Resumen del contenido incluido en la página 1
COMPONENTS
HOME A U DIO
0 W N E R S
M A N U A L
Series 09130
A M P L I F I E R
P 0 W E R
Resumen del contenido incluido en la página 2
- IMPORTANT SAFETY INFORMATION NOTICE The lightning flash with arrowhead symbol within an equilateral triangle is intended to alert the user to the presence of uninsulated “dangerous voltage” within the products enclosure, that may Ap!!!J!A be of sufficient magnitude to constitute a risk of electric shock to persons. The exclamation point within an equilateral WARNING: TO PREVENT FIRE OR triangle is intended to alert the user of the presence of important operating and mainte- SHOCK HAZARD, DO NO
Resumen del contenido incluido en la página 3
11. NON-USE PERIODS During periods of extended non-use, the power cord should be unplugged from the power source. 12. CLEANING The equipment should be cleaned only as detailed in the operating instructions. 13. OBJECT AND LIQUID ENTRY Care should be taken so that objects and/or liquids, such as cleaning fluids or beverages, are not spilled into the enclosure of the equipment. 14. DAMAGE REQUIRING SERVICE Hafler equipment should be serviced by qualified service personnel when: A. The power supply
Resumen del contenido incluido en la página 4
TABLE OF CONTENTS SPECIFICATIONS ............................................................................................ 4 PERFORMANCE General Information ............................................................................................................... 4 INSTALLATION Rackmounting ........................................................................................................................ 5 Ventilation/Placement ...................................................
Resumen del contenido incluido en la página 5
PERFORMANCE SPECIFICATIONS All specifications are for 20 Hz - 20 kHz, at full power into 8 ohms, unless specified otherwise. 65 watts per channel (8 ohms) Power Rating: less than 0.008% Rated THD: Full Power Bandwidth: 4 Hz to 40 kHz Signal to Noise Ratio: greater than 100 dB, unweighted 22,000 ohms Input Impedance: Input Sensitivity: 1.1 volts RMS Damping Factor: 100 to 1 kHz, 50 to 10 kHz Power Switch, Left/Right Gain Controls, Mono/Stereo Switch Controls: Right and Left/Mono RCA jacks Inputs:
Resumen del contenido incluido en la página 6
INSTALLATION The 9130 Amplifier is supplied in either a 17” Black Version, or a 19” Silver Version. The 19” model RACKMOUNTING has rackmounting holes provided for installation in equipment racks. The holes are on standard EIA spacings. Due to conflict with adjacent equipment, it may be advisable to remove the four rubber feet from the bottom of the unit. The feet may be removed from the outside, with no dis-assembly of the chassis necessary. VENTILATION/ The 9130 Amplifier can produce considerab
Resumen del contenido incluido en la página 7
POWER SWITCH UP - ON LEFT/MONO DOWN - OFF GAIN I (3, I RACKMOUNT HOLES RIGHT (19” VERSION ONLY) GAIN 9130 AMPLIFIER FRONT PANEL VIEW
Resumen del contenido incluido en la página 8
-7-
Resumen del contenido incluido en la página 9
All output connections to the amplifier must be performed with the amplifier off! OUTPUTS The left and right audio outputs from the amplifier are via standard 5-way type, 3/4” spacing, binding posts. Connect these binding posts to the loudspeakers. The amplifier’s binding posts will accept single or dual banana plugs, spade lugs, pin plugs, or bare wires. If using bare wires, it is recommended that the ends of the wire be tinned with solder so that no stray strands can cause a short circuit to t
Resumen del contenido incluido en la página 10
CIRCUIT HIGHLIGHTS The 9130 employs a single ended, current source driven, differential input stage. This stage is connected to the rest of the circuitry through a balanced push-pull current mirror system. A combination current mirror and bias multiplier drive the final output stage driver emitter followers. Special linearizing techniques are used that dramatically reduce harmonic distortion. The final output stage uses two multiple lateral MOSFET’s (Metal Oxide Semiconductor Field Effect Transi
Resumen del contenido incluido en la página 11
The 9130 Amplifier is equipped with a simple means to adjust the AC line voltage rating for 100, 120 CHANGING LINE or 230 volts AC, 50/60 Hz. The configuration is labelled above the power cord connector. If the amplifier VOLTAGE RATING will be used in a location that requires a different line voltage, use the following procedure to change the configuration. Review the modification instructions before attempting this procedure. If any doubts exist about one’s ability to change the line voltage, i
Resumen del contenido incluido en la página 12
Apply power to the amplifier, and allow the unit to thermally stabilize for about three minutes. (If 4) using an analog meter, and the meter reads backwards, temporarily remove power and reverse the meter leads.) Again referring to the diagram, locate the trimmer potentiometer labelled Pl for the left channel, 5) or Pl 01 for the right channel. (NOTE: Do not confuse these trimmers with those labelled P2 and P102: these are for distortion control and require specialized test equipment to adjust.)
