Resumen del contenido incluido en la página 1
PROJECTOR
User’s Manual
HDP2300 High Definition Projector
Resumen del contenido incluido en la página 2
Copyright This publication, including all photographs, illustrations and software, is protected under international copy- right laws, with all rights reserved. Neither this manual, nor any of the material contained herein, may be reproduced without written consent of the author. © Copyright 2010 Disclaimer The information in this document is subject to change without notice. The manufacturer makes no represen- tations or warranties with respect to the contents hereof and specifically discl
Resumen del contenido incluido en la página 3
HDP2300 Users Manual Important Safety Information Important: It is strongly recommended that you read this section carefully before using the projector. These safety and usage instructions will ensure that you enjoy many years of safe use of the projector. Keep this manual for future reference. Symbols Used Warning symbols are used on the unit and in this manual to alert you of hazardous situations. The following styles are used in this manual to alert you to important information.
Resumen del contenido incluido en la página 4
Preface Projector Installation Notice Place the projector in a horizontal position The tilt angle of the projector should not exceed 15 degrees, nor should the projector be installed in any way other than the desktop and ceiling mount, otherwise lamp life could decrease dramatically. Allow at least 50 cm clearance around the exhaust vent. Ensure that the intake vents do not recycle hot air from the exhaust vent. When operating the projector in an enclosed space,
Resumen del contenido incluido en la página 5
HDP2300 Users Manual Replacing the Lamp Replacing the lamp can be hazardous if done incorrectly. See Replacing the Projection Lamp on page 35 for clear and safe instructions for this procedure. Before replacing the lamp: Unplug the power cord. Allow the lamp to cool for about one hour. Cleaning the Projector Unplug the power cord before cleaning. See Cleaning the Projector on page 37. Allow the lamp to cool for about one hour. Regulatory Warnings Before installing and using the
Resumen del contenido incluido en la página 6
Preface Table of Contents GETTING STARTED .......................................................................................................................................................... 1 PACKING CHECKLIST........................................................................................................................................................... 1 VIEWS OF PROJECTOR PARTS.............................................................................................
Resumen del contenido incluido en la página 7
HDP2300 Users Manual TROUBLESHOOTING ..................................................................................................................................................... 39 COMMON PROBLEMS AND SOLUTIONS ............................................................................................................................... 39 TIPS FOR TROUBLESHOOTING .......................................................................................................................
Resumen del contenido incluido en la página 8
HDP2300 Users Manual GETTING STARTED Packing Checklist Carefully unpack the projector and check that the following items are included: HDP2300 SERIES PROJECTOR WITH LENS CAP REMOTE CONTROL VGA CABLE COMPONENT CABLE POWER CORD (WITH TWO AA BATTERIES) HDMI CABLE CD-ROM WARRANTY CARD QUICK START GUIDE (THIS USER’S MANUAL) Contact your dealer immediately if any items are missing, appear damaged, or if the unit does not work. It is recommend that you keep th
Resumen del contenido incluido en la página 9
HDP2300 Users Manual Views of Projector Parts HDP2300 Series Front-right View ITEM LABEL DESCRIPTION SEE PAGE: IR receiver Receives IR signal from remote control 1. 8 Lens Projection Lens 2. Focus ring Focuses the projected image 3. 18 Zoom ring Enlarges the projected image 4. 5. Height adjuster Adjusts level of projector 17 See Top view—On-screen Display (OSD) buttons Function keys 6. 4 and LEDs. 7. Lamp cover Removes cover to replace lamp or color wheel 35 Vertical l
Resumen del contenido incluido en la página 10
HDP2300 Users Manual ITEM LABEL DESCRIPTION SEE PAGE: Horizontal lens shift Adjusts the image position horizontally 9. 19 Lens release button Press the release button before removing the lens 10. 13 Important: Ventilation openings on the projector allow for good air circulation, which keeps the projector lamp cool. Do not obstruct any of the ventilation openings. – 3 –
Resumen del contenido incluido en la página 11
