Resumen del contenido incluido en la página 1
CENTURY®
L E G E N D A R Y L E A D E R S H I P
OWNER'S MANUAL
211 / 212
INSTALLATION, OPERATION, MAINTENANCE & PARTS
NOTE: MANUAL including SPECIFICATIONS, subject to change without notice
All ratings specified are based on structural factors only,
not vehicle capacities or capabilities.
CENTURY®
A Division of Miller Industries Towing Equipment Inc.
8503 Hilltop Drive
Ooltewah, Tennessee 37363 FORM NO. 0500659
11 / 97
Phone (423) 238-4171 • FAX (423) 238-5371 PRICE $25.00
Resumen del contenido incluido en la página 2
LIMITED WARRANTY MILLER INDUSTRIES TOWING EQUIPMENT INC., hereinafter referred to as MILLER, warrants to the original purchaser that each new MILLER wrecker or other MILLER products will be free from defects in material and workmanship for a period of twelve (12) months from date placed in service, but in no event shall such warranty period exceed twenty-four (24) months from date of manufacture by MILLER. The purchaser must promptly notify MILLER in writing of any failure in material or workman
Resumen del contenido incluido en la página 3
Section VI - PARTS This Section is provided by the manufacturer for the purpose of ordering any component part of the CENTURY 211 or 212 WRECKER that may be required when part replacement is necessary. Be certain to use only original equipment replacement parts for warranty purposes as well as for keeping your CENTURY 211 or 212 WRECKER in its original state and optimum operating capacities. When ordering replacement or spare parts be sure to provide the following information to the manufacturer
Resumen del contenido incluido en la página 4
Section VI - PARTS (cont'd) BODY ASSEMBLY - 86" WIDE VI-2
Resumen del contenido incluido en la página 5
Section VI - PARTS (cont'd) BODY ASSEMBLY - 86" WIDE REF. NO. PART NO. REQ'D NUMBER DESCRIPTION 1 1 0802629 BODY WELDMENT, 60 C.A. 2 1 0801258 TOOLBOX, 32" 3 1 0302855 LATCH, TOOL COMPARTMENT, PLAIN 4 16 0400567 RIVET, 1/8" X 1/4" POP 5 2 0704516 GUARD, CONTROL STATION 6 4 0400370 CLIP, 1/4" "U" TINNERMAN 7 4 0400066 SCREW, 1/4"-20 X 3/4" HEX HD CAP GR5 ZP 8 4 0400452 LOCKWASHER, 1/4" HELICAL 9 2 0302173 MUD FLAP 10 2 0705092 BAR, MUD FLAP 11 1 0708809 MUD FLAP MOUNTING ANGLE, RIGHT 12 1 0708810
Resumen del contenido incluido en la página 6
Section VI - PARTS (cont'd) BODY ASSEMBLY - 80" WIDE VI-4
Resumen del contenido incluido en la página 7
