Resumen del contenido incluido en la página 10
MICROSOFT WINDOWS NT 4.0 - NEW INSTALLATION 1. Install the Transiton (EFA020X series) Adapter card in accordance with your personal computer user's manual. Again, follow all handling procedures to avoid electro-static discharges. 2. Start Windows NT, and open the control panel by clicking "Start," then "Settings," then "Control Panel." 3. Double Click on "Network." 4. Click on the Adapters tab. 5. Click "Add" inside the Network control panel, then select "Adapter." 6. Select "Have Disk." 7. I
Resumen del contenido incluido en la página 11
MICROSOFT WINDOWS NT 4.0 - SOFTWARE UPGRADE 1. Start Windows NT, and open the control panel by clicking "Start," then "Settings," then "Control Panel." 2. Double Click on "Network." 3. Click on the Adapters tab. 4. Highlight the existing Transition LANart adapter, and click "Remove." Close the control panel to effect the change. 5. Re-open the Network control panel, and click "Add," then select "Adapters." 6. Select "Have Disk." 7. Insert the Transition Driver Disk into the drive For the NDIS
Resumen del contenido incluido en la página 12
NOVELL NETWARE 4.X / 5.X - NEW INSTALLATION 1. Power off the machine. 2. Install the Transiton / LANart (EFA020X ) Adapter card in accordance with your personal computer user's manual. Again, follow all handling procedures to avoid electro-static discharges. 3. Install the server software 4. When the NIC selection menu appears, place the appropriate disk in the drive 5. Press Insert (Ins) 6. Press [F3] to change the path. 7. When you see the A: prompt, type \Novell\Nwsrvr41 for Netware 4.
Resumen del contenido incluido en la página 13
NOVELL NETWARE 4.X/ 5.X - SOFTWARE UPGRADE/ADDING NETWORK CARD TO AN EXISTING SYSTEM. 1. Shutdown Netware Server and power-off the machine. 2. Install the Transiton / LANart (EFA020X series) Adapter card in accordance with your personal computer user's manual. Again, follow all handling procedures to avoid electro- static discharges. 3. On the server’s prompt , type: LOAD INSTALL for 4.x Type: NWCONFIG for 5.X 4. Choose - "Driver Option" 5. Select - Configure Network driver" 6. Select
Resumen del contenido incluido en la página 14
MICROSOFT WINDOWS NT 4.0 - PERMANET SERVER The PermaNet Server feature allows users to configure a pair of LANart PCI device based NIC as primary and secondary, and provides the ability to automatically fail-over from primary adapter to the secondary adapter should the link status of the primary go down 1. Shutdown Windows NT and power-off the machine. 2. Install the two identical Transition / Lanart (EFA020X) Adapter card in accordance with your personal computer user's manual. Again, follo
Resumen del contenido incluido en la página 15
INSTALLING SUNSOFT SOLARIS DRIVER (X86 ENVIRONMENT) 1. Login as root 2. Copy from the media /solaris/pnt-solaris.pkg to /var/spool/pkg 3. At the prompt. Type, Pkgadd – d pnt-solaris.pkg and follow the instruction on the screen 4. Wait for the process to complete 5. Restart the computer. Your Transition Networks / LANart adapter is now configured. To access your network, protocols will need to be configured. Please see your network administrator for details DMI INSTALLATION PROCEDURE (DMI
Resumen del contenido incluido en la página 16
COMPLIANCE INFORMATION DECLARATION OF CONFORMITY Name of Mfg: Transition Networks 6475 City West Parkway, Minneapolis MN 55344 USA Model: N-xX-xx-01 and ND-xX-xx-01 Series PCI Cards Part Number: N-FX-ST-01, N-FX-SC-01, N-FX-MT-01, N-SX-ST-01, N-SX-SC-01, N-SX-MT-01, ND-FX-ST-01, ND-FX-SC-01, ND-FX-MT-01, ND-SX-ST-01, ND-SX-SC-01, ND-SX-MT-01 Regulation: EMC Directive 89/336/EEC Purpose: To declare that the N-xX-xx-01 or ND-xX-xx-01 to which this declaration refers is in conformity with the fo
Resumen del contenido incluido en la página 1
™
Ethernet 10/100BASE-SX, 100BASE-FX
PCI Network Interface Cards
N-FX-ST-01, N-FX-SC-01, N-FX-MT-01,
N-SX-ST-01, N-SX-SC-01, N-SX-MT-01,
ND-FX-ST-01, ND-FX-SC-01, ND-FX-MT-01,
ND-SX-ST-01, ND-SX-SC-01, ND-SX-MT-01
USER’S GUIDE
Adapter Hardware Installation ...................................................2
PCI Network Interface Cards......................................................3
