Manual de instrucciones de MB QUART ONYX ONX4.125

Resumen del contenido incluido en la página 1

ONYX
Lower power amplifiers will clip earlier than their more powerful cousins,
Installation Manual
and cause loudspeaker failure when overdriven, due to the harmonics
generated by a clipped signal, thus overheating voice coils.
Amplifiers should be mounted with the fins running horizontally for best
Congratulations!
convection cooling, to minimize overheating. Purchase the best quality
By purchasing an amplifier from MB Quart, you have decided on a product
RCA cables you can afford, for r

Resumen del contenido incluido en la página 2

Index WARRANTY 1 INSTALLATION INSTRUCTIONS General Instructions 2 Settings for Best Performance 3

Resumen del contenido incluido en la página 3

WIRE GAUGE INSTALLATION INSTRUCTIONS General Instructions General: Run the wiring so that RCA cables are at least 18“ away from power and speaker cables. Keep RCA cables away from electrical devices in the vehicle that can cause electrical noise, such as electric fuel pumps, emission control modules and other on-board electronic modules. Power and ground connections:(See table below) Use a sufficient gauge power cable and ground cable using the chart below as reference to what size wire you req

Resumen del contenido incluido en la página 4

INSTALLATION INSTRUCTIONS Settings for Best Performance ONX4.60 / ONX4.80 / ONX4.125 / ONX80.4/500 General: At this point you are ready to get more specific on the settings for your amplifier. High Pass: -When in Hi Pass operation, this setting acts as a low frequency cut off for your system reproduction. The point that you set it at cuts off any frequencies from reproduction beyond this point. The 12 o’clock position is a great starting point. EXAMPLE: If you adjust the High Pass to 100Hz, the

Resumen del contenido incluido en la página 5

TROUBLE SHOOTING The key to finding the problem in a misbehaving sound system is to isolate parts of that system in a logical fashion to track down the fault. Description of the Diagnostic system built into all MB Quart amplifiers The diagnostic system will shut down the amplifier, until reset by turning the head unit off, and back on. This state of affairs will be indicated by the front panel PROTECT LED lighting up under the following conditions: 1 - A short circuit on the loudspeaker leads.

Resumen del contenido incluido en la página 6

CH3/4 CH1/2 LEVEL BASS EQ X-OVER HPF LPF LINE OUT CH3/4 CH1/2 LEVEL BASS EQ X-OVER HPF LPF LINE OUT POWER POWER R R R R PROTECTION PROTECTION 6V 0.2V 0dB 12dB FULL LPF HPF 60Hz 13KHz 30Hz 250Hz 6V 0.2V 0dB 12dB FULL LPF HPF 60Hz 13KHz 30Hz 250Hz MODE MODE L L L L 6V 0.2V 0dB 12dB FULL LPF HPF 60Hz 13KHz 30Hz 250Hz 2 6V 0.2V 0dB 12dB FULL LPF HPF 60Hz

Resumen del contenido incluido en la página 7

CH3/4 CH3/4 CH1/2 LINE INPUT CH1/2 LINE INPUT HI PASS LEVEL HI PASS X-OVER LOW PASS LEVEL HI PASS LEVEL HI PASS X-OVER LOW PASS LEVEL X-OVER HI FULL BP X-OVER HI FULL BP HI FULL HI FULL CH4 CH2 CH4 CH2 10Hz 15Khz 6V 0.2V 10Hz 15Khz 30Hz 150Hz 6V 0.2V 10Hz 15Khz 6V 0.2V 10Hz 15Khz 30Hz 150Hz 6V 0.2V 5CH 5CH PROTECT PROTECT CH1 CH3 30Hz 150Hz 0dB-10dB 6V 0.2V Ch2 Ch4 Ch5 CH1 CH3 30Hz 150Hz 0dB-10dB 6V 0.2V Ch2 Ch4 Ch5 REMOTE REMOTE LOW PASS BASS EQ LEVEL POWER LOW PA

Resumen del contenido incluido en la página 8

OUTPUT INPUT LEVEL BASS EQ REMOTE SUBSONIC LOW PASS POWER L L PROTECT 6V 0.2V 0dB 10dB 15Hz 35Hz 30Hz 250Hz R R ONX1.1000D / ONX1.1500D OUTPUT INPUT LEVEL BASS EQ REMOTE SUBSONIC LOW PASS POWER Mono Amplifiers L L PROTECT 6V 0.2V 0dB 10dB 15Hz 35Hz 30Hz 250Hz R R FEATURES: - 1 Set of RCA inputs - POWER LED: Indicates the powered up and turned on condition - LEVEL: Var

Resumen del contenido incluido en la página 9

/

Resumen del contenido incluido en la página 10

OEM Integration Accessories MX-1 Premium High To Low Level Converter MX-3 Bass Controller * Converts High Level OEM speaker wires to Ultra Clean RCA Low Level Outputs * High Level Inputs: Accepts all types of High level Inputs * Parametric Bass EQ: Provides a wide array of subwoofer output signal including floating ground and high voltages up to 30 volts. shaping controls to enhance bass response and sound quality including * Audio Signal Sense / Hardwire Turn-On: Audio sense detec

Resumen del contenido incluido en la página 11

Check out our videos of new products, events and technical tutorials at www.youtube.com/maxxsonicsusainc PART#S110 ONX4.60 / ONX4.80 / ONX4.125 / ONX4.80/500 / ONX1.1000D / ONX1.1500D