TAMPER WITH THIS! J34 * Indicates an optional feature, may not be available on most Tiger MP models Tiger MP S2460 15
Inhaltszusammenfassung zur Seite Nr. 16
HDD LED VCC GND GND GND SWITCH SWITCH GND GND SWITCH SWITCH VCC GND no connect SWITCH GND 2.6-I. Soft Power Connector The soft power connector is part of jumper block J12 (pins 13 and 15). This board uses the chipset for power management, including turning on and off the system. If the power button function option in the BIOS Power Management menu is set to “On/Off” (which is the default), pressing the power button once after the BIOS has booted up will turn the system on and off. If the power b
Inhaltszusammenfassung zur Seite Nr. 17
2.6-K. Flash Utility You can upgrade the BIOS of this motherboard by using the Flash Utility (see p. 44). Check the Tyan website for more details: http://www.tyan.com BIOS Tiger MP S2460 17
Inhaltszusammenfassung zur Seite Nr. 18
2.7 Mounting the Motherboard into the Chassis Your chassis may include mounting hardware. If mounting hardware was included, you can use the fol- lowing examples to help you in installing your motherboard into the chassis. If your chassis has the studs integrated into the chassis wall, then you would only need to use screws (possibly included with your chassis) to install the motherboard. See the examples (Figure 2.0, shown below) for more details. If the chassis includes mounting hardware wit
Inhaltszusammenfassung zur Seite Nr. 19
2.8 Installing Memory Please keep in mind that although some memory modules may appear to be high-quality, they may con- tain inferior or substandard parts. The type of memory you choose to install should be checked against the memory compatibility list, which is available from Tyan’s website at http://www.tyan.com Here are some details of memory installation for this board: At least one REGISTERED DDR DIMM* must be installed for the system to POST. Supports 128MB, 256MB, 512MB**, & 1024MB** PC1
Inhaltszusammenfassung zur Seite Nr. 20
Lock the DIMM into place by pushing the clips back on either end of the socket onto the Step 3 notches in the ends of the DIMM (see pictures below for details). 1 2 Removing a DIMM Removing a DIMM is just the reverse: pull back the clips from the DIMM (see pictures below), and care- fully pull the module straight out. Place the DIMMs in an anti-static bag as soon as you remove them to avoid static damage. 1 2 http://www.tyan.com 20