Adapter Software Installation Note ............................................4
Microsoft Windows 95 -
Resumen del contenido incluido en la página 2
ADAPTER HARDWARE INSTALLATION Follow Instructions outlined in the indicated personal computer user’s guide for installing PCI Bus add- in cards into a PCI slot that supports bus mastering. CAUTION: Heed the warnings in the PC user ‘s guide in regard to proper protection against static discharge. Always hold the adapter by the metal bracket. Always be properly grounded when handling an adapter. Since adapters are designed with CMOS ICs and are particularly sensitive to static discharge. Failu
Resumen del contenido incluido en la página 3
PCI NETWORK INTERFACE CARDS TRANSITION Networks Fiber-Optic PCI Network Interface Cards (Adapters) are 32-bit bus-mastering PCI cards that support both half-duplex and full-duplex operation and that comply with PCI Specifications, revision 2.1 and 2.2, and with both IEEE 802.3 10BASE-FL, N-FX-xx-01 ND-FX-xx-01 N-SX-xx-01 ND-SX-xx-01 100BASE-SX, and 100BASE-FX standards N-FX-xx-01 One (1) ST, SC, or MT-RJ adapter connection (indicated as xx) to 100BASE-FX. N-SX-xx-01* One (1) ST, SC, or MT-RJ ad
Resumen del contenido incluido en la página 4
ADAPTER SOFTWARE INSTALLATION NOTE TRANSITION Networks Fiber-Optic PCI Network Interface Cards (Adapters) are shipped with one (1) CD driver disk containing software drivers for various network operating systems, diagnostic utilities, and electronic format documentation. Follow the directions in this user’s guide (also provided on disk) to install the indicated software driver. Software installation instructions that follow include statements written in the format: “ type - A:
Resumen del contenido incluido en la página 5
21. When the system comes up open Netowok Neighborhood by right clicking 22. Click on " Properties" 23. Highlight "Transition \ LANart …." And , Click on "Properties" 24. Click on Advanced 25. Chose the properties as required by Network Administrator 26. To access your network, protocols will need to be configured. Please see your network administrator for details. 27. If your computer is not Plug and Play compatible, open the control panel by clicking "Start," then "Settings," then
Resumen del contenido incluido en la página 6
MICROSOFT WINDOWS 95 - SOFTWARE UPGRADE 1. Power up the computer, and start Windows 95. 2. The following instruction is to update the driver for LANart network card. 3. Update the driver for Transition Networks / LANart (EFA020X) - open the control panel by clicking "Start," then "Settings," then "Control Panel." 4. Double Click "system" 5. Click "Device Manager" 6. Double Click "Network Adapter" 7. Highlight "Transition Networks / LANart…." And , Click on "Properties" 8. Click on "Driver"
Resumen del contenido incluido en la página 7
MICROSOFT WINDOWS 98 - NEW INSTALLATION 1. Copy the appropriate device install script For NDIS3 MAC driver type copy A:\Win98\Nids3\Mac\Netamd.inf C:\Windows\Inf For NDIS4 MINIPORT driver type copy A:\Win98\Nids4\Mini\Netamd.inf C:\Windows\Inf 2. Shutdown Windows 98 and power-off the machine. 3. Install the Adapter card in accordance with your personal computer user's manual. Again, follow all handling procedures to avoid electro-static discharges. 4. Turn the computer on to start Windo
Resumen del contenido incluido en la página 8
19. Double Click "system" 20. Click "Device Manager" 21. Double Click "Network Adapter" 22. Highlight " …." And , Click on "Properties" 23. Click on Advance 24. Chose the properties as required by the Network Administrator 25. Restart the computer. Your adapter is now configured. To access your network, protocols may need to be configured. Please see your network administrator for details. 8
Resumen del contenido incluido en la página 9
MICROSOFT WINDOWS 98 - SOFTWARE UPGRADE 1. Power up the computer and start Windows 98. 2. Update the driver for the PCI card - open the control panel by clicking "Start," then "Settings," then "Control Panel." 3. Double Click "system" 4. Click "Device Manager" 5. Double Click "Network Adapter" 6. Highlight "LANart…." and Click on "Properties" 7. Click on "Driver" and Click on "Update Driver" 8. Click on "Next" and choose - "No, Select Driver from List." 9. Click "Next" and Highlight the A
