Inhaltszusammenfassung zur Seite Nr. 1
User’s Guide
Compaq TFT5030
Flat Panel Monitor
June 2001
Enhanced for accessibility
Inhaltszusammenfassung zur Seite Nr. 2
© 2001 Compaq Computer Corporation. Compaq and Compaq logo Registered in U. S. Patent and Trademark Office. Microsoft, MS-DOS, Windows, Windows NT are trademarks of Microsoft Corporation in the United States and other countries. All other product names mentioned herein may be trademarks of their respective companies. Compaq shall not be liable for technical or editorial errors or omissions contained herein. The information in this document is provided “as is” without warranty of any ki
Inhaltszusammenfassung zur Seite Nr. 3
Product Features The Compaq TFT5030 Flat Panel Monitor has an active matrix, thin-film transistor (TFT), liquid crystal display (LCD). The monitor features include: ■ 15-inch (38.1-cm) viewable area display ■ 1024 × 768 resolution, plus full-screen support for lower resolutions ■ Wide viewing angle to allow viewing from a sitting or standing position, or when moving side-to-side ■ Tilt and swivel capabilities ■ Removable base for flexible mounting solutions ■ Includes both VGA and
Inhaltszusammenfassung zur Seite Nr. 4
Product Features ■ Compliance with the following regulated specifications: ❏ EPA ENERGY STAR ❏ European Union CE Directives ❏ Swedish MPR II 1990 ❏ Swedish TCO '99 Universal Driver Manager This monitor may require a graphics driver (and/or .INF file) that is compatible with your computer’s graphics adapter. The CD- ROM included with this monitor contains an .INF file (see the section on Information Files). Compaq has also created a Universal Driver Manager (UDM) release that supports
Inhaltszusammenfassung zur Seite Nr. 5
Product Features Information Files This monitor includes a CD-ROM with two information files to be installed onto your computer—an .INF file and an .ICM file. ■ The .INF file defines monitor resources and provides specifications used by most operating systems to install support software for certain hardware devices. The .INF file ensures monitor compatibility and optimization with your computer’s graphics adapter. ■ The .ICM file provides color matching consistency from monitor scree
Inhaltszusammenfassung zur Seite Nr. 6
Product Features Setting Up the Monitor To set up the monitor, ensure that the power is turned off to the monitor, computer system, and other attached devices, then follow these steps: 1. Place the monitor in a convenient, well-ventilated location near your computer. 2. Connect the signal and power cables to the monitor 1. 3. Connect the DC connector of the AC adapter to the DC power cable that extends from the monitor base. 4. Connect the AC cable 3 to the AC receptacle on the AC ada
Inhaltszusammenfassung zur Seite Nr. 7
Product Features Connecting the Monitor Cables CAUTION: When connecting the monitor, be sure to use the AC adapter supplied with the monitor. Failure to use this AC adapter may result in damage to the monitor. WARNING: To reduce the risk of electric shock or damage to your equipment: ■ Do not disable the power cord grounding plug. The grounding plug is an important safety feature. ■ Plug the power cord into a grounded (earthed) electrical outlet that is easily accessible at all
Inhaltszusammenfassung zur Seite Nr. 8
Product Features Note: For security purposes, this monitor has been fitted with a slot for use with a security cable lock that can be purchased separately at most computer stores. Note: After you turn on the monitor, install the Compaq LCD Display Assistant utility included on the CD-ROM. Use the on- screen instructions to adjust the picture quality of your monitor. To install this utility onto your computer, follow the instructions on the "Configuring Your Compaq LCD Monitor" card
Inhaltszusammenfassung zur Seite Nr. 9
Product Features Connecting the Video Signal Cable To connect the VGA analog or DVI-D (Digital Visual Interface- Digital) cable to the corresponding connector on the back of the monitor, you must first remove the monitor base cover. Note: For the digital input to function, the VGA cable must be disconnected from the monitor. If both VGA and DVI-D cables are attached, the monitor will default to the VGA input. WARNING: Before beginning to disassemble the monitor, be sure the monito
Inhaltszusammenfassung zur Seite Nr. 10
Product Features 4. Connect the video cable to the corresponding connector on the back panel of the monitor 1 by threading the cable through the neck on the monitor base to the connector, then connect the other end of the cable 2 to the appropriate video connector on the back panel of the computer. Connecting the Video Cable to the Monitor and Computer 5. Replace the monitor back panel and monitor base cover. 6. Reconnect the power cable and power on the monitor and computer. 8 Comp
Inhaltszusammenfassung zur Seite Nr. 11
