Resumen del contenido incluido en la página 1
SR835 Crossover
A Harman International Company
Owner’s Manual
Resumen del contenido incluido en la página 2
Warning For your protection, please read the following: Water and Moisture: Appliances should not be used near water (e.g. near a bathtub, washbowl, kitchen sink, laundry tub, in a wet basement, or near a swimming pool, etc.) Care should be taken so that objects do not fall and liquids are not spilled into the enclosure through openings. These symbols are internationally accepted symbols that warn of potential Power Sources: The appliance should be connected to a power hazards with electrical pr
Resumen del contenido incluido en la página 3
SR835 Crossover 1 INTRODUCTION Congratulations, and thank you for your purchase of the DOD SR835 Crossover. The SR835 is a high quality sound reinforcement tool capable of providing your PA or sound reinforcement system with speaker protection and the increased clarity and efficiency that results when bi-amping, or tri-amping. So what is bi-amping, and tri-amping? A bi-amped system means you are using two power amps to drive separate ranges of frequencies.The crossover is doing a two way split,
Resumen del contenido incluido en la página 4
SR835 Crossover 2 FRONT PANEL 1 2 34 56 7 8 9 10 1112 1. Power Switch - Used to engage or disengage the power to the SR835. 2. Mono/Stereo Switch - This switch configures the SR835 as two indepen- dent channels of 2 way splits, or one channel with a 3 way split.When the switch is in and the LED is lit, the SR835 is in Mono mode. 3. Gain - This is the input level for Channel 1 in Stereo mode, and is the mas- ter input level in Mono mode. 4. Low Level - This knob controls the volume for the low fr
Resumen del contenido incluido en la página 5
SR835 Crossover 3 REAR PANEL 120 V 60 Hz WARNING: TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK DO NOT REMOVE BACK. NO USER WARNING: SHOCK HAZARD-DO NOT OPEN OR 100 V 50 Hz DO NOT EXPOSE THIS EQUIPMENT TO RAIN OR MOISTURE. SERVICEABLE PARTS INSIDE. REFER SERVICING TO QUALIFIED SERVICE PERSONNEL. AVIS: RISQUE DE CHOC ÉLECTRIQUE-NE PAS OUVRIR HIGH BAL. HIGH UNBAL. LOW BAL. LOW UNBAL. STEREO INPUT LOW SUM OUT HIGH BAL. HIGH UNBAL. LOW BAL. LOW UNBA
Resumen del contenido incluido en la página 6
SR835 Crossover 4 INSTALLATION Install the crossover in a rack with the provided rack screws. Route the AC power cord to a convenient power outlet away from audio lines. The unit may be turned on and off using the front panel power switch. Since the units draw a relatively small amount of current during idle, they can be left on continuously. DOD crossovers generate very little heat during operation and thus do not need to be specially ventilated or cooled. The units should not, however, be sub
Resumen del contenido incluido en la página 7
SR835 Crossover 5 BI-AMP APPLICATIONS For bi amp applications, the SR835 must be set to the Stereo mode regardless of whether you are running in stereo or mono. The Stereo mode configures the SR835 as two individual channels, each providing a two way split. If you are run- ning your sound system in stereo, both channels would be used: one for the left, and one for the right. If you are running in mono, only one of these channels would be used but the SR835 would still be set to Stereo mode in or
Resumen del contenido incluido en la página 8
SR835 Crossover 6 TRI-AMP APPLICATIONS For tri amp applications, the SR835 must be set to the Mono mode. The Mono mode configures the SR835 as one channels providing a three way split. If you are running your sound system in stereo, you would need two SR835s in order to run a Stereo tri amp configuration. The following procedure outlines the steps for running a tri amped system. Begin with the power turned off. 1. Make sure the Mono Mode switch on the front panel of the SR835 is in the “in” posi
Resumen del contenido incluido en la página 9
SR835 Crossover 7 Begin sending signal through the system. Gradually increase the High, then Mid, and finally Low Levels in order checking for correct wiring.Then balance the tonality of the source signal.You may also need to increase the Gain if a stronger signal is required. STEREO USING A MONO SUB-WOOFER The setup procedure is the same as for the stereo bi amp application, except that instead of connecting both low frequency outputs, connect only the Low Frequency Sum output to the low frequ
Resumen del contenido incluido en la página 10
SR835 Crossover DOD WARRANTY 8 1. The warranty registration card must be mailed within ten days after pur- chase date to validate this warranty. 2. DOD warrants this product, when used solely within the U.S., to be free from defects in material and workmanship under normal use and service. 3. DOD Electronics liability under this warranty is limited to repairing or replacing defective materials that show evidence of defect, provided the prod- uct is returned through the original dealer, where all
Resumen del contenido incluido en la página 11
DECLARATION OF CONFORMITY Manufacturer’s Name: DOD Electronics Corporation Manufacturer’s Address: 8760 S. Sandy Parkway Sandy, Utah 84070, USA declares that the products: Product Name: SR835 Product Options: All conform to the following product specifications: Safety: EN 60065 (1993) IEC65 (1985) with Amendments 1,2,3 EMC: EN 55013 (1990) EN 55020 (1991) Supplementary Information: The products herewith comply with the requirements of the Low Voltage Directive 73/23/EEC and the EMC Dir
Resumen del contenido incluido en la página 12
VISIT DOD ELECTRONICS ON THE WORLD WIDE WEB AT HTTP://WWW.DOD.COM DOD ELECTRONICS CORPORATION 8760 SOUTH SANDY PARKWAY SANDY,UTAH 84070 TELEPHONE 801-566-8800 FAX 801-566-7005 INTERNATIONAL DISTRIBUTION 8760 SOUTH SANDY PARKWAY SANDY,UTAH 84070 TELEPHONE 801-568-7638 FAX 801-568-7642 DOD IS A REGISTERED TRADEMARK OF HARMAN MUSIC GROUP INC. © 1998 DOD ELECTRONICS CORPORATION DOD 18-3844-A-01 PRINTED IN CHINA
