Resumen del contenido incluido en la página 1
®
HOME APPLIANCES
8564554
8564554
Installation Instructions
Undercounter Dishwasher
Instrucciones de Instalación
Lavavajillas empotrado
Instructions d'installation
Lave-vaisselle encastré
8564554
Resumen del contenido incluido en la página 2
Installation Instructions. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6 Table of Contents Prepare cabinet opening Dishwasher Safety . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 using existing utility hookups . . . . . . . . . . . . . . . . . . . . . 6 Installation Requirements . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 Prepare cabinet opening Tools and parts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 where there are no e
Resumen del contenido incluido en la página 3
Installation Requirements Location Requirements Do not run drain lines, water lines or electrical wiring Tools and Parts where they can interfere with or contact dishwasher motor or legs. Gather the required tools and parts before starting The location where the dishwasher will be installed must installation. Read and follow the instructions provided with provide clearance between motor and flooring. Motor any tools listed here. should not touch the floor. Do not install dishwasher over carpeted
Resumen del contenido incluido en la página 4
Product dimensions Cutout dimensions 24-7/8" (63.2 cm) 3/4" (1.9 cm) insulation – front vent 24-1/2" (62.2 cm)* may be compressed (not used on 24" (61 cm)** all models) All surfaces must be free from intrusions 33-7/8" (86 cm) min. 24" (61 cm) with wheels min. 34" removed (86.4 cm) min.* 3-1/4" 3-1/4" (8.3 cm) (8.3 cm) 2" 2" (5.1 cm) (5.1 cm) 5-1/2" 3-1/2" (14 cm) 6" *** 21" (53.3 cm) (8.9 cm) 6" *** (15.2 cm) (15.2 cm) 2" SIDE VIEW 9" (5.1 cm) 10" (22.9 cm) (25.4 cm) 2-3/4" 3-1/4" 3-
Resumen del contenido incluido en la página 5
Drain Requirements Electrical Requirements • Use the new drain hose supplied with your dishwasher. Contact a qualified electrician. If this is not long enough, use a new drain hose with a Assure that the electrical installation is adequate and in maximum length of 12 feet (3.7 m) that meets all conformance with all national and local codes and current AHAM/IAPMO test standards, is resistant to ordinances. heat and detergent, and fits the 1" (2.5 cm) drain You must have: connector of the dishwash
Resumen del contenido incluido en la página 6
Installation Instructions Install the drain hose IMPORTANT: Always use a new drain hose even when installing a new replacement dishwasher. WARNING 1. Drill a 1-1/2" (3.8 cm) diameter hole in cabinet wall or floor on the side of the opening closest to the sink. Electrical Shock Hazard Disconnect electrical power at the fuse box or circuit 2. Connect drain hose to waste tee or waste disposer breaker box before installing dishwasher. using one of the following methods: Failure to do so can result
Resumen del contenido incluido en la página 7
Option 2: No waste disposer – with air gap: Option 4: No waste disposer – no air gap: 1. Cut end of drain hose if needed (do not cut ribbed 1. Cut end of drain hose if needed (do not cut ribbed section). section). 2. Attach drain hose to air gap with large spring-type 2. Attach drain hose to waste tee with 1-1/2" to 2" clamp. If the drain hose was cut, use a 1-1/2" to 2" (3.8 to 5 cm) screw-type clamp*. (3.8 to 5 cm) screw-type clamp*. This connection must be before the drain trap and at 3. Use
Resumen del contenido incluido en la página 8
Option 2: Power supply cord method: Install the drain hose NOTE: A mating, three prong, ground-type wall receptacle is required in a cabinet next to the dishwasher opening. IMPORTANT: Always use a new drain hose. 1. Drill a 1-1/2" 1. Drill a 1-1/2" (3.8 cm) optional preferred (3.8 cm) hole in diameter hole in locations locations the cabinet rear cabinet wall or floor on or side. Preferred the side of the opening and optional closest to the sink. locations are 2. Connect drain hose to shown. was
Resumen del contenido incluido en la página 9
Option 2: No waste disposer – with air gap: Option 4: No waste disposer – no air gap: 1. Cut end of drain hose if needed (do not cut ribbed 1. Cut end of drain hose if needed (do not cut ribbed section). section). 2. Attach drain hose to air gap with large spring-type 2. Attach drain hose to waste tee with 1-1/2" to 2" clamp. If the drain hose was cut, use a 1-1/2" to 2" (3.8 to 5 cm) screw-type clamp*. (3.8 to 5 cm) screw-type clamp*. This connection must be before the drain trap and at 3. Use
Resumen del contenido incluido en la página 10
2. Remove two screws attaching access panel and lower 8. Measure height of cabinet opening panel to dishwasher using a 1/4" hex socket, nut driver from underside of countertop to or Phillips screwdriver. floor where dishwasher will be installed (you need the lowest 3. Remove panels and set panels aside on a protective point). Check chart for that height surface. opening. Put wheels in the required 4. Check that grounding clip is attached to the lower position. panel. Number of Minimum Wheel
