Resumen del contenido incluido en la página 1
Server Technology
Solutions for the Data Center Equipment Cabinet
Sentry
Commander
- PT40
Installation and Operations Manual
© 2004 Server Technology, Inc. All rights reserved.
Resumen del contenido incluido en la página 2
Instructions This symbol is intended to alert the user to the presence of important operating and maintenance (servicing) instructions in the literature accompanying the appliance. Dangerous Voltage This symbol is intended to alert the user to the presence of un-insulated dangerous voltage within the product’s enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons. Protective Grounding Terminal This symbol indicates a terminal that must be connect
Resumen del contenido incluido en la página 3
Table of Contents CHAPTER 1: INTRODUCTION 1 Features and Benefits .......................................................................................................................2 Technical Support ............................................................................................................................3 Quick Start Guide.............................................................................................................................3 CHAPTER 2: INSTA
Resumen del contenido incluido en la página 4
Resumen del contenido incluido en la página 5
Chapter 1: Introduction FEATURES AND BENEFITS 2 Communication Access Modes ........................................................................................................2 Power Distribution & Remote Management ....................................................................................2 Pass-Thru Port Access......................................................................................................................2 Load and Environment Measurement ..............
Resumen del contenido incluido en la página 6
Introduction The Server Technology Inc. Sentry family of products provides easy, practical, and secure solutions for power distribution, power management and load-measurement for remote internetworking equipment and branch AC circuits. The Sentry PT40 Commander continues to support the elimination of unnecessary trips to remote locations by allowing remote control of the power on/off status for distant critical equipment, minimizing the impact of locked-up devices on mission-critical netwo
Resumen del contenido incluido en la página 7
Technical Support Server Technology understands that there are often questions when installing and/or using a new product. Free Technical Support is provided from 8:30 AM to 5:00 PM, Monday-Friday, Pacific Time. See Technical Support in Warranty, Product Registration and Support for more information. Server Technology, Inc. 1040 Sandhill Drive Tel: 775.284.2000 Web: www.servertech.com Reno, Nevada 89521 USA Fax: 775.284.2065 Email: support@servertech.com Quick Start Guide The follo
Resumen del contenido incluido en la página 8
Resumen del contenido incluido en la página 9
Chapter 2: Installation STANDARD ACCESSORIES 6 ADDITIONAL REQUIRED ITEMS 6 EQUIPMENT OVERVIEW 6 SAFETY PRECAUTIONS 7 INSTALLING THE POWER INPUT RETENTION BRACKET 7 MOUNTING 7 CONNECTING TO THE POWER SOURCE 8 CONNECTING DEVICES 8 CONNECTING TO THE COMMANDER 8 Serial (RS232) port.................................................................................................................8 Ethernet port...................................................................................
Resumen del contenido incluido en la página 10
Installation Before installing your Commander, refer to the following lists to ensure that you have all the items shipped with the unit as well as all other items required for proper installation. Standard Accessories • Mounting bracket hardware: two mounting brackets and four screws • RJ45 to RJ45 crossover cable • RJ45 to DB9F serial port adapter (for connection to standard DB9M DTE serial port) • Pass-Thru cable/adapter kit o Four RJ12 to RJ12 crossover cables o RJ12 to DB25F adapte
Resumen del contenido incluido en la página 11
Safety Precautions This section contains important safety and regulatory information that should be reviewed before installing and using the Commander. For input and output current ratings, see Power Ratings in Appendix C: Technical Specifications. Only for installation and use in a Destiné à l'installation et l'utilisation Nur für Installation und Gebrauch an Service Access Location in accordance dans le cadre de Service Access Anschlusszugriffspunkten gemäß der with the following inst
Resumen del contenido incluido en la página 12
Connecting to the Power Source The input power cord must first be attached to the unit before connecting the unit to the power source. Each outlet powers up sequentially, with a two-second delay between each outlet, eliminating a potential blown primary fuse or circuit breaker from excessive in-rush current. To attach the power cord to the unit: 1. Plug the female end of the power cord firmly into its connector at the base. 2. Use a screwdriver to tighten the two screws on the retention b
Resumen del contenido incluido en la página 13
Chapter 3: Operations INTERFACES 10 Outlet Naming and Grouping 10 Usernames and Passwords 10 HTML INTERFACE 11 Logging In 11 Outlet Control 12 Individual..............................................................................................................................12 Group....................................................................................................................................12 Environmental Monitoring 12 Input Load .............................
Resumen del contenido incluido en la página 14
Operations Interfaces The Sentry has two interfaces: the HTML interface accessed via the HTTP enabled Ethernet connections and the command line for serial and Telnet connections. Outlet Naming and Grouping For commands requiring an outlet name, you may specify it in one of two ways: a predefined absolute name or a descriptive name assigned by an administrator. Absolute names are specified by a period (.) followed by the tower letter, the infeed letter and outlet number. Example: The abs
Resumen del contenido incluido en la página 15
HTML Interface The HTML interface is constructed of three major components: the System Location bar, the User/Navigation bar and the Control Screen. The System Location bar displays the Sentry’s location and IP address as well as the current Control Screen title. The User/Navigation bar displays the current user and privilege level and provides access to all HTML pages. And the Control Screen is used to display current data and allow changes to outlet states or system configuration.
Resumen del contenido incluido en la página 16
Outlet Control The Outlet Control section offers access to the Individual and Group outlet control pages. From the Individual and Group pages, the user can review and manipulate power control functions for all outlets and groups assigned to the current user. Both pages include the outlets absolute and descriptive names, the Outlet Status reported to the Sentry by the outlet, the current Control State being applied by the Sentry and the outlet load in amperes. Available outlet and group
Resumen del contenido incluido en la página 17
Configuration The Configuration section offers access to all unit configuration options including Network, Telnet/HTTP, Serial Ports, Outlets, Groups, Users, FTP, Proxy/SNTP and SNMP. This section is available to administrative level users only. System The System configuration page is used for reference of system information such as Ethernet NIC Serial Number, Ethernet MAC address and system firmware and hardware revisions as well as assignment and maintenance of the system location an
Resumen del contenido incluido en la página 18
Telnet/SSH The Telnet/SSH configuration page used to enable or disable Telnet and SSH support and configure the port number that the Telnet or SSH server watches. For more information on SSH see page 43 in Chapter 4: Advanced Operations. Enabling or disabling Telnet or SSH support: Select Enabled or Disabled from the appropriate Server drop-down menu and press Apply. Changing the Telnet or SSH server port number: In the appropriate Port field, enter the port number and press Apply. HT
Resumen del contenido incluido en la página 19
Serial Ports The Serial Ports configuration page is used for maintenance of all serial/Pass-Thru ports. NOTE: Pass-Thru connections may only be initiated from the command line interface via a direct serial or Telnet session. Setting the data-rate for all serial/Pass-Thru ports: Select the serial/Pass-Thru port data-rate from the drop-down menu and press Apply. Creating a descriptive Pass-Thru port name: Click on the Edit link in the Action column next to the port to be configured. On t
Resumen del contenido incluido en la página 20
Outlets The Outlets configuration page is used for assignment and/or editing of outlet descriptive names and wakeup states. Editing the outlet descriptive name: Click on the Edit link in the Action column next to the outlet to be configured. On the subsequent Outlet Edit page, enter the descriptive name. Up to 24 alphanumeric and other typeable characters (ASCII 33 to 126 decimal, spaces and colon characters are not allowed) are allowed. Press Apply. Changing the outlet wakeup state:
