Inhaltszusammenfassung zur Seite Nr. 1
User’s Manual
MultiSync X462HB
Inhaltszusammenfassung zur Seite Nr. 2
Index Declaration of conformity ............................................................................................................................. English-1 Important Information ................................................................................................................................... English-2 WARNING, CAUTION ........................................................................................................................ English-2 Declaration ........
Inhaltszusammenfassung zur Seite Nr. 3
Declaration of conformity For USA FCC Information 1. Use the attached specified cables with the MultiSync X462HB (X462HB) color display so as not to interfere with radio and television reception. (1) Please use the supplied power cord or equivalent to ensure FCC compliance. (2) Please use a good quality shielded video signal cable. Use of other cables and adapters may cause interference with radio and television reception. 2. This equipment has been tested and found to comply with the limits for
Inhaltszusammenfassung zur Seite Nr. 4
Important Information WARNING TO PREVENT FIRE OR SHOCK HAZARDS, DO NOT EXPOSE THIS UNIT TO RAIN OR MOISTURE. ALSO, DO NOT USE THIS UNIT’S POLARIZED PLUG WITH AN EXTENSION CORD RECEPTACLE OR OTHER OUTLETS UNLESS THE PRONGS CAN BE FULLY INSERTED. REFRAIN FROM OPENING THE CABINET AS THERE ARE HIGH VOLTAGE COMPONENTS INSIDE. REFER SERVICING TO QUALIFIED SERVICE PERSONNEL. CAUTION CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK, MAKE SURE POWER CORD IS UNPLUGGED FROM WALL SOCKET. TO FULLY DISENGAGE THE
Inhaltszusammenfassung zur Seite Nr. 5
Safety Precautions, Maintenance & Recommended Use FOR OPTIMUM PERFORMANCE, PLEASE NOTE THE Immediately unplug your monitor from the wall outlet and refer FOLLOWING WHEN SETTING UP AND USING servicing to qualified service personnel under the following THE MULTI-FUNCTION MONITOR: conditions: • DO NOT OPEN THE MONITOR. There are no user • When the power supply cord or plug is damaged. serviceable parts inside and opening or removing covers • If liquid has been spilled, or objects have fallen into t
Inhaltszusammenfassung zur Seite Nr. 6
Contents Your new MultiSync monitor box* should contain the following: • LCD monitor • Cable cover 1 • Power cord* • Clamp x 3 • Video Signal Cable • Screw (M4 x 10) x 9 • Wireless Remote Control and AA Batteries • CD-ROM 2 • Setup Manual • Thumbscrew for optional stand x 2* Video Signal Cable (Mini D-SUB 15 pin to Mini D-SUB 15 pin) Screw (M4 x 10) x 9 Thumbscrew for 1 2 Power Cord* optional stand x 2* Cable cover Setup Manual Clamp x 3 CD-ROM Setup Manual Wireless Remote Control and AA Batteri
Inhaltszusammenfassung zur Seite Nr. 7
Installation This device cannot be used or installed without the Tabletop Orientation Stand or other mounting accessory for support. For proper • When using the display in the portrait position, the installation it is strongly recommended to use a trained, monitor should be rotated clockwise so that the left side NEC authorized service person. Failure to follow NEC is moved to the top and the LED indicator light is on the standard mounting procedures could result in damage to the bottom. This wi
Inhaltszusammenfassung zur Seite Nr. 8
3. Ventilation Requirements Attaching Mounting Accessories When mounting in an enclosed space or recessed area, The display is designed for use with the VESA mounting leave adequate room between the monitor and the system. enclosure to allow heat to disperse, as shown below. 1. Attach Mounting Accessories Be careful to avoid tipping monitor when attaching accessories. VESA Mounting Interface Allow adequate ventilation or provide air conditioning around the monitor, so that heat can properly diss
Inhaltszusammenfassung zur Seite Nr. 9
Parts Name and Functions Control Panel POWER button EXIT button Switches the power on/off. See also page 16. Activates the OSD menu when the OSD menu is turned-off. Acts as EXIT button within the OSD to move to previous menu. MUTE button Switches the audio mute ON/OFF. Remote control sensor and Power Indicator Receives the signal from the remote control (when using the INPUT button wireless remote control). See also page 11. Acts as SET button within OSD menu. (Toggle switches Glows green wh
Inhaltszusammenfassung zur Seite Nr. 10
Terminal Panel L R In Out In Out R, Cr/Pr G, Y, VIDEO B, Cb/Pb H V L/R L L (OUT) (OUT) (OUT) (OUT) (OUT) Y Cb/Pb (IN1) (IN2) (IN3) L (OUT) R (OUT) R, Cr/Pr G, Y, VIDEO B, Cb/Pb H V Cr/Pr R R (IN) (IN) (IN) (IN) (IN) (IN2) (IN3) Main Power Switch VIDEO IN connector (BNC and RCA) On/Off switch to turn main power ON/OFF. To input a composite video signal. BNC and RCA connectors are not available at the same time (Use only one input). AC IN connector VIDEO OUT connector (BNC) Connects with the s
Inhaltszusammenfassung zur Seite Nr. 11