Resumen del contenido incluido en la página 11
5. Gently set panel aside. Install the door handle (on some models) NOTE: Some models have 4 screws per side. IMPORTANT: Do not scratch the front panel during this procedure. screws 1. Remove the Architect™ Series handle, plastic washers and two screws from handle package. 2. Attach the handle to the factory-supplied full front panel as shown. inner screws door panel do not remove screw. film that is not to be removed 6. Lay the factory-supplied full front panel face down on a protective non-sc
Resumen del contenido incluido en la página 12
Option 2: 6. Measure 9-29/32" (25.2 cm) from top of panel and mark a line on the back of panel. Top vented models with a custom full front panel. NOTE: The handle for the custom panel is not included. IMPORTANT: If the handle is attached from the back of the 9-29/32" (25.2 cm) custom panel, the screw heads must be flush with the panel. If the handle is attached to the front of the custom panel, the screw lengths cannot exceed the panel thickness. For more information on KitchenAid custom mark
Resumen del contenido incluido en la página 13
NOTE: These dimensions are for frameless custom panel 16. Remove the two screws and the custom panel and models with a 4-inch (10.2 cm) console only. drill two – 3/32" pilot holes 1/2" (13 mm) deep, where marked. 1/8" (3.2 mm) 17. Reattach the custom panel, inner panel and handle assembly to the door. custom panel 18. Reinstall the two upper most screws into the inner dimensions panel. Do not tighten completely. This will hold the custom panel assembly in place on the door frame. 1/8" 19. In
Resumen del contenido incluido en la página 14
5. Push bracket into slot on the side of dishwasher, and Choose attachment option bend tab in towards the side of the dishwasher so that it keeps the bracket in place. NOTE: Do not attach the dishwasher, this will be done WARNING later. Excessive Weight Hazard bend tabs Use two or more people to move and install dishwasher. Failure to do so can result in back or other injury. Using two or more people, stand the dishwasher up. Option 1: Countertop attachment Move dishwasher into cabinet opening T
Resumen del contenido incluido en la página 15
4. Repeat for other side of dishwasher. Check door spring tension NOTE: Shims must be securely attached to floor to prevent 1. With another person holding the dishwasher to prevent their movement when the dishwasher is operated. it from tipping, open and close the door a few times. If 5. Place level against top front the door closes or falls open under its own weight, the opening of tub. Check that door tension will need to be adjusted. dishwasher is level from side to 2. To adjust the door s
Resumen del contenido incluido en la página 16
Option 2: Power supply cord method WARNING WARNING Electrical Shock Hazard Electrically ground dishwasher. Electrical Shock Hazard Connect ground wire to green ground connector in Plug into a grounded 3 prong outlet. terminal box. Do not remove ground prong. Do not use an extension cord. Do not use an adapter. Failure to follow these instructions can result in death, fire, or electrical shock. Do not use an extension cord. Failure to follow these instructions can result in death, 4. Form bare
Resumen del contenido incluido en la página 17
Connect to drain Secure dishwasher in cabinet opening 1. To help minimize vibration, route drain WARNING drain hose to avoid contact loop with motor, door springs, water line, cabinet, flooring or the edge of the hole where it passes through the cabinet. 2. Do not remove drain loop from side of dishwasher. Tip Over Hazard 3. Place pan under end of drain hose. Pan will collect any Do not use dishwasher until completely installed. water in drain hose. 4. Remove plug and paper from drain connector
Resumen del contenido incluido en la página 18
3. Hold the two panels together and place them against Bottom sound pad installation (on some models) dishwasher leg. 4. Reinstall the screws through the holes in the access 1. Remove the bottom sound pad from inside the panel and the slots in the lower panel. Install right side dishwasher and take it out of the plastic bag. screw first. 2. Place pad on the floor in front of the dishwasher, making sure lettering is facing up and vinyl pad faces down. 3. Fold up and hold the side panels down. C
Resumen del contenido incluido en la página 19
Check operation 1. Read the Use and Care Guide that came with your dishwasher. 2. Check that all parts have been installed and no steps were skipped. 3. Check that you have all the tools you used. 4. Start dishwasher and allow it to complete the shortest wash cycle. After the first two minutes, unlatch door, wait five seconds, then open door. 5. Check to see that there is water in the bottom of the dishwasher tub. Check that dishwasher is working properly. If not, see “If dishwasher does not o
Resumen del contenido incluido en la página 20
® 8564554 Printed in U.S.A. HOME APPLIANCES © 2004 08/2004