Section VI - PARTS (cont'd) BODY ASSEMBLY - 80" WIDE REF. NO. PART NO. REQ'D NUMBER DESCRIPTION 1 1 0802637 BODY WELDMENT, 60 C.A. NARROW 2 2 0704516 GUARD, CONTROL STATION 3 4 0400370 CLIP, 1/4" "U" TINNERMAN 4 4 0400066 SCREW, 1/4"-20 X 3/4" HEX HD CAP GR5 ZP 5 4 0400452 LOCKWASHER, 1/4" HELICAL 6 2 0302173 MUD FLAP 7 2 0705092 BAR, MUD FLAP 8 1 0708809 MUD FLAP MOUNTING ANGLE, RIGHT 9 1 0708810 MUD FLAP MOUNTING ANGLE, LEFT 10 2 0802712 STORAGE BRACKET WELDMENT 11 2 0707510 STORAGE BRACKET 12
Resumen del contenido incluido en la página 8
Section VI - PARTS (cont'd) BOOM & UNDERLIFT ASSEMBLY - 211 (Continued on Page VI-8) VI-6
Resumen del contenido incluido en la página 9
Section VI - PARTS (cont'd) BOOM & UNDERLIFT ASSEMBLY - 211 (Continued on Page VI-9) REF. NO. PART NO. REQ'D NUMBER DESCRIPTION 1 1 0802537 MAIN BOOM WELDMENT 2 1 0802510 OUTER BOOM WELDMENT-UNDERLIFT 3 2 03000B-28 TRUNION PIVOT WELDMENT 4 8 0400249 SCREW, 5/8"-11 X 1-1/4" SKT HD CAP 5 8 0400508 WASHER, 5/8" HELICAL LOCK 6 1 0708519 PLATE, COVER-BOOM UPPER 7 1 0708407 SHAFT, LOWER-TILT CYLINDER 8 1 0708408 SHAFT, UPPER-TILT CYLINDER 9 1 0708409 SHAFT, PIVOT BOOM 10 1 0802480 INNER BOOM WELDMENT
Resumen del contenido incluido en la página 10
Section VI - PARTS (cont'd) BOOM & UNDERLIFT ASSEMBLY - 211 (Continued from Page VI-6) VI-8
Resumen del contenido incluido en la página 11
Section VI - PARTS (cont'd) BOOM & UNDERLIFT ASSEMBLY - 211 (Continued from Page VI-7) REF. NO. PART NO. REQ'D NUMBER DESCRIPTION 29 1 0800735 GUIDE, CABLE 30 1 0301531 "U" BOLT (FROM 3/8" CABLE CLAMP) 31 2 0400393 NUT, 3/8"-16 HEX JAM 32 4 0400392 NUT, 3/8"-16 HEX NYLOK 33 2 0700166 WASHER, SPACER 34 12 0300113 GREASE FITTING, ALEMITE 35 1 0703345 SHAFT, EXTEND CYLINDER 36 4 AWS-3022-A SNAP RING 37 2 0701956 SCREW, OUTER CROSS TUBE RET. 38 2 0703640 WASHER, THRUST 39 4 0400452 LOCKWASHER, 1/4"
Resumen del contenido incluido en la página 12
Section VI - PARTS (cont'd) CONTROL & CROSSROD ASSEMBLY - 211 VI-10
Resumen del contenido incluido en la página 13
Section VI - PARTS (cont'd) CONTROL & CROSSROD ASSEMBLY - 211 REF. NO. PART NO. REQ'D NUMBER DESCRIPTION 1 4 0400527 CLEVIS PIN, 5/16" DIA COTTERLESS SS 2 4 0400541 COTTER PIN, 1/16" X 3/4" 3 4 0704529 CROSSROD - WRECKER (86" WIDE BODY) 4 4 0708898 CROSSROD - WRECKER (80" WIDE BODY) 5 1 0703501 ANGLE, CROSSROD BEARING 6 21 0300122 GROMMET, SPLIT PLASTIC 7 8 0400539 COTTER, PIN, 3/16" X 1-1/2" 8 2 0300835 KNOB, WRECKER BOOM "UP/DN" (BLACK) 9 2 0300834 KNOB, CABLE "IN/OUT" (RED) 10 2 0302917 KNOB,
Resumen del contenido incluido en la página 14
Section VI - PARTS (cont'd) WINCH HYDRAULICS - 211 REF. NO. PART NO. REQ'D NUMBER DESCRIPTION 1 2 0300044 CONNECTOR, 1/2" SAE "O" RING X 1/2" X JIC 2 1 0300090 MOTOR, CHAR-LYNN HYDRAULIC 3 2 0300229 ELBOW, 8MJ-8MP90 4 2 0301893 HOSE, WINCH MOTOR 5 REF. 0302936 WINCH ASSEMBLY, RAMSEY 6 3 0400140 SCREW, 3/8"-16 X 4" HEX HD CAP GR5 ZP 7 2 0400196 SCREW, 1/2"-13 X 1-1/4" SKT HD CAP 8 3 0400392 NUT, 3/8"-16 NYLOK HEX ZP 9 2 0400491 LOCKWASHER, 1/2" HELICAL ZP 10 1 0302960 VALVE, 4 SPOOL VI-12