Kensington Lock For security and theft prevention. EXTERNAL SPEAKER TERMINAL To output the audio signal from AUDIO 1, 2, 3, DPORT, HDMI and TV jack. Red terminal is plus (+). Black terminal is minus (-). Note: This speaker terminal is for 15W + 15W (8 ohm) speaker. Option board slot Slot for board accessories. Please contact your supplier for detailed information. English-9 English
Inhaltszusammenfassung zur Seite Nr. 12
Wireless Remote Control SOUND button Artificial surround sound. KEYPAD Press buttons to set and change passwords, change channel and set REMOTE ID. ENT button* DISPLAY button Turns on/off the information OSD. See page 18. MENU button Turns on/off the menu mode. AUTO SETUP button Enters auto setup menu. See page 20. EXIT button Returns to previous menu within OSD menu. UP/DOWN button Acts as button to move the highlighted area up or down to select adjustment items within OSD menu. Small
Inhaltszusammenfassung zur Seite Nr. 13
REMOTE ID button Operating Range for the Remote Activates REMOTE ID function. Control MTS button* Point the top of the remote control toward the LCD monitor’s remote sensor during button operation. AUDIO INPUT button Use the remote control within a distance of about 7 m (23 ft.) Selects audio input source [IN1], [IN2], [IN3], [DPORT], from remote control sensor or at a horizontal and vertical 1 1 [HDMI], [TV]* , [OPTION]* . angle of within 30° within a distance of about 3.5 m (10 ft.). butt
Inhaltszusammenfassung zur Seite Nr. 14
Setup NEC recommends the following battery use: 1. Determine the installation location • Place “AA” size batteries matching the (+) and (-) signs CAUTION: Installing your LCD display must be done by a on each battery to the (+) and (-) signs of the battery qualified technician. Contact your dealer for compartment. more information. • Do not mix battery brands. CAUTION: MOVING OR INSTALLING THE LCD MONITOR • Do not combine new and old batteries. This can shorten MUST BE DONE BY TWO OR MORE PEOPLE
Inhaltszusammenfassung zur Seite Nr. 15
5. Attach the cable cover • Use six of the M4 x 10 screws (included) to attach the cable cover. 6. Switch on the power of all the attached external equipment When connected with a computer, switch on the power of the computer first. 7. Operate the attached external equipment Display the signal from the desired input source. 8. Adjust the sound Make volume adjustments when required. 9. Adjust the screen (See pages 20 and 21) Make adjustments of the screen display position when necessary. 10. Adju
Inhaltszusammenfassung zur Seite Nr. 16
Connections NOTE: Do not connect/disconnect cables when turning on the monitor or other external equipment as this may result in a loss of the monitor image. NOTE: Use an audio cable without a built-in resistor. Using an audio cable with a built-in resistor turns down the sound. Before making connections: * First turn off the power of all the attached equipment and make connections. * Refer to the user manual included with each separate piece of equipment. Wiring Diagram DVD player DVD player Se
Inhaltszusammenfassung zur Seite Nr. 17
Connecting a Personal Computer Connecting your computer to your LCD monitor will enable you to display your computer’s screen image. Some video cards with a pixel clock over 162MHz may not display an image correctly. Your LCD monitor displays proper image by adjusting the factory preset timing signal automatically. Scanning frequency Remarks Resolution Horizontal Vertical 640 x 480 31.5kHz 60Hz 800 x 600 37.9kHz 60Hz 1024 x 768 48.4kHz 60Hz 1280 x 768 48kHz
Inhaltszusammenfassung zur Seite Nr. 18
Basic Operation Power ON and OFF Modes The LCD monitor power indicator will turn green while powered on and will turn red or amber while powered off. NOTE: The Main Power Switch must be in the ON position in order to power up the monitor using the remote control or the Power Button on the front of the LCD. OFF Main Power Switch ON Power Button Using the remote control English-16
Inhaltszusammenfassung zur Seite Nr. 19
Power Indicator Picture Aspect DVI, VGA, RGB/HV, DPORT Mode Status Indicator Light 2 Power ON Green* FULL ZOOM NORMAL 1 Power OFF (Eco Standby)* Red 3 Power consumption under 0.5W* HDMI, DVD/HD1, DVD/HD2, SCART, VIDEO1, VIDEO2, S-VIDEO, TV* Power OFF (Standby) Amber FULL WIDE ZOOM NORMAL 3, 4 Power consumption under 1W* * Power Save Amber Blinking 6 3, 5 Aspect ratio Unchanged view* Recommended selection Power consumption under 2W* * 6 of image for picture aspect* Power Standby when Green and A
Inhaltszusammenfassung zur Seite Nr. 20
Information OSD The Information OSD provides information such as: Monitor ID, Input Source, Picture Size, etc. Press the DISPLAY button on the remote to bring up the Information OSD. 6 ID number assigned to current monitor* 7 ID number assigned monitor to be controlled via RS-232C* Input Name Audio input mode Picture aspect Input Signal Information Sub picture information *6: “IR CONTROL” should be set “Primary” or “Secondary”. *7: “IR CONTROL” should be set “Primary”. Picture Mode DVI, V