Product Features The DVI-D connector on this monitor uses digital video information to provide higher speed for higher display resolution. The results are more precise video displays without manually adjusting screen display quality. Signal Cables Included: ■ VGA (Analog) to VGA Connector (15 pin) ■ DVI-D Cable (Digital only) to DVI Digital Connector Removing the Monitor Base Before you can mount the monitor onto a swing arm or other mounting fixture, you must remove the monitor from t
Inhaltszusammenfassung zur Seite Nr. 12
Product Features 2. Remove the cover plate 1 from the monitor base by placing your fingers in the opening on the bottom of the base and pulling upward, then pulling out to remove the cover. 3. Remove the back panel 1 from the monitor by pushing the bottom tabs upward and pulling out to remove the back panel. 4. Disconnect and remove the signal and power cables from the back of the monitor. 5. Remove the four screws 3 as shown in the following illustration. Removing the Monitor Base
Inhaltszusammenfassung zur Seite Nr. 13
Product Features When the base is removed, four threaded mounting holes are exposed on the monitor panel to be used for mounting purposes. These mounting holes are spaced 75 mm apart and are compliant with the Video Electronics Standards Association (VESA) standard for mounting flat panel displays. To mount the monitor on a swing arm or other mounting fixture, follow the instructions included with the mounting fixture to be used. Operating the Monitor Front Panel Controls Compaq
Inhaltszusammenfassung zur Seite Nr. 14
Product Features Front Panel Controls No. Icon Control Function st Menu button 1. Launches 1 and 1 nd 2 level on-screen menus. 2. Exits menus and on-screen display. 1. Selects and Minus button - 2 adjusts the functions. 2. Activates Auto Adjusts when the OSD menu is inactive. Selects and adjusts + Plus button 3 the functions. Turns the monitor Power switch 4 on and off. 1. Green indicates Power LED 5 monitor is turned on. 2 Amber indicates Sleep mode.
Inhaltszusammenfassung zur Seite Nr. 15
Product Features On-Screen Display Settings The adjustments for screen settings are located in the on-screen display (OSD) and can be viewed in one of six available languages. The following menus show the functions at each level: Main Menu Menu Level 1 Menu Level 2 Menu Level 3 Brightness Adjustment scale Contrast Adjustment scale Auto Adjustment Advanced Menu Exit Advanced Menu Brightness Adjustment scale Contrast Adjustment scale Auto Adjustment Image Control
Inhaltszusammenfassung zur Seite Nr. 16
Product Features Main Menu Menu Level 1 Menu Level 2 Menu Level 3 o Color 9300 K o 6500 K Custom Color Color adjustment Cancel Save and Return Language Deutsch English Espanol Francais Italiano Nederlands Cancel Save and Return Power Saver On/Off Selection Management Power On Recall On/Off Selection Mode Display On/Off Selection Serial No. Displays Serial No. Sleep Timer Set Time and On/Off Times Set Default Input - Analog or Digital Default Video Input Video
Inhaltszusammenfassung zur Seite Nr. 17
Product Features Main Menu Menu Level 1 Menu Level 2 Menu Level 3 OSD Control Horizontal Position Adjustment Scale Vertical Position Adjustment Scale OSD Timeout Adjustment Scale OSD Transparency Adjustment Scale Cancel Save and Return Factory Reset Yes/No Exit Compaq TFT5030 Flat Panel Monitor User’s Guide 15
Inhaltszusammenfassung zur Seite Nr. 18
Product Features How to Adjust Settings 1. Launching the on-screen display Menus: ❏ To display the Basic Menu on the monitor screen: Press the Menu button on the monitor front panel. ❏ To display the Advanced Menu: Press the Menu button on the monitor front panel to display the Basic Menu, use the Minus or Plus buttons to scroll to and highlight the Advance Menu selection, then press the Menu button again. Monitor with On-screen Display Note: After the Advanced Menu has been
Inhaltszusammenfassung zur Seite Nr. 19
Product Features 2. To select an item from the Main Menu, scroll down and highlight an item by pressing the Minus (-) button 2 located on the monitor front panel. To reverse or back up, press the Plus (+) button 3. 3. Highlight your choice and press the Menu button 1 again. 4. Adjust the second-level menu displays using the same procedures as the first level. Note: The second-level menus for Brightness and Contrast displays an adjustment screen. Use the Minus button to decrease a
Inhaltszusammenfassung zur Seite Nr. 20
Product Features ■ Check Video Cable—Indicates the video cable may not be plugged into the computer or the computer may not be turned on. Sleep Timer Mode The Sleep Timer mode is an energy-saving feature that enables you to set a time for the monitor to power on and off at the same time every day. This also extends the life of the backlight bulbs in the monitor. The Sleep Timer has five settings: ■ Set Current Time ■ Set Sleep Time ■ Set On Time ■ Timer: On/Off ■ Sleep Now To s