Resumen del contenido incluido en la página 15
Section VI - PARTS (cont'd) BOOM ELEVATION HYDRAULICS - 211 REF. NO. PART NO. REQ'D NUMBER DESCRIPTION 1 2 0300044 O-RING CONNECTOR 2 1 0300206 BRANCH TEE 3 1 0301425 CONNECTOR, MALE 4 4 0301620 O-RING ELBOW, 90° 5 1 0301855 MALE TEE 6 1 0302476 HOLDING VALVE 7 1 0302573 TEE, 6MJ-6MJ-6FJX 8 2 0302909 HOSE ASSEMBLY, 36" 9 4 0302926 HOSE ASSEMBLY, 29" 10 2 0400078 SCREW, 1/4"-20 X 2" HEX HD CAP GR5 ZP 11 2 0400367 NUT, 1/4"-20 HEX NYLOK 12 4 0400451 WASHER, 1/4" FLAT 13 1 0302960 VALVE, 4 SPOOL CO
Resumen del contenido incluido en la página 16
Section VI - PARTS (cont'd) UNDERLIFT HYDRAULICS - 211 REF. NO. PART NO. REQ'D NUMBER DESCRIPTION 1 3 0300044 O-RING CONNECTOR 2 1 0300052 O-RING ELBOW, 90° 3 4 0301522 O-RING CONNECTOR 4 3 031696 ELBOW, 90° 5 REF. 0301825 EXTEND CYLINDER 6 2 0301921 HOSE ASSEMBLY, 128" 7 REF. 0302919 FOLD CYLINDER 8 2 0302922 HOSE ASSEMBLY, 170" 9 REF. 0302960 VALVE, 4 SPOOL CONTROL 10 3 0400140 SCREW, 3/8"-16 X 4" HEX HD CAP GR5 ZP 11 3 0400392 NUT, 3/8"-16 HEX NYLOK VI-14
Resumen del contenido incluido en la página 17
Section VI - PARTS (cont'd) PUMP & RESERVOIR HYDRAULICS - 211 REF. NO. PART NO. REQ'D NUMBER DESCRIPTION 1 1 0300052 O-RING ELBOW, 90° 2 2 0300055 BARB, 3/4" HOSE X 3/4" NPT 3 1 0300056 BARB, 1" NPT 4 33" 0300057 HOSE, 3/4" RETURN 5 9 FT. 0300058 HOSE, 1" SUCTION 6 4 0300071 CLAMP, 1" HOSE 7 1 0300136 RETURN LINE FILTER 8 1 0300165 HOSE ASSEMBLY, FJX 9 1 0300188 CLAMP, 1" INSULATED HOSE 10 1 0300692 ELBOW, 1" 90° STREET 11 1 0301375 O-RING ELBOW, 90° 12 1 0301767 HOSE BARB, 1" HOSE X JIC 13 1 03
Resumen del contenido incluido en la página 18
Section VI - PARTS (cont'd) BOOM & UNDERLIFT ASSEMBLY - 212 (Continued on Page VI-18) VI-16
Resumen del contenido incluido en la página 19
Section VI - PARTS (cont'd) BOOM & UNDERLIFT ASSEMBLY - 212 (Continued on Page VI-19) REF. NO. PART NO. REQ'D NUMBER DESCRIPTION 1 1 0802552 MAIN BOOM WELDMENT 2 1 0802510 OUTER BOOM WELDMENT-UNDERLIFT 3 2 3000B-28 TRUNION PIVOT WELDMENT 4 8 0400249 SCREW, 5/8"-11 X 1-1/4" SKT HD CAP 5 8 0400508 WASHER, 5/8" HELICAL LOCK 6 1 0708519 PLATE, COVER-BOOM UPPER 7 1 0708407 SHAFT, LOWER-TILT CYLINDER 8 1 0708408 SHAFT, UPPER-TILT CYLINDER 9 1 0708409 SHAFT, PIVOT BOOM 10 1 0802480 INNER BOOM WELDMENT
Resumen del contenido incluido en la página 20
Section VI - PARTS (cont'd) BOOM & UNDERLIFT ASSEMBLY - 212 (Continued from Page VI-16) VI-18
