Resumen del contenido incluido en la página 1
1275 Danner Dr Tel:330-562-7070
R NETWORK
Fax:330-562-1999
TECHNOLOGIES Aurora, OH 44202
www.networktechinc.com
NTI INCORPORATED
®
VEEMUX Series
SM-nXm-15V-LCD
Video Matrix Switch
Installation and Operation Manual
MAN067 Rev Date 2/27/2007
Resumen del contenido incluido en la página 2
TRADEMARK VEEMUX is a registered trademark of Network Technologies Inc in the U.S. and other countries. COPYRIGHT Copyright © 1999-2007 by Network Technologies Inc. All rights reserved. No part of this publication may be reproduced, stored in a retrieval system, or transmitted, in any form or by any means, electronic, mechanical, photocopying, recording, or otherwise, without the prior written consent of Network Technologies Inc, 1275 Danner Drive, Aurora, Ohio 44202. CHAN
Resumen del contenido incluido en la página 3
TABLE OF CONTENTS Introduction....................................................................................................................................................................1 Basic Operation ...........................................................................................................................................................1 Supported Web Browsers..................................................................................................
Resumen del contenido incluido en la página 4
Specifications.............................................................................................................................................................27 IRT Troubleshooting ..................................................................................................................................................27 DDC Support..............................................................................................................................................
Resumen del contenido incluido en la página 5
NTI VEEMUX VIDEO MATRIX SWITCH INTRODUCTION The SM-nXm-15V-LCD (n = number of inputs (video sources), m = number of outputs (monitors)) video matrix switch (VEEMUX) allows any of up to 32 video sources to output to any or all of up to sixteen (16) monitors. The configuration of the VEEMUX is determined at time of order (i.e. 16x4, 8x16, etc.). The bandwidth of the SM-nXm-15V-LCD is 200MHz and video resolutions through 1900 x1200 are supported with no degradation. The switch can be con
Resumen del contenido incluido en la página 6
NTI VEEMUX VIDEO MATRIX SWITCH Materials Materials Supplied with this kit: • NTI SM-nXm-15V-LCD Video Matrix switch • IEC Line cord, country specific • 4-#10-32 x 3/4" pan head screws and 10-32 cagenuts (server cabinet mounting hardware) • CD with: a pdf file of this owner's manual the NTI Discovery Tool the Matrix Switcher's Control Program Cables All cables are sold separately. The following tables list the available stocked cab
Resumen del contenido incluido en la página 7
NTI VEEMUX VIDEO MATRIX SWITCH Front View of SM-8X8-15V-LCD 1 2 10 3 IN OUT 12 3 4 5 6 7 8 1 2 R 3 DDC NTI 4 R Network Technologies Inc VEEMUX Esc Out 6 78 9 0 5 * 6 7 1 2 3 4 5 Enter Menu In 8 Rear View of SM-8X8-15V-LCD ETHERNET R R S NTI 2 1275 Danner Dr VIDEO VIDEO MONITOR MONITOR Aurora, OH 44202 7 8 5 6 3 4 1 2 7 8 5 6 3 4 1 2 3 www.nti1.com 2 Tel:330-562-7070 Fax:330-562-1999 4 56 8 7
Resumen del contenido incluido en la página 8
NTI VEEMUX VIDEO MATRIX SWITCH INSTALLATION Connect the Sources and Monitors 1. Turn OFF power to all video sources (inputs) that will be connected to the VEEMUX before connecting or disconnecting any cables. 2. Connect a VEXT-xx-MM cable from the video port of a video source to a 15HD female video connector labeled VIDEO 1 on the VEEMUX. (See Fig. 1) 3. Connect additional video sources to remaining 15HD female VIDEO x connectors as desired. Rear View of SM-8
Resumen del contenido incluido en la página 9
NTI VEEMUX VIDEO MATRIX SWITCH Connect RS232 RS232 control can be achieved using a separate user terminal or CPU with a terminal program. To make a terminal connection, connect a serial cable (specifications on page 31) between the user terminal and the 9 pin DIN female connector on the VEEMUX labeled "RS232". (See Fig. 3) Rear View of SM-8X8-15V-LCD R R NTI S 2 1275 Danner Dr VIDEO VIDEO MONITOR MONITOR 7 8 5 6 3 4 1 2 7 8 5
Resumen del contenido incluido en la página 10
NTI VEEMUX VIDEO MATRIX SWITCH Power Up 1. Plug the VEEMUX into an AC power outlet. 2. Turn ON power to the VEEMUX. 3. Turn ON power to the video sources and monitors connected to the VEEMUX. LED MATRIX (not available on all models) The LED Matrix is a grid of LEDs on the front panel of the VEEMUX. This grid is used to provide a visual indication of all connections between video sources and destinations. To determine if an input (video source) is connected to an output (vid
Resumen del contenido incluido en la página 11
