Resumen del contenido incluido en la página 1
ORDER NO.
ARP3051
PROJECTION MONITOR RECEIVER
PRO-610HD
PRO-510HD
SD-582HD5
SD-532HD5
THIS MANUAL IS APPLICABLE TO THE FOLLOWING MODEL(S) AND TYPE(S).
Model
Type Power Requirement Remarks
PRO-610HD PRO-510HD SD-582HD5 SD-532HD5
KUXC/CA AC120V
KBXC –– –– –– AC120V
This service manual should be used together with the following manual(s):
Model No. Order No. Remarks
PRO-610HD ARP3047
CONTENTS
6. ADJUSTMENT ................................................ 195 7.2 IC .................................
Resumen del contenido incluido en la página 2
PRO-610HD, PRO-510HD, SD-582HD5, SD-532HD5 194
Resumen del contenido incluido en la página 3
PRO-610HD, PRO-510HD, SD-582HD5, SD-532HD5 6. ADJUSTMENT 6.1 INTRODUCTION • IMPORTANT When replacement of the following assemblies are required during repairs, be sure to replace the EEPROMs with the mounted ones in order to retain the adjustment data of the unit and to facilitate adjustment after the replacement of the assemblies. Name of Assy EEPROM Main Contents of Memory SIGNAL Assy IC2454 [24LC32(I)P] Adjustment data, such as W/B and color data, in FACTOR
Resumen del contenido incluido en la página 4
PRO-610HD, PRO-510HD, SD-582HD5, SD-532HD5 6.3 ADJUSTMENT LOCATION AND ITEMS Assembly Adjustment Location Focus VR (VR1) B CONV. AMP ASSY A DEFLECTION (SERVICE) ASSY C DIGITAL CONV. ASSY B G Focus VR R D VIDEO ASSY E SUB VIDEO ASSY Rear View F SIGNAL ASSY Front View Deflection Deflection Yoke (B) CRT assy G Yoke (G) CRT assy B CRT assy R Lens assy (For Green) Deflection Lens assy Lens assy Yoke (For Red) (For Blue) Deflection Yoke (R) TP-BK TP-GK B CRT DRIVE G CRT DRIVE R CRT DRIVE assy assy ass
Resumen del contenido incluido en la página 5
PRO-610HD, PRO-510HD, SD-582HD5, SD-532HD5 Assembly Adjustment Location Guide is repaired or replaced If POWER SUPPLY ASSY No adjustment is required 1 Brightness Adjustment (* 2) 3 Focus Adjustment (VR1: FOCUS VR) (* 2) is repaired or replaced If DEFLECTION SERVICE ASSY 5 Screen Size Adjustment (* 2) 6 Convergence Adjustment (* 2) 7 White Balance Adjustment (* 2) 5 Screen Size Adjustment (* 2) is repaired or replaced If CONV. AMP ASSY 6 Convergence Adjustment (* 2) 1 Brightness Adjustment (* 1)
Resumen del contenido incluido en la página 6
PRO-610HD, PRO-510HD, SD-582HD5, SD-532HD5 6.4 FACTORY ADJ MODE Start Start adjusting Factory Adjustment Mode Select 1st FACTORY ADJ mode, then adjust. 1st FAC Select 1st FACTORY ADJ Mode Selecting the mode for adjustment operations. Normal Start Front panel picture TV DTV TV/ /SA CBL T VCR DV /LD D TV ON/OFF POWER TV DTV INPUT 1 2 3 4 SPLIT SEARCH SELECT SCREEN SUB CH MODE ANT FREEZE DTV POWER The 2nd FACTORY AUDIO DISPLAY 1 2 3 INPUT1 Cyclically 4 5 6 ADJ mode is not used 7 8 9 ENTER CH 0 pos
Resumen del contenido incluido en la página 7
PRO-610HD, PRO-510HD, SD-582HD5, SD-532HD5 1 OTHER OFFSET mode To enter the OFFSET mode of each picture quality, use the following keys and codes of the remote control unit: Key(s) on the Remote Control Unit A STD OFFSET MODE DOWN C COMP (15 kHz) OFFSET MODE P in P CH-, SUB CH- D COMP (31 kHz, 33 kHz) OFFSET MODE P in P CH+, SUB CH+ B TV OFFSET MODE RED V COLOR TEMP B&W for STD DTV MENU L COLOR TEMP FILM for STD & GAME INFO T RGB OFFSET MODE CH ENTER 2 The screen size modes change cyclically wi
Resumen del contenido incluido en la página 8
