Resumen del contenido incluido en la página 1
Resumen del contenido incluido en la página 2
TABLE OF CONTENTS Introduction 2-5 Adjustment 24-26 Safety symbol review and signal word review ............2 Program the travel limits ...........................................24 Preparing your garage door ........................................3 Setting the force........................................................25 Tools ............................................................................3 Test the safety reversal system.................................26 ® Planning ...........
Resumen del contenido incluido en la página 3
Resumen del contenido incluido en la página 4
Resumen del contenido incluido en la página 5
LOCK LIGHT Carton Inventory Your garage door opener is packaged in two cartons model purchased. If anything is missing, carefully which contain the motor unit and the parts illustrated check the packing material. Parts may be stuck in the below. Note that accessories will depend on the foam. KEEP THE FOAM INTACT (see page 6.) Remote Control Transmitter Visor Clip ® SECURITY✚ 3-Button Remote Control Belt Cap Retainer Motion Detecting Styrofoam Door Control Panel 2-Conductor Bell Wire White & Wh
Resumen del contenido incluido en la página 6
WARNING WARNING ASSEMBLY STEP 1 CAUTION WARNING Attach the Rail to the Motor Unit To avoid SERIOUS damage to garage door opener, use ONLY those bolts/fasteners mounted in the top of To avoid installation difficulties, do not run the the opener. garage door opener until instructed to do so. • Remove the two washered bolts mounted in top of motor unit. Washered Bolts • Align rail and styrofoam over sprocket. Cut tape 5/16"-18x1/2" Motor Unit from rail, belt and styrofoam. Sprocket • REMOVE STYRO
Resumen del contenido incluido en la página 7
ASSEMBLY STEP 3 WARNING WARNING Attach the Belt Cap Retainer To avoid possible SERIOUS INJURY to fingers from moving garage door opener: • Position the belt cap retainer over the opener CAUTION WARNING • ALWAYS keep hand clear of sprocket while operating sprocket so the two holes in cap align with the two opener. holes in mounting plate. Attach with #8x3/8" hex • Securely attach sprocket cover BEFORE operating. screws provided. You have now finished assembling your garage door opener. Please rea
Resumen del contenido incluido en la página 8
Resumen del contenido incluido en la página 9
ONE-PIECE DOOR WITHOUT TRACK Unfinished Ceiling 1. Close the door and mark the inside vertical centerline of your garage door. Extend the line Structural onto the header wall above door, as shown. Supports Header Wall If headroom clearance is minimal, you can install the header bracket on the ceiling. See page 10. 2x4 2x4 If you need to install the header bracket on a 2x4 (on wall or ceiling), use lag screws (not provided) OPTIONAL to securely fasten the 2x4 to structural supports CEILING MOUNT
Resumen del contenido incluido en la página 10
Resumen del contenido incluido en la página 11
INSTALLATION STEP 3 Attach the Rail to the Header Bracket • Position the opener on the garage floor below the header bracket. Use packing material as a protective base. NOTE: If the door spring is in the way you’ll need help. Have someone hold the opener securely on a temporary support to allow the rail to clear the spring. • Position the rail bracket against the header bracket. Header Wall • Align the bracket holes and join with a clevis pin Header Bracket as shown. Belt Pulley Bracket • Insert
Resumen del contenido incluido en la página 12
WARNING WARNING INSTALLATION STEP 4 CAUTION WARNING Position the Opener To prevent damage to garage door, rest garage door opener rail on 2x4 placed on top section of door. Follow instructions which apply to your door type as illustrated. SECTIONAL DOOR OR ONE-PIECE DOOR WITH TRACK A 2x4 laid flat is convenient for setting an ideal door-to-rail distance. Rail • Remove foam packaging. • Raise the opener onto a stepladder. You will need help at this point if the ladder is not tall enough. • Open
Resumen del contenido incluido en la página 13
Resumen del contenido incluido en la página 14
Resumen del contenido incluido en la página 15
Resumen del contenido incluido en la página 16
INSTALLATION STEP 9 WARNING WARNING Electrical Requirements To prevent possible SERIOUS INJURY or DEATH from electrocution or fire: To avoid installation difficulties, do not run the CAUTION WARNING • Be sure power is not connected to the opener, and opener at this time. disconnect power to circuit BEFORE removing cover to To reduce the risk of electric shock, your garage door establish permanent wiring connection. opener has a grounding type plug with a third • Garage door installation and wiri
Resumen del contenido incluido en la página 17
INSTALLATION STEP 10 WARNING WARNING ® Install The Protector System Be sure power is not connected to the garage door opener BEFORE installing the safety reversing sensor. The safety reversing sensor must be connected CAUTION WARNING and aligned correctly before the garage door To prevent SERIOUS INJURY or DEATH from a closing opener will move in the down direction. This is a garage door: required safety device and cannot be disabled. • Correctly connect and align the safety reversing sensor. Th
Resumen del contenido incluido en la página 18
INSTALLING THE BRACKETS DOOR TRACK MOUNT (RIGHT SIDE) Figure 1 Be sure power to the opener is disconnected. Install and align the brackets so the sensors will face Door each other across the garage door, with the beam no Track higher than 6" above the floor. They may be installed Lip in one of three ways, as follows. Indicator Light Garage door track installation (preferred) (Figure 1): • Slip the curved arms over the rounded edge of Sensor each door track, with the curved arms facing the Brac
Resumen del contenido incluido en la página 19
MOUNTING AND WIRING THE SAFETY SENSORS Figure 5 • Slide a 1/4"-20x1/2" carriage bolt head into the slot Wing Nut on each sensor. Use wing nuts to fasten sensors to brackets, with lenses pointing toward each other across the door. Be sure the lens is not obstructed by a bracket extension (Figure 5). Carriage Bolt 1/4"-20x1/2" • Finger tighten the wing nuts. Lens • Run the wires from both sensors to the opener. Use insulated staples to secure wire to wall and ceiling. TROUBLESHOOTING THE SAFETY
Resumen del contenido incluido en la página 20