NTI VEEMUX VIDEO MATRIX SWITCH CONTROL OPTIONS The VEEMUX video matrix switch has four methods of control: • Front Panel LCD with Keypad • Directly via an RS232 Interface • Remotely via Ethernet (rack mount models only) • Infrared Remote (optional). Every unit comes standard with the Front Panel LCD with Keypad, and RS232 built in. Rack mount models also include Ethernet connection. If desired, the Infrared option must be requested at the time of the order. The Infrared opti
Resumen del contenido incluido en la página 12
NTI VEEMUX VIDEO MATRIX SWITCH Scan Mode Scan Mode causes an output port to automatically switch from one input port to the next consecutive input port after a specified period of time (referred to as the dwell time). Port switching will continue indefinitely and no ports will be skipped, whether there are video sources connected to them or not. If desired, the VEEMUX can be configured to skip the scanning of specific ports using the RS232 Command Protocol (page 9) or Telnet (page
Resumen del contenido incluido en la página 13
NTI VEEMUX VIDEO MATRIX SWITCH On the DB-9 female connector, pins 4 (DSR) and 6 (DTR) are shorted and pins 7 (CTS) and 8 (RTS) are shorted. Therefore, host handshaking is bypassed and TXD and RXD are the only active signals. A straight through DB-9 cable (not null modem) will work for most CPUs. To daisy chain multiple units, use NTI Matrix-Y-1 "Y" cables, except for the last unit connected. (see Fig 6). For a pinout of the Matrix-Y-1 cable, see page 32. For straight through cable p
Resumen del contenido incluido en la página 14
NTI VEEMUX VIDEO MATRIX SWITCH Command Definitions (Cont'd) Command Good Response Description String RS SW * Internal Reset RV SW,00 *string\0 Read NTI Version String RU SW *IP,OP Read Unit Size EA SW,ip * Set the IP address, ip is in xxx.xxx.xxx.xxx format, number of digits is minimum 1 and maximum 3 for each field Leading zeroes are accepted EM SW,ip * Set the Subnet mask, ip is in xxx.xxx.xxx.xxx format, number of digits is minimum 1 and maximum 3 fo
Resumen del contenido incluido en la página 15
NTI VEEMUX VIDEO MATRIX SWITCH Matrix Switcher's Control Program For Windows 9X, NT, 2000 AND XP The Matrix Switcher's Control Program is an easy and powerful graphical program that controls NTI matrix switches through an RS232 interface. The Matrix Switcher's Control Program is included on the CD packaged with the VEEMUX. The Matrix Switcher's Control Program is downloaded by clicking on the link "Download Matrix Switcher's Control Program" found on the web page that appears wh
Resumen del contenido incluido en la página 16
NTI VEEMUX VIDEO MATRIX SWITCH Ethernet Operations Key Selection Description 1) Set Unit IP Address - enter the desired IP address in xxx.xxx.xxx.xxx format - number of digits is minimum 1 and maximum 3 for each field. Leading zeroes are accepted 2) Set Unit Subnet Mask - enter the desired IP address in xxx.xxx.xxx.xxx format - number of digits is minimum 1 and maximum 3 for each field. Leading zeroes are accepted 3) Set Unit Default Gateway - enter the desired default gateway
Resumen del contenido incluido en la página 17
NTI VEEMUX VIDEO MATRIX SWITCH ETHERNET CONTROL Telnet Interface The Telnet Interface enables the user to control the switch using telnet client through an Ethernet connection. The telnet server listens on port 2000. To access the telnet interface, using the current IP address type the following in a command shell: telnet 192.168.1.30 2000 The VEEMUX will prompt the user for a password. The user must enter the password followed by . The factory default password is
Resumen del contenido incluido en la página 18
NTI VEEMUX VIDEO MATRIX SWITCH Notes: 1. The commands must be typed exactly as shown in the chart. The commands are case sensitive. 2. If a mistake is made, the user must backspace to the beginning and completely retype the command. 3. If a command is sent that the VEEMUX does not recognize or exceeds the configuration of the switch, the reply "?" may be received. Check the command syntax and try again. 4. To quit the telnet session, press the keyboard keys
Resumen del contenido incluido en la página 19
NTI VEEMUX VIDEO MATRIX SWITCH Video Switch Page The Video Switch page (right) displays the active connections (shown in orange) and enables the user to control the video connections of the VEEMUX. Up to 100 different connection configurations can be saved and later recalled by any connection method. Note: If changes are made using the keypad (pg.7) or by another user through the web interface, you must refresh the screen using your browser to see those changes. N
Resumen del contenido incluido en la página 20
NTI VEEMUX VIDEO MATRIX SWITCH To save a configuraton, from the Stored Configurations user interface, use the drop-down list to select the desired slot (numbers 0-99) to save the active configuration into and press the Save button. Note: This will save the currently active configuration on the VEEMUX. If changes have been made in the web interface without first pressing the Submit button, those changes will not yet be part of the active configuration. Note: If changes to the