PRO-610HD, PRO-510HD, SD-582HD5, SD-532HD5 6.5 ADJUSTMENT 1 Brightness Adjustment Start 1st FAC Input signal : Black Burst (INPUT 1) Black burst 0 TV/ CBL VCR DVD ADJUTMENT OFFSET TV DTV /SAT ON/OFF /LD POWER TV DTV INPUT 1 2 3 4 ADJUTMENT OFFSET SPLIT SEARCH SELECT SCREEN SUB CH b MODE ANT FREEZE (DOWN) DTV AUDIO DISPLAY 1 2 3 4 5 6 4 7 8 9 °
b 0 CH 0 ENTER CH ¢
CH RETURN CH VOL MUTING 4 CUTR EDIT/ TV/SAT/DVD DTV/DVD TOP LEARN MENU MENU SOURCE DTV/SAT PO POWER WER 5 GUID
Resumen del contenido incluido en la página 9
PRO-610HD, PRO-510HD, SD-582HD5, SD-532HD5 2 Deflection Yoke Adjustment 2 Deflection Yoke Lean Adjustment -1 • Input a stable signal (e.g. from an LD player or SG) to Start the INPUT 1 connector. • MENU → SETUP → Enter the MULTI-POINT (FULL) in the CONVERGENCE. • The cross hatch disappears if there is no operation with Deflection Deflection Yoke (L2) the remote control unit for about 8 minutes. If the cross Yoke (L1) hatch disappears, repeat the above operation with the CRT ASSY G CRT ASSY B C
Resumen del contenido incluido en la página 10
PRO-610HD, PRO-510HD, SD-582HD5, SD-532HD5 3 Focus Adjustment 3 -1 Focus Adjustment of Lens Assy Start Lens assy (For Green) Cross hatch Lens assy Lens assy (For Red) (For Blue) "Best focusing" 3 -2 Focus VR Adjustment Cross hatch Focus VR (VR1) B G FOCUS VR R Turn the Focus VR for best focusing. 202
Resumen del contenido incluido en la página 11
PRO-610HD, PRO-510HD, SD-582HD5, SD-532HD5 Test-cross Position Check 4 • Check the test-cross position. If it is located within ± 20 mm from the center of the screen, no adjustment is required. If it is not, adjust the position as follows: • Input a stable NTSC (480i) signal (e.g. from an LD player) and adjust the position. Start MENU → SETUP → CONVERGENCE → FULL TV/ CBL VCR DVD DTV /SAT /LD TV ON/OFF POWER TV DTV INPUT 1 2 3 4 SET/ SEARCH SELECT SPLIT SCREEN SUB CH MODE ANT FREEZE ENTER DTV
Resumen del contenido incluido en la página 12
PRO-610HD, PRO-510HD, SD-582HD5, SD-532HD5 5 Screen Size Adjustment Check if both vertical and horizontal sizes are within 91% ±2%. If they are not, perform the size adjustment as follows: 5 Size Mode -1 • Mode for roughly adjusting the horizontal and vertical sizes of the Note : Start 1st FAC main deflection. Screen mode : FULL • In this mode, the color is green only, screen size is FULL and the contrast a Data value is +10. ADJUTMENT FULL SIZE DTV TV/ /SA CBL T VCR DV /LD D TV ON/OFF
Resumen del contenido incluido en la página 13
PRO-610HD, PRO-510HD, SD-582HD5, SD-532HD5 Note : 5 -3 Note : Horizontal Size Adjustment Screen mode : FULL • After the V. SIZE adjustment, enter the H. SIZE adjustment 1st FAC Start by pressing "1" key. • After the H. SIZE adjustment, INPUT 1:Monoscope check that V. SIZE is 91– 2%. Green screen If not, readjust the V. SIZE. ANT 1 H.SIZE 91% ± 2% or VOL INPUT TV Adjust the size so that the picture is completely General displayed on the screen. broadcasting • Reference The H PHASE adjustment is
Resumen del contenido incluido en la página 14
PRO-610HD, PRO-510HD, SD-582HD5, SD-532HD5 CONVERGENCE ADJUSTMENT 6 The data stored in the EEPROMs are as follows: 1. Procedures IC1410 1. When replacinf the DIGITAL CONV. Assy, replace the EEPROM OFFSET CONVER. MODE 1 (DFH, DFV) of new DIGITAL CONV. Assy with the EEPROM of old OFFSET CONVER. MODE 3 DIGITAL CONV. Assy. Factory-preset values for convergence 2. Check the initial data for the convergence adjustment. User-adjusted values for convergence (CENTER, MULTI-POINT) 3. Perform
