Resumen del contenido incluido en la página 1
Bluetooth Handsfree
Bluetooth Handsfree
Car Kit with LCD
Car Kit with LCD
USER’S MANUAL
Model: BT380
Resumen del contenido incluido en la página 2
Contents Identifying Components······················································ 1 Installing the Junction Box·················································· 3 Connecting the Power Supply ··········································· 4 Connecting Accessories ····················································· 5 Preparing the Remote Control············································ 6 Installing the battery ····································································
Resumen del contenido incluido en la página 3
Notes on Safety 1. Unit installation – Installing the BT380 Handsfree Car Kit requires specialized knowledge and skills. Incorrect installation may cause damage to your BT380 unit and/ or your vehicle!! Therefore, it is strongly advised that the system be installed by a qualified professional. 2. Installation location – Unsuitable installation locations may lead to incorrect functioning of the essential vehicle safety equipments such as air bag or it may become a source of injury in
Resumen del contenido incluido en la página 4
Resumen del contenido incluido en la página 5
1. Introduction Carefully unpack the BT380 Bluetooth Handsfree Car Kit and check that the following items are included: Identifying Components Unpack the Car Kit package and ensure the following items are included. Remote / Bracket / Clasp / BT-380 LCD Junction Box Part # 31122450 Part # 31122100 CR2032 Battery Part # 31122000 Stand Speaker Microphone Part # 31122060 Part # 31092430 Part # 31092440 Power Cable Fuse Set Part # 31102160 Part
Resumen del contenido incluido en la página 6
Resumen del contenido incluido en la página 7
2. Installation This section demonstrates how to set up and install the BT380 into a vehicle. Installing the Junction Box The Car Kit is designed to work with the 12/24-volt power supply of the vehicle. Refer to the following to install the junction box in a vehicle. 1. Locate a suitable place inside the car to mount the junction box. Select a dry place that avoids excessive heat and mechanical vibration. Ideally, the junction box should be hidden from view, but still easily accessible
Resumen del contenido incluido en la página 8
2. Installation Connecting the Power Supply (For Options 1 and 2 only) The following illustration demonstrates how to connect the Car Kit’s power cables to the vehicle’s electrical system. Important: The blue cable must be connected to the 12/24V switched to enable the Car Kit to go into standby mode. Do not connect the blue cable to the +12/24V permanent. Doing so may discharge the battery of the vehicle and prevent the Car Kit from being reset. 4
Resumen del contenido incluido en la página 9
2. Installation Connecting Accessories The following illustration shows where to connect accessory devices. Item Description The caller ID should be placed on the dash within view of the driver and passenger. Caller ID (See Installing the Caller ID Display on page 9.) Ideally, the microphone should be located in Microphone front of the user and above waist height. For best reception, the speaker should be Speaker mounted at least 80cm (30 inches) from the Car Kit’s microphone
Resumen del contenido incluido en la página 10
2. Installation Preparing the Remote Control The remote control is designed to attach to the inside of the steering wheel on the left or right side. Installing the battery Before attaching the Remote control , install the supplied battery. 1. Remove the battery cover from the rear of the control module and remove the old battery (if any). 2. Insert the new battery with the correct polarity as shown below. 3. Put the battery cover back on. 6
Resumen del contenido incluido en la página 11
2. Installation Attaching the remote control Refer to the following to attach the remote control: 1. Attach the rubber clasp to the two notches on one side of the bracket base. 2. Pull tightly on the rubber clasp and position the bracket base on the inside of the steering wheel. 3. Wrap the rubber clasp tightly around the steering wheel and secure it on the other two notches on the bracket base. 7
Resumen del contenido incluido en la página 12
2. Installation 4. Cut off the excess rubber as close to the bracket base as you can. 5. Attach the bracket cover with the two supplied hex bolts. 6. Slide the remote control into the control bracket as shown. To remove the remote control, push the release button to the right and remove the remote control. 7. Now the remote is stabled and attached to the wheel. 8
Resumen del contenido incluido en la página 13
2. Installation Installing the Caller ID Display The caller ID is designed to sit on the dashboard once it is attached to the stand. Remove the adhesive cover from the sticker pad (attached) from the base and press firmly to secure in place. If you wish to attach the LCD display elsewhere, such as next to the car radio, detach the base from the stand by removing the screw as demonstrated. Turn the stand inwards and apply a sticker pad (provided) to the back of the stand. Position
Resumen del contenido incluido en la página 14
2. Installation Installing the Microphone Before installing the microphone, take note of the following: Make sure that the cable can reach from the microphone to the junction box. If the cable is too short, relocate the microphone. Do not lengthen the cable. The supplied microphone is uni-directional. For best results, place the microphone in front of the person talking. We recommend on the A-Pillar. It has a reception angle of 60 degrees, and is most effective within a 60-cm radius.
Resumen del contenido incluido en la página 15
3. Operation How to Operate the Car Kit Basic operation Connecting to the Mobile Phone for the First Time As soon as the ignition is turned on “BT380” text will be displayed on the backlit screen and it will quickly enter the “Pairing” mode searching for available Bluetooth mobile phones for pairing up. If the pairing screen does not display automatically, you will need to turn on this function manually. See Connection Settings on page 17. Pairing BT380 You will need to
Resumen del contenido incluido en la página 16
3. Operation Please select this item to pair and enter 1234 when prompted by the password request. This will allow BT380’s device name to reside in the mobile phone memory, listed along with other previously paired devices in the handset. You then need to press the connect command on the phone to establish the connection with BT380 and your mobile phone name should appear on the main idle screen. You will also get battery and signal indications if your phone supports these functions.
Resumen del contenido incluido en la página 17
3. Operation Nokia 6230i), it will upload call history, phone book entries, and also sort the phone book as soon as the phone is connected with the car kit. Note: Phonebook synchronization and sorting time may differ depending on size of phonebook list. This may affect the initial remote control response at start up. In the event that you do not wish to upload automatically, you can disable this function and upload the phonebook manually. To setup manual phonebook upload, please follow t
Resumen del contenido incluido en la página 18
3. Operation As soon as you select Receive Contact the BT380 temporarily disconnects from your mobile phone to allow for the contact entry to be included into the BT380’s memory. Select the entry required and go to the send option to select send via Bluetooth. You can send multiple entries by repeating the process. Once you have finished, push the Reject/End button to stop the receiving contacts process and re-establish the Bluetooth link with the last connected mobile phone. Note: Some
Resumen del contenido incluido en la página 19
3. Operation have selected the telephone number, press the Answer button to call the telephone number you have just entered. 1 2 3 4 5 6 7 8 Dial Number 0286655757 Settings Voice Tag Activation User can use phone’s voice command function via the BT380: Press the Reject/End button on remote control for more than 3 seconds and when you hear the voice activation sound speak the name to the microphone and wait for phone to dial. Please note for some phones users are required to pre-re
Resumen del contenido incluido en la página 20
3. Operation Settings → Bluetooth Setup → Paired Devices Note: To re-establish a connection with a previously paired device, the current pairing must be disabled first. To re-establish a link please go to the desired device name and press connecting to re-connect with the BT380: Settings → Bluetooth Setup → Paired Devices → select a device (such as Sony Ericsson K800i) → Conn Sony Ericsson K800i Nokia 6230I Sony Ericsson K800i Conn Del Exit To delete a pairing simply select th
