Resumen del contenido incluido en la página 1
n
450 mm (17-314") MODEL UH4510A
630 mm (24-3/4") MODEL UH6310A
Equipped with electric brake
INSTRUCTION MANUAL
SPECIFICATIONS
Effective cutting
Strokes Dimensions Net
MODEL
blade length
per minute IL x W x HJ weight
450 mm
825 mm x 180 mm x 170 mm 3.2 kg
UH4510A 1.800
[ 17.314")
(32-112" x 7-118" x 6-518") (7.0 Ibs)
____
630 mm
1,000 mm x 180 mm x 170 mm 3.4 kg
UH6310A 1,800
(24-314") (39-318'' x 7.118" x 6-518") (7.5 IbsJ
* Manufacturer reserves the right to change specifi
Resumen del contenido incluido en la página 2
IM PO RTANT SAFETY INSTRUCTIONS (For All Tools) WARNING - TO REDUCE THE RISK OF INJURY, BASIC SAFETY PRECAUTIONS SHOULD BE OBSERVED. INCLUDING THE FOLLOWING: READ AND FOLLOW ALL INSTRUCTIONS. DRESS PROPERLY - Do not wear loose clothing or jewelry. They can be 1. caught in moving parts. Use safety glasses and nonskid footwear. Use of sturdy gloves is recommended. 2. STAY ALERT - Watch what you are doing - use common sense. Do not operate trimmer when fatigued. 3. DANGER - RISK OF CUT
Resumen del contenido incluido en la página 3
Total Length of Cord in Feet 25 50 100 150 - I 18 1 16 16 14 AWG Size of Cord Contact Makita Authorized or Factory Service Center if a proper extension cord cannot be found. 15. Inspect blades periodically and replace before operation if damaged. 16. Hold the tool firmly with both hands. 17. Do not leave the tool running. Operate the tool only when hand-held. 18. Attention! Do not expose this tool to rain. The tool must not be left outdoors and it must not be used when wet. 19. Be ca
Resumen del contenido incluido en la página 4
Installing grip Attach the grip onto the grooves in the tool side and secure with the two screws. WARN I NG : DO NOT USE WITHOUT GRIP. Hook Power cord When using an extension cord, secure it I to the tool‘s cord with the hook provided. 1 I Cord connector 1 Attach the hook about 100-200 mm (4”- 8”) from the extension cord connector. This will help prevent unintentional discon- nection. Extension cord Switch action To prevent the trigger from being acciden- tally pulled, a lock-
Resumen del contenido incluido en la página 5
Operation Refer to the Important Safety Instructions before operation. Do not attempt to cut branches thicker than 12 mm (15/32") diameter with this trimmer. These should first be cut with shears down to the hedge trimming level. Hold the trimmer with both hands and move it in front of your body. When operating the trimmer, keep exten- I sion cord behind trimmer. Never drape it Sturdy gloves over hedge being trimmed. To cut a hedge top evenly, it helps to tie a string or cord at t
Resumen del contenido incluido en la página 6
To cut a hedge side evenly, i it helps to cut from the bottom upwards. Trim boxwood or rhododendron from the base toward the top for a nice appearance and good job. CAUTION : 0 Be careful not to accidentally contact a metal fence or other hard objects while trim- ming. The blade will break and may cause serious injury. 0 Do not attempt to trim too much at a time, or malfunction of the tool may result. 0 Overreaching with a hedge trimmer, par- ticularly from a ladder, is extremely dan-
Resumen del contenido incluido en la página 7
MAINTENANCE CAUTION : Always be sure that the tool is switched off and unplugged before attempting to perform inspection and maintenance. Blade maintenance After operation, clean off the blades (both sides) with a stiff brush. Then wipe the blades with a cloth and coat them with light machine oil. After use When storing the tool, use the convenient hole in the bottom of the tool handle to hang the tool on a wall from a nail or hook. a certain length. When this occurs, The tool will
Resumen del contenido incluido en la página 8
ACCESSORIES CAUTION : These accessories or attachments are recommended for use with your Makita tool specified in this manual. The use of any other accessories or attachments might present a risk of injury to persons. The accessories or attachments should be used only in the proper and intended manner. 0 Blade cover Hook Part No. 158024- 1 Part No. 414247-4 (For model UH4510A) Part No. 414248-2 (For model UH6310A) Shear blade assembly Part No. 125008-4 (For model UH4510A) No. 12500
Resumen del contenido incluido en la página 9
Mar-13 '89 US I HEDGE TRIMMER @- 450 mm (17-3/4") Model UH4510A 630 mm (24-3/4") Model UH6310A Note: The switch and other part configurations may differ from country to country. 9
Resumen del contenido incluido en la página 10
MODEL UH4510A. UH6310A Mar -13-'8Y US I;,'," AtD DESCRIPTION "",M DESCRIPTION MACHINE MACHINE ~ ~ 1 1 Housing Sel (With Item 261 22 1 Fan 70 23 1 2 1 Sponge Seal Bail Bearing 6OYLB 3 1 Switch 24 2 Receptacle Sleeve 4 1 Cord Guard 25 2 Carbon Brush 1 5 1 Cord 26 Housing Sei fWith lfem 11 6 1 Strain Relief 27 5 Tapping Screw 4x20 1 7 2 Pan Head Screw M4x18 (With Washerl 28 Name Plate 8 1 Switch Lever 29 3 Pan Head Screw M5x55 [With Washerl Y 1 Lock Off Button 30 1 Grip 27 11 1 Com
Resumen del contenido incluido en la página 11
MAKITA LIMITED ONE YEAR WARRANTY Warranty Policy Every Makita tool is thoroughly inspected and tested before leaving the factory. It is warranted to be free of defects from workmanship and materials for the period of ONE YEAR from the date of original purchase. Should any trouble develop during this one-year period, return the COMPLETE tool, freight prepaid, to one of Makita’s Factory or Authorized Service Centers. If inspection shows the trouble is caused by defective workmanship or mater