HDP2300 Users Manual Top view—On-screen Display (OSD) buttons and LEDs SEE ITEM LABEL DESCRIPTION PAGE: 1. MENU Opens and exits OSD menus ▲ (Up cursor) / Navigates and changes settings in the OSD 21 2. Keystone+ Quick Menu – For Keystone ENTER Enter or confirm highlighted OSD menu item 3. BLANK Displays a blank screen and mutes audio 4. 5. ◄ (Left cursor) Navigates and changes settings in the OSD 21 6. AUTO Optimizes image size, position, and resolution ► (Right cursor)
Resumen del contenido incluido en la página 12
HDP2300 Users Manual Rear view ITEM LABEL DESCRIPTION SEE PAGE: VIDEO Connect the composite cable from a video device 1. YPbPr Connect a component video enabled device 2. 12 HDMI 1/ 2/ 3 Connect the HDMI CABLE from a HDMI device 3. USB Connect the USB cable from a computer 4. IR receiver Receive IR signal from remote control 5. 8 Red Error code Lamp is not ready (warming up/shutting LAMP LED 6. Flashing down/cooling) (see LED Error Messages on page 40) 40 TEMP LED
Resumen del contenido incluido en la página 13
HDP2300 Users Manual ITEM LABEL DESCRIPTION SEE PAGE: Connects the RGB cable from a computer and VGA/ SCART/ YPbPr 12. components 12 13. S-VIDEO Connects the S-Video cable from a video device AC IN Connects the power cable 14. 13 Power switch Turns on/off the projector 15. 15 Security chain lock Helps protect the HDP2300 from unauthorized use 16. 38 Secures to permanent object with a Kensington® Lock Kensington Lock 17. 38 system – 6 –
Resumen del contenido incluido en la página 14
HDP2300 Users Manual Bottom view ITEM LABEL DESCRIPTION SEE PAGE: Tilt adjustor Rotate adjuster lever to adjust angle position. 1. 17 Ceiling support holes Contact your dealer for information on mounting the projector on a ceiling 2. Note: When installing, ensure that you use only UL Listed ceiling mounts. For ceiling installations, use approved mounting hardware and M4 screws with a maximum screw depth of 6 mm (0.23 inch). The construction of the ceiling mount must be of a
Resumen del contenido incluido en la página 15
HDP2300 Users Manual Remote Control Functions Important: 1. Avoid using the projector with bright fluorescent lighting turned on. Certain high-frequency fluo- rescent lights can disrupt remote control operation. 2. Be sure nothing obstructs the path between the remote control and the projector. If the path be- tween the remote control and the projector is obstructed, you can bounce the signal off certain reflective surfaces such as projector screens. 3. The buttons and keys on the
Resumen del contenido incluido en la página 16
HDP2300 Users Manual ITEM LABEL DESCRIPTION SEE PAGE: 1. Power OFF Turns the projector off 13 HDMI 2 Displays the HDMI 2 source selection 2. S-VIDEO Displays the S-VIDEO source selection 3. VIDEO Displays the VIDEO source selection 4. Up cursor / Navigates and changes settings in the OSD 5. Keystone+ Quick Menu – For Keystone ENTER Enters and confirms settings in the OSD 6. 21 Right cursor 7. Navigates and changes settings in the OSD 8. Down cursor ASPECT RATIO Di
Resumen del contenido incluido en la página 17
HDP2300 Users Manual Remote Control Operating Range The remote control uses infrared transmission to control the projector. It is not necessary to point the remote directly at the projector. Provided you are not holding the remote perpendicular to the sides or the rear of the projector, the remote will function well within a radius of about 7 meters (23 feet) and 15 degrees above or below the projector level. If the projector does not respond to the remote control, move a little closer.
Resumen del contenido incluido en la página 18
SETUP AND OPERATION Inserting the Remote Control Batteries Remove the battery compartment cover 1. by sliding the cover in the direction of the arrow. Insert the battery with the positive side 2. facing up. Replace the cover. 3. Caution: 1. Only use AA batteries (Alkaline batteries are recommended). 2. Dispose of used batteries according to local ordinance regulations. 3. Remove the batteries when not using the projector for prolonged periods. — 11 —
Resumen del contenido incluido en la página 19
HDP2300 Users Manual Connecting Input Devices A PC or notebook computer and video devices can be connected to the projector at the same time. Video devices include DVD, VCD, and VHS players, as well as movie camcorders and digital still cameras. Check the user manual of the connecting device to confirm it has the appropriate output connector. ITEM LABEL DESCRIPTION VIDEO Connect the composite cable from a video device YPbPr Connect a component video enabled device HDMI 1/ 2/ 3
Resumen del contenido incluido en la página 20
HDP2300 Users Manual Installing or Removing the Optional Lens Caution: Do not shake or place excessive pressure on the projector or the lens components as the projec- tor and lens components contain precision parts. Before removing or installing the lens, be sure to turn off the projector, wait until the cooling fans stop, and turn off the main power switch. Do not touch the lens surface when removing or installing the lens. Keep fingerprints, dust or oil off the lens surface. Do