Resumen del contenido incluido en la página 13
SPECIAL NOTE ON VIDEO CABLE “GROUNDS”: As mentioned above, the ground conductor of cable service and antenna feeds should be connected to earth ground. Often, however, due to long feed lengths, especially in apartment distribution systems, this ground will be of poor quality and could be a source of noise. This interference is usually characterized by a high frequency noise, rather than a hum or a buzz. If such interference is experienced, a separate earth ground connection should be made from t
Resumen del contenido incluido en la página 14
LEFT/MONO (+I LEFT LEFT/MONO - OUTPUT INPUT MONO/STEREO RIGHT RIGHT - OUTPUT INPUT THERMAL SOFT THERMAL - I PROTECTION TURN ON/OFF SENSORS - SYSTEM SYSTEM A 4 9130 FUNCTIONAL BLOCK DIAGRAM
Resumen del contenido incluido en la página 15
PARTS LIST Parts values and types subject to change without prior notice. DESIGNATORS 1 -99: LEFT CHANNEL DESIGNATOR VALUE PART NUMBER 101-l 99: RIGHT CHANNEL 0.001,Polypropylene CPP-102 C8,C108 201-299: COMMON PARTS C9,C109 100, Electrolytic CER-107C 301-399: CHASSIS/POWER SUPPLY C10,C110 0.1, Polyester CP-104A C11,C111 0.1, Polyester CP-104A DESIGNATOR VALUE PART NUMBER 0.033,Polypropylene C12,C112 CPP-333 C13,C113 0.1, Polyester CP-104A ALL RESISTORS 1/4 WATT, 1% METAL FILM C14,C114 100, E
Resumen del contenido incluido en la página 16
w a’L c4 m IL I/L bO
Resumen del contenido incluido en la página 17
Ll TSl u ‘2.5 cl’- u $ u 1 cl’ n XI cl, 1 m I ou r”l CAUTION: d FOR CO-NliNUED PROTECTION - - u .- - AGAINST FIRE HAZARD. F4 AMP REPLAGE ONLY WITH SAME TYPE AND RATING FUSES.
Resumen del contenido incluido en la página 18
JlOl RIGHT INPUT 96 2N5401 Jl LEFT INPUT CR6 b lN4146 1. ALL RESlSTORS IN OHMS 2. Au. CAPACITORS IN MICROFARADS 3. yxg3N~ psr..s~~oRsz CR8 ,I lN4146 lil-i99: RIGhT CHANNEL 201-298: COMMON PARTS 301-399: cHASsIs/powER SUPPLY 4. LEFT CMNNEL ONLY SHOWN 5. STEREO/MONO !MilCH SHOWN IN STEREO PCStllON 6. ,~XAGEIXINCTOR SHOWN IN 7. LINE FUSE VALUE: lOO-lZO\Ac: 5A SLO-Bu) 23OVACz 2.5A SLO-BLO 9 130 CIRCUIT SCHEMATIC DIAGRAM REVISED S/3/92 UNE FUSE (SEE NOTES) .
Resumen del contenido incluido en la página 19
Fl R17 l +HV 47.5 SA Cl1 I 0.1 -ca +-CQ 1 “01; K) 8: c,\ Ql.j--- I ZN5550 5’ R18 a12 l-9 2SK1056 475 @ 4 -z- LL lN4148 10 --e--- R14 R26 22.1K , R13 l.lK 27 of3 % 1” 1% 2N2222 RlOq SK : I 1 : I Q13 R21 b 2SJl60 221 010 CR8 ,I lN414.8 2N5401 I %.Y 1 N4%? T F2 1 * *-NV V‘ 5A TO L CH.@ TO R. CH. @ I CIRCUIT SCHEMATIC DIAGRAM RMSEC g/3/92 zo4 R211 3.3K R207 R206 I .,-.I# c ..Y T r- R215 I I R208 1
Resumen del contenido incluido en la página 20
SERVICE POLICY AND LIMITED WARRANTY If you encounter any difficulty or have any question concerning your 9130 Amplifier, please call our Customer Service Department weekdays, 8 a.m. to 3:30 p.m., Mountain Standard Time, at 602-967- 3565. Should you have any doubts as to whether the amplifier is malfunctioning and requires service, please call us before sending in for repair. All units being returned (regardless of warranty status) must receive a Return Authorization (RA) number. In addition, we