Resumen del contenido incluido en la página 15
PRO-610HD, PRO-510HD, SD-582HD5, SD-532HD5 Table 2 OFFSET CONVER DATA The cross-hatch signal is generated inside the unit, and is auto- matically displayed in OFFSET CONVER. mode and MANUAL OFFSET CONVER MODE 1 CONVERGENCE mode. You can turn on and off the cross-hatch Screen Mode Numeric Adjustment signal with the YELLOW key. F Z C N H Key Item Screen indication FULL ZOOM CINEMA NATURAL HD FULL 1 DFH 0F0 0D0 0D0 0D0 100 2 DFV 070 070 070 070 070 3 HDP 010 010 010 010 010 OFFSET CONVER MODE 2
Resumen del contenido incluido en la página 16
PRO-610HD, PRO-510HD, SD-582HD5, SD-532HD5 • Pattern for each adjustment item Key No. ` Key No. 1 Key No. 8 STATIC SKEW SIZE = Fixed position GH Key No. ` Key No. 1 Key No. 6 Key No. 8 STATIC SKEW PIN SIZE GV Note 1: When the green CRT is replaced, or when the deflection yoke for the green is replaced, prior to the convergence adjustment, tune the center of the image to the center of the screen by turning the centering magnet. Note 2: When the CONVER. AMP Assy or DIGITAL CONV. Assy is replaced
Resumen del contenido incluido en la página 17
PRO-610HD, PRO-510HD, SD-582HD5, SD-532HD5 3.4.3 3.4.4 Press the SET/ENTER key when the point to be adjusted is When adjustment of the selected point is finished, press the determined. SET/ENTER key, then adjust the other adjustment points by repeating 3.4.1 to 3.4.4. Screen indication 3.4.5 Make the adjustment for the green in each screen mode, and use the green as the standard screen for the red and the blue. To change screen modes, use the SCREEN mode key. Note: Some coordinates for adju
Resumen del contenido incluido en la página 18
PRO-610HD, PRO-510HD, SD-582HD5, SD-532HD5 In a case of an error in convergence: 4th step Repeat 2nd and 3rd steps to take total balance. Then the adjust- ment for the green is completed. To return from the fine adjustment mode to the coarse adjustment mode, press the MENU key once, then the DOT key. Adjustable points Note: When the MENU key is pressed to quit MANUAL CONVERGENCE mode, the display will be unstable for Good adjustment: several seconds. This is because the adjustment data are A
Resumen del contenido incluido en la página 19
PRO-610HD, PRO-510HD, SD-582HD5, SD-532HD5 • Pattern for each adjustment item Key No. ` Key No. 1 Key No. 7 Key No. 8 SKEW STATIC LIN SIZE RH BH Key No. ` Key No. 1 Key No. 4 Key No. 6 STATIC SKEW KEY PIN RV BV Key No. 8 Note 1: When the red CRT is replaced, or when the deflection SIZE yoke for the red is replaced, prior to adjustment, tune the center of the image to the center of the screen by turning = Fixed position the centering magnet. Note 2: When the CONVER. AMP Assy or DIGITAL CONV.
Resumen del contenido incluido en la página 20
PRO-610HD, PRO-510HD, SD-582HD5, SD-532HD5 When all the adjustments are completed, or to interrupt 3.6.5 adjustment, press the MENU key to quit Convergence Repeat procedures 3.6.2 through 3.6.4 for the other screen modes. Adjustment mode. The display will be unstable for several (Completion of the red adjustment) seconds, but this is because the data are being written to the EEPROM. Wait without doing anything until the display becomes stable, which means writing of data to the EEPROM is finis
