Manual de instrucciones de Philips Cineos 3135 035 22913

Resumen del contenido incluido en la página 1

HDTV Monitor HDTV Monitor
44PL9523
55PL9523
44PL9522
55PL9223
Highlights
• Liquid-crystal-on-silicon (LCOS) High-definition
Imaging
•High-resolution Display—1280 x 720 pixels
Features
•Digital Natural Motion™
•Active Control™—analyzes and adjusts incoming signal
•Two-tuner, Double-window PIP (Picture-in-Picture)
®
•Dolby Virtual Surround, 40-watt RMS
•3D Y/C Comb Filter
•HD Component and DVI Input
•Center Channel Audio Input
• Side AV Convenience Jacks
•Matching stand and swivel available
Refer

Resumen del contenido incluido en la página 2

Positioning the TV Before connecting accessory devices—VCR, DVD player, or HD Situate the TV where it will not be receiver, for example—please keep the following in mind: exposed to heat or moisture. • Place the TV on a flat surface. An unlevel surface may adversely For safety, do not affect picture performance. set objects on top • Do not place the TV on shag carpet or any surface that will of the TV. block the air inlets at the bottom of the set. Blockage will cause the TV to overheat and shut

Resumen del contenido incluido en la página 3

Mounting the Swivel and TV to the Stand Install the plastic position pins in the stand. 1 Place the TV and mounted swivel on the stand, aligning the 1 2 front and sides of the TV with the front and sides of the 2 Positioning stand. This will help properly seat the TV on the position- ing pins and align the pre-drilled holes on the stand and Pins swivel. You do not need the rubber bumpers and long screws if you have already attached the swivel to the TV. Use the supplied screws (2) and screw key

Resumen del contenido incluido en la página 4

Making Basic Connections to the TV Cable Box with RF IN/OUT Back of TV Connect the incoming cable TV signal to the CABLE IN jack on the back of the cable box. Incoming 1 Cable TV Connect a coaxial cable (not supplied) to the TO TV jack Signal on the back of the cable box and to the TUNER jack on the DVI 2 G back of the TV. S-VIDEO RL V Set the Output Channel switch on the back of the cable box to CH 3 or 4 (whichever is correct for your cable box), 3 then tune the TV to the corresponding channe

Resumen del contenido incluido en la página 5

Making Basic Connections to the TV Antenna Back of TV Connect the incoming antenna signal to the TUNER jack on the back of the TV. See page 8 for details on using Autoprogram to store channels in the TV’s memory. NOTE: This connection will supply stereo sound to the TV if it is being broadcast by the station you are watching. DVI G S-VIDEO RL V DVI G Pr Pb Y S-VIDEO RL V Pr Pb Y RL V RL V RL RL RL RL V G S-VIDEO RGB+HV Incoming RL STANDARD/ Pr Pb Y HD INPUTS TUNER STANDARD/ Pr Pb Y HD INPUTS RL

Resumen del contenido incluido en la página 6

Using the Remote Control Remote Control REMOTE CONTROL BATTERIES (shown from the bottom) To load the supplied batteries into the remote: Remove the battery compartment door on the back of 1 the remote. 1 Place the batteries (2-AA) in the remote. Be sure the (+) HELPFUL HINT and (–) ends of the batteries line up correctly (the inside of When the batteries in your remote 2 the case is marked). control run low, the remote control will send a “Battery low” command Reattach the battery compartment

Resumen del contenido incluido en la página 7

Using the On-screen Menu The TV’s on-screen menu controls are viewed within a The first time you turn on the TV after purchasing it, it will be in a special mode designed to mobile map or pipe system. This system allows you to inform you that you can change the menu language and on-screen displays to English, French, or move along linked paths tied to specific Feature Title cate- Spanish. Also included in this mode is Autoprogram to encourage you to have the set program gories (“TV,” “Picture,”

Resumen del contenido incluido en la página 8

Using the Installation Features Language When you plug in your TV for the first time it will prompt you to set the Language and Autoprogam the channels. Language Autoprogram For Spanish- and French-speaking TV owners, an on-screen English Press the cursor down to select your menu language Language option is present. The Language control enables Français you to set the TV’s on-screen menu to be shown in either Español INFO SELECT DNM English, Spanish, or French. TV CC SURR HD SCREEN Press the C