Resumen del contenido incluido en la página 1
Resumen del contenido incluido en la página 2
1 ENGLISH
Resumen del contenido incluido en la página 3
ENGLISH Dear customer, Congratulations on your purchase of a Bazooka high-performance amplifier. At Bazooka, we are fanatics about accurate music reproduction. Your selection of our products for your sound system indicates that quality sound is also important to you too. At SAS, we take great pride in manufacturing revolutionary audio products, and through the years of engineering expertise, hand craftsmanship and critical testing procedures, we have created this high-performance series
Resumen del contenido incluido en la página 4
SAFETY PRECAUTIONS Fuse amplifiers power wire at the battery. Be sure to fuse the power wire within 12” of the car's battery. This will protect the car's battery in case of a short circuit between the power amplifier and battery. THIS IS A MUST, the amplifier's built-in fuse will only protect the power amplifier not the car's battery! Use high grade wire connectors. To ensure maximum power transfer and secure safe connections, it is recommended to use high grade barrier spades (for connec
Resumen del contenido incluido en la página 5
ENGLISH FEATURES AND BENEFITS DC Offset Protection This circuit protects the output of the amplifier against DC voltage. If for some reason DC voltage is detected at the output stage, the amplifier will shut down protecting the speakers from direct current. Short Circuit Protection The circuit protects the amplifier from damage due to a short found in the speakers or wiring. If one of the speakers or its wiring comes in contact with ground, the amplifier will shut down. To resume normal o
Resumen del contenido incluido en la página 6
Subsonic Filter (ELA1190, ELA1300, ELA1500 & ELA1800) A subsonic filter has been provided to filter out unwanted subsonic bass frequencies below the audible range of the subwoofer. This feature helps to improve the amplifier's overall performance since power is not wasted reproducing frequencies beyond the speakers' normal operating range. This feature works in conjunction with the Low-pass crossover to provide band-pass filtering. Phase Adjustment (ELA1190, ELA1300, ELA1500 & ELA1800) T
Resumen del contenido incluido en la página 7
ENGLISH MOUNTING LOCATION Before you start the installation, it will be necessary to find a mounting location for the amplifier. Find a location in which the amplifier will receive adequate ventilation in order to dissipate the heat it develops during operation. Two popular mounting locations are in the trunk or under the seat. Select the location in which you wish to mount the amplifier. Use caution when mounting amplifier, there are many wires, gas lines, vacuum lines, brake lines a
Resumen del contenido incluido en la página 8
POWER CONNECTIONS PROTECT FUSES +12V REM GND SP SP SP SP 25A 25A 25A POWER SPEAKERS IN IN-L -LIN INE E P PO OW WE ER R F FU US SE E M MO OU UN NT TE ED D W WIT ITH HIN IN 1 12 2" " F FR RO OM M B BA AT TT TE ER RY Y R RE EC CO OM MM ME EN ND DE ED D (N (NO OT T P PR RO OV VID IDE ED D) ) R RA AD DIO IO'S 'S R RE EM MO OT TE E T TU UR RN N- -O ON N O OU UT TP PU UT T + + - - 9 94 4..7 7 C CA AR R B BA AT TT TE ER RY Y + +1 12 2V V IMPORTANT! Before making any connections, disconnect the car’s b
Resumen del contenido incluido en la página 9
ENGLISH SIGNAL CONNECTIONS Connect the RCA output of the head unit (AM/FM cassette player, CD, or DAT) to the RCA input terminals of the amplifier. To make these connections, we recommend high quality RCA cables, which are available at your local car audio retailer. Run signal wires away from electrical wires to avoid possibility of induced noise from the car's electrical system (i.e. popping noises or engine noise). Please note that when making these connections the signal inputs correspon
Resumen del contenido incluido en la página 10
HIGH LEVEL CONNECTIONS (OPTIONAL) High Level inputs have been included to connect the amplifier to a radio without low-level outputs (i.e. factory radio). This connection will allow you to connect directly to the speaker output of the radio with out the need of an external adapter. Determine the type of radio you have and make one of the following connections. CAUTION! Before making any connections determine the type of radio to avoid possible damage to amplifier and/or radio. LINE IN LINE
Resumen del contenido incluido en la página 11
ENGLISH HIGH INPUT HIGH INPUT LINE IN BASS BOOST X-OVER X-OVER BASS BOOST LINE IN 6dB 12dB LPF HPF LPF HPF 6dB 12dB 0dB FLAT FLAT 0dB GND GND CH1 CH2 CH3 CH4 CH1 CH3 MIN MAX 50Hz 250Hz MIN MAX 50Hz 250Hz GAIN X-OVER X-OVER GAIN CH1 / CH2 CH3 / CH4 CH2 CH4 9 94 4..7 7 B BL LA AC CK K ( (G GR RO OU UN ND D) ) ( (N NO OT T U US SE ED D) ) G GR RE EE EN N L LE EF FT T + + G GR RA AY Y//B BL LA AC CK K R RIIG GH HT T - - L LE EF FT T - - G GR RE EE EN N//B BL LA AC CK K G GR RA AY Y R RIIG GH HT
Resumen del contenido incluido en la página 12
SPEAKER CONNECTIONS Make the speaker connections using speaker wire that is at least 16 gauge or heavier. As with any audio component, proper phasing of the amplifier and speakers is essential for strong bass response. When connecting, make sure that positive (+) from the amplifier is connected to the positive (+) of the speaker, and the same for negative (-). Please note that although the ELA1190, ELA1300, ELA1500 and ELA1800 are mono amplifiers, we have provided two sets of speaker termin
Resumen del contenido incluido en la página 13
ENGLISH SPEAKER CONNECTIONS (BRIDGED) The ELA amplifiers are capable of being bridged in a mono configuration. This feature allows you the flexibility of using the amplifier to drive a ** subwoofer or a center channel. In this configuration the amplifier sums the right and left channel to deliver one channel (mono) output. Please note: in order for the amplifier to sum right and left signal information, both right and left RCA connections must be made. **CAUTION! In the bridged mode, the a
Resumen del contenido incluido en la página 14
++ -- -- SPEAKER CONNECTIONS (TRI-MODE) The ELA265, ELA2100 and ELA2150 are capable of running in a Mono / Stereo mode. This feature gives the amplifier the ability to run stereo satellites (midbass & tweeter) simultaneously with a mono subwoofer. These connections are more complicated because they require the use of passive crossover networks (Not provided) to divide the frequencies to the speakers. We have included a sample diagram for 4 Ohm connections. If you wish to use multiple spea
Resumen del contenido incluido en la página 15
ENGLISH REMOTE BASS CONTROL MODULE (OPTIONAL) Before connecting the remote, it will be necessary to find a mounting location that will be easy to access for adjustment. Once you select your mounting location, you will need to run the control wire from the remote to the amplifier. To avoid possibility of induced noise from the car's electrical system (i.e. popping noises or engine noise), run the cable from the remote to the amplifier away from the car's electrical wiring. LINE IN LINE OUT
Resumen del contenido incluido en la página 16
ADJUSTING THE X-OVER AND BASS . (Please note: If you intend to use the ELA265, ELA2100 and ELA2150 in the Tri-mode configuration, it is necessary to set the crossover control to the “FLAT” setting in order to receive full range output) The “ELA” amplifiers are equipped with a built-in crossover network allowing you to select the crossover type (i.e. Low-Pass or Hi-Pass) and the desired crossover point. For example if you wish to drive a pair of subwoofers, you can select the “Low Pass” set
Resumen del contenido incluido en la página 17
ENGLISH TROUBLE SHOOTING THE SYSTEM We have put together this trouble-shooting guide if you experience problems after installing the amplifier. Please keep in mind that the majority of problems incurred are caused by improper installation and not the equipment itself. In addition, there are many components in the system that could cause various signal problems such as inducted electrical noise and engine noise. Before you can properly address the problem, you must first find the component
Resumen del contenido incluido en la página 18
SPECIFICATIONS ELA265 ELA465 ELA2100 ELA1190 Output Power @ 14.4 VDC : 4 ohm 65W x 2 64W x 4 100W x 2 100W x 1 2 ohm 95W x 2 90W x 4 150W x 2 190W x 1 Bridged 4ohm 190W x 1 170W x 2 300W x 1 N/A Bridged 2ohm N/A N/A N/A N/A Frequency Response + - 5dB 25Hz-22KHz 25Hz-22KHz 25Hz-22KHz 25Hz- 250KHz S/N Ratio (A-weight) >90dB >90dB >90dB >90dB THD (A-weight) .30% .30% .30% .30% Low Input Level 200mV-6V 200mV-6V 200mV-6V 200mV-6V Hi Input Level 1.0V-10.0V 1.0V-10.0V 1.0V-10.0V 1.0V-10.0V Battery Vol
Resumen del contenido incluido en la página 19
ENGLISH LIMITED WARRANTY Southern Audio Services, Inc., warrants all products to be free from defects in material and workmanship for a period of one (1) year from the date of purchase. In the event the product is not as warranted, SAS’ sole obligation shall be to repair or replace the defective product at SAS’ option: SAS limits its obligation under any implied warranties under state laws to a period not to exceed the limited warranty period. SAS and its authorized BAZOOKA® dealers spec
Resumen del contenido incluido en la página 20
How to obtain warranty services: 1. You are responsible for delivery of the product to an authorized BAZOOKA® dealer or contact SAS at 1-800-THE TUBE for a Return Authorization number. The Return Authorization number must be clearly written on the outside of the box. Freight must be prepaid to SAS. Warranty replacement parts will be returned freight prepaid. The entire enclosure may be returned for warranty service, but return will be freight collect. 2. You must provide proof of th
